Where is the VAZ-2114 8 valve engine number: photo and video

The need to verify the number

The arrow indicates where to look for the engine number

Whenever you buy a car, you need to check the engine number with what is on the documents. This applies to both registration and deregistration of the vehicle. Below, we will tell you where to find the engine number on a VAZ-2114 car.

The need to check the engine and body numbers, without exception, on any vehicle is primarily due to the fact that you do not purchase a stolen car.

Further, difficulties may arise if the engine is no longer original. It could have been changed, for example, removed from disassembly. And during verification, unnecessary problems will arise.

All numbers and letters indicated on the unit must completely coincide with those in the documents, excluding cases of correction . It is also necessary to pay attention to their integrity , that is, they should not have any mechanical damage.

Where can I look up the engine number on a VAZ-2114?

In total, there is one place on the car where the engine number is stamped - it is on the cylinder block on the right side, next to the thermostat, right above the clutch housing.

The engine number is clearly visible once you reach it.

The location of the number is indicated by an arrow.

Please note that in order to see it, you may need to dismantle the air filter housing, along with the pipes.

Information plate

The number is duplicated on the information plate on the right side of the front pillar, along with the engine body number, which is stamped below the spare wheel and the front pillar on the right.

The above plate is intended to inform the owner about all the information about the car: year of manufacture, manufacturer, etc. As in the case of the engine and body number, pay attention to the integrity of this plate, the absence of damage or chips on it. It itself should be smooth, and have intact rivets holding it in place.

If there are traces of rust on it, then it is best to clean it so that this does not subsequently affect the general condition of the information materials.

This is interesting: How to check the DMRV sensor on a VAZ

Bulletin board

It is worth noting the information table, which is located on the right at the reception. On the table there is a duplicate engine number and body number. In addition, it contains information about what year the car was produced, about the plant that produced it, etc. In fact, all information that is a priori basic.

READ How to Enable Climate Control on Opel Zafira

However, the fact that it only duplicates the meaning does not detract from its value. This means that her condition should also be good. If there are small areas of rust, they must be disposed of; if there are small chips that make access to information difficult, then, if possible, the plate should be replaced. The ideal condition is a smooth, rust-free surface and the presence of rivets that secure it to the car body.

Why do you need to know this?

Buying a car is a joyful event. But it may be overshadowed by the fact that during registration, unpleasant details will be revealed. Therefore, ALWAYS check that all vehicle identification data matches those indicated in its documents!

Of course, in different regions of the country, car inspectors have different views on the fact that a car may have an engine with a number that differs from what is indicated in the documentation. But traffic police officers may quite reasonably have questions if suddenly the engine number does not match. Isn't the motor you have stolen? Was it installed legally?

If the engine has been replaced on the car, then there must be all the documents that would confirm the legality of its installation.

Since the number of vehicles exceeds conceivable values, the VAZ 2107 engine number is an individual identifier of the product. In order to somehow distinguish the released product, the manufacturer has developed a product labeling method. The information encrypted in the code is specific only to the car on which it is applied, so it is difficult to mislead or try to deceive an informed user.

VAZ-2107:

Where is the room?

According to the requirements, the VAZ 2114 engine number is applied to the vehicle engine using the stamping method. It is located on the side of the cylinder block, to the right of the thermostat. Directly below the number is the clutch housing.

READ Which Engine For Renault Duster 1.6

When looking around the room, you should make sure:

1. That all its numbers match the numbers in the documents for the car.
2. All numbers were accurate and were not “killed” on top of each other.
3. All numbers have the same style and font size.
4. The point is that metal in a number field does not indicate interference.

If, when purchasing a car, it turns out that the numbers do not match those indicated in the documents, or the license plates look suspicious, it is better to refuse the purchase. After all, such a discrepancy will bring many problems to the new owner not only during registration, but also in the future.

Information plate

Phase sensor VAZ 2114 photo

The number is duplicated on the information plate on the right side of the front pillar, along with the engine body number, which is stamped below the spare wheel and the front pillar on the right.

Engine number VAZ 2107 where the injector is located.

The above plate is intended to inform the owner about all the information about the car: year of manufacture, manufacturer, etc.

As in the case of the engine and body number, pay attention to the integrity of this plate, the absence of damage or chips on it. It itself should be smooth, and have intact rivets holding it in place.

If there are traces of rust on it, then it is best to clean it so that this does not subsequently affect the general condition of the information materials.

Now, when buying a VAZ 14th model, it is absolutely not necessary to check the engine number, since the car has been discontinued and you can, within reasonable limits of course, even change its design, even if you plug in a used engine, no one will check it.

When purchasing and selling, the traffic police checks the numbers of all units

You are mistaken comrade, he will buy this piece of shit without checking the engine. And then, God forbid, of course, it turns out that this engine is wanted. There will be so many hemorrhoids

If you have an 8-valve engine, then its number should be located on the gearbox side, on the block where the thermostat is! And, a tip, for better access to the engine number, you will need to first remove the air filter.

When selling, you still need to go through verification, so the engine needs documents, no matter what it is

All VAZ 2115 models, starting from the year of manufacture, have a simple design, which easily allows you to check the engine number on a VAZ without referring to the official documentation of the vehicle. However, it is worth taking a closer look at the need for the number, its decoding and the contents of the information plate.

Checking and matching the engine number with the documents is the first thing a potential car owner should do before making a purchase. This operation needs to be carried out not only for VAZ cars. You can change or erase the engine number on any vehicle, regardless of the year and place of its production.

So, there are two reasons for confirming the number against official data:

• Registration of the vehicle. To the road inspection authorities, the presence of the correct VIN code indicates the legal origin of the car. However, this is not the only situation where they may need to be checked. If a similar car is listed as stolen, a traffic inspector has the right to stop the driver for a quick check. The absence of a whole number in this case can lead to unfavorable consequences.
• Purchasing a car on the secondary market. And if everything is very clear with the official requirements, then in the case of purchasing a vehicle from a private person, you need to be extremely vigilant. Stolen cars often have their license plates erased or changed. This is done so that there is no possibility of finding the car, and an inattentive buyer gives money for the car. One way or another, careful inspection before purchasing is a must.

This equally applies to people who are putting their car up for sale. Before this, it is necessary to check the integrity of the VIN code, the broken state of which may lead to the loss of the buyer.

So, now you need to determine where to look for the number and how to decipher it.

Where can I find the VIN number on the engine?

The VIN is a unique vehicle number that is responsible for its identification and helps ensure the difference between the vehicle and a similar one in the event of theft. It applies to all cars produced worldwide since the 1980s.

Wine number

on the VAZ 2114 it is located in three places:

1. The right fender is on a support inside the engine compartment.
2. There is an amplifier on the floor inside the luggage compartment.
3. On the “recap plate” located on the engine.

The number can be viewed directly on the engine in a summary table, which also contains other important information such as year of manufacture, total permissible weight, etc.

It is important to remember that all three numbers, two on the housing elements and one on the plate, must be the same. If the number on the nameplate does not match the number on the case, there is a chance that the engine is not original or the numbers have been broken.

How to decipher the VIN code

Now that information regarding where to look for the engine number on a VAZ 2114 has been found, it is important to determine the meaning of the VIN code. It is most rational to consider the information plate, which immediately indicates all the necessary requirements. It looks like this:

So, now in order:

• Serial number, which is intended for spare parts. It corresponds to the serial ID of the vehicle that came off the assembly line.
• A numeric value indicating the vehicle's approval type.
• Identification ID, in which XTA is the code of the plant that produced the car; 211440 — vehicle model; 6 - year in which the vehicle was produced; 0000000 (last 7 digits) - body serial ID.
• Numerical value of the installed motor model.
• Acceptable possible loading on the front axle.
• Acceptable and possible loading on the rear axle.
• Identification IDs of configuration and execution options.
• Permissible vehicle weight.
• Permissible weight of the vehicle if it has a trailer.

Knowledge of this information is necessary for basic literacy and the ability to navigate the main documentation of the vehicle.

Every driver should know where the VIN code is located in his car. This is confirmed not only by the main reasons, but also by situations that are impossible to predict. It's worth spending a few minutes once to avoid problems in the future.

This is interesting: How does a diesel fuel injection pump work?

Find out where the engine number is on a VAZ and other cars

An inexperienced person will spend up to an hour searching for the engine number under the hood of a car. First, let's decide for what purpose are you trying to find this number? If you need engine number information as such, you will find it on the most important vehicle title document. In addition, it is present on the vehicle registration certificate.

The need to find the license plate on the engine itself will appear faster only in the process of agreeing on part numbers, when you appear at the traffic police to register your car. Or during the sales process, a potential buyer wants to make sure that the engine in the car is their own.

Where can I find the engine number on a car model kit? To do this you will need the following tools:

• Small flashlight

• Chemicals to remove traces of rust (WD-40 will be good)

• Brush with metal bristles.

I must say that the number

engine on the vast majority of cars you will find on the engine itself. Usually this is the engine module itself, less often - its parts, and even less often - on removable elements. Most often, the license plate is embossed on a small metal plate, usually soldered to the engine block. Or the number may be stuck on the engine itself. They put different numbers on different vehicle models, but in the vast majority they are stamped on the surface of the engine.

Typically, you need to look for the license plate in the following places:

• On the surface of the cylinder module or on the side - in a visible place,
• Near the engine intake manifold,
• At the bottom of the hole there is a dipstick with which we check the oil level,
• Where the engine is connected to the gearbox,
• On the branch mounting module.

Be that as it may, the engine license plate can be found in other parts of the engine.

Specifications

VAZ 2114 car

The technical characteristics of the VAZ 2114 engine are quite typical for the 2113-2115 series of cars. In addition, this power unit is developed on the basis of the “eight” engine, which has declared itself to be reliable and easy to repair. The car was produced from 2001 to 2013. During this period, the vehicle received five valuable power units.

VAZ 2114 engine structure

As was said earlier, the 2114 was equipped with five different power units, which differed in power and valve mechanism. Three of them had 8 valves, and the other two had 16. The gas distribution mechanism had a belt drive. Until 2007, the engine was equipped with a simple on-board computer, which did not regulate the operation of the engine based on sensor readings. Therefore, the motorist had to regulate the processes the old fashioned way, manually. Since 2007, an ECU was installed, which, receiving data from sensors, independently adjusted many processes.

Design features of the engine.

Since the second generation had a so-called two-way electronic engine control unit, it is worth considering what electrical circuit was installed.

Electrical diagram of a VAZ 2114 car.

Main characteristics of the motor

All engines that were installed on the vehicle had approximately the same characteristics and design features. So, the motor is easy to service and repair with your own hands. Let's look at the main technical characteristics of the VAZ 2114 engine:

VAZ 2111

VAZ 21114

Video: Where is the Engine Number of VAZ 2114

The note. The approximate year of manufacture can be indicated by a number or letter of the Latin alphabet (see Table). . And on the floor there is a luggage compartment reinforcement next to the spare wheel mount.

Legend of the year of manufacture

READ Where is the wiper relay located for Nissan Almera n16

Typical breakdowns

The very first 1.5 liter engine 2114 has disadvantages:

• periodic valve adjustment;
• unreliable injection system;
• loosening the exhaust manifold nuts;
• Leaking gaskets of the fuel pump, distribution sensor of the ignition system.

The next 1.6 liter engine does not cause any particular problems for the owner, with the exception of high vibration and noise loads. The weak point traditionally remains the valves, which have to be constantly adjusted.

Adjustment of valves

The internal combustion engine from Lada Kalina 11183 was installed on the fourteenth model solely to meet Euro-3 standards. It has typical disadvantages for a linear series and is no different.

The first sixteen-valve engine 21124 does not bend the valves, the gaps in which are adjusted by hydraulic pushers. However, the belt needs to be tightened after 15,000 km due to the large number of attachments. The second and last in the line of fourteenth ICE models, ICE 21126, has increased power. In addition to typical malfunctions, if the timing belt breaks, the piston will bend the valve due to insufficient recess depth.

Frequently asked questions and their answers

The process of repairing a VAZ 2114 engine. Many car enthusiasts on forums ask the same questions. Let's try to classify all of them, and also give answers according to factory standards and recommendations.

What kind of oil should be poured into the VAZ 2114 engine?

If you rely on the manufacturer’s data, then different oil is poured into the VAZ 2114 engine, depending on the type. So, what kind of oil should you put in the VAZ 2114? If you take it for an 8 valve engine, then ideally it would be suitable with the 10W-40 marking.

If it is a 16 valve engine - 5W-30. In any case, the oil for the VAZ 2114 should be semi-synthetic.

What is the operating temperature of the engine?

Based on the manufacturer's data, the operating temperature of the motor for engines installed on models 2113-2115 is 87-103 degrees Celsius. After 105 degrees the electric fan turns on.

Where is the engine number on the VAZ 2114?

The engine number is quite easy to find. It is located on the gearbox side, near the thermostat. The engine number always has a pad on the cylinder block, which is located in a visible place.

What is the resource of ICE 2114?

The service life of the VAZ 2114 engine is 150 thousand km for an eight-valve power unit and 180,000 km for a 16-valve power unit. To extend the service life, you need to know what oil to pour into the engine, as well as service it on time. Although driving style and careful operation of the car play an important role.

Do valves bend on VAZ 2114 engines?

Of course, like in any other engine, the VAZ 2114 has a valve mechanism that bends. This often happens due to overheating, when the head bends. The valves can also bend if the timing belt breaks.

What to do if the engine does not develop power and the speed drops?

In this case, it is worth carrying out a comprehensive diagnosis of the power unit. The issue may lie either in the inoperability of one of the sensors or in the mechanics. You can find the fault on your own or with the help of professionals at a car service center.

Engine malfunctions and repairs

Disassembled VAZ 2114 engine.

The fault diagram of the 2114 motor and its modifications is quite typical. Typically, the most common ones are floating speed, tripping, pump failure, as well as others that car owners are familiar with in detail. Where certain faults are located can be determined by carrying out diagnostic work.

After 150,000 km, the engine will need a bulkhead (overhaul). Every car enthusiast can repair his engine on his own, but many do not take risks and turn to a car service center.

For the VAZ 2114, repairs are carried out by analogy with the 2108 engine, since they are quite similar. In order to replace the timing belt, you will have to fix the camshafts. The set of replacement operations includes changing the timing belt, a roller or two, as well as adjusting the valves.

To replace the water pump, you will have to fix the camshafts, just like to change the timing belt. Because the belt also passes through the pump, and therefore the process is quite complicated.

Engine design features

Initially, the engine of the VAZ-2114 was 8 valve, had a volume of 1.5 liters, complied with Euro-2 standards, and was marked 2111. In 2005, these engines were boosted:

• to increase the volume to 1.6 liters, the block is increased in height by 2.3 mm;
• Several configurations have been created - for Euro-2 version 21114-00, for Euro-3 model 21114-20 and for Euro-4 modification 21114-70;
• The crankshaft, valve system, camshaft correspond to 11183;
• The cylinder head received an enlarged combustion chamber of 5 x 8.1 cm, which increased power.

Combustion chamber of the internal combustion engine 21114
An important feature of the internal combustion engine 21114 is phased, rather than pairwise-parallel injection, used in the original 2111. Attachments have become more compact:

• catalytic collector instead of the neutralizer and exhaust pipe;
• injector ramp instead of the fuel return line.

Catcollector

At the same time, VAZ-2114 began to be equipped with engines from Kalina 11183, which have some differences from the previous version:

• the shape of the combustion chamber has been improved;
• The generator is secured with a bracket, the tensioner is modernized.

In 2008, the 2114 engine received a new M73 ECU, and in 20011, the M74 “brains” to achieve Euro-4 standards. The control became completely electronic, but for another whole year the designers corrected firmware defects until they created its final version I414DE07.

ECU M74

The next engine, 2114, was installed on the car by a subsidiary of the manufacturer AvtoVAZ, called Super-Auto, in 2009. It was the 16 valve engine 21124 of the “tenth” VAZ family with improved characteristics:

• “high” blue block (197.1 mm);
• injectors pressed into 2–5 main bearing supports, cooling the pistons with oil;
• The groove depth of the holes in the valves is 5.53 mm, which ensures the safety of the valves in the event of a timing belt break; major repairs are not required.

Blue block

The following year, the fourteenth models began to be equipped with 21126 engines from export Priors. After tuning the 21124 engine, the internal combustion engine device differs in the following nuances:

• honed cylinders, gray block;
• crankshaft pulley and timing belt with semicircular tooth;
• the weight of the connecting rod and piston group is reduced;
• there is no friction in the lower head of the connecting rod;
• candle glasses are built into the head.

Piston group 21126

The internal combustion engine uses the principle of hydraulic compensation of valve clearances; the 0.45 mm thick cylinder head gasket is made of multilayer metal. The motor is equipped for Euro-3 with a collector 11194-1203008-10 or Euro-4 with a collector 11194-1203008-00. The service life of the pump has been increased due to a new design of the oil seal and bearing, and changes to the toothed pulley.

Hydraulic compensators

Recommendations and conclusion

When the number is poorly visible or difficult to read, the car owner can carefully use weakly concentrated solvents to clean the surface. This will ensure the information content of the unit. Do not use excessive force to avoid damaging the remaining inscription with aggressive preparations.

When buying a car with a difficult to read engine number, you need to know what to do. We recommend asking the seller for supporting documents that will allow you to identify the unit. It is also worth consulting with a forensic expert, and if necessary, conduct an examination and receive an appropriate coupon from a specialist confirming the “cleanliness” of the car. Leave a comment about your experience with problem plates on internal combustion engines.

The best prices and conditions for the purchase of new cars

Credit 6.5% / Installments / Trade-in / 98% approvals / Gifts in the Mas Motors showroom

The design of the domestic automobile industry allows you to easily and often quickly find out something so necessary for the driver’s life, such as the engine number of the VAZ 2114. Let’s take a closer look at how to do this and what each value means.

It is necessary to check the information regarding where the engine number is located on the VAZ 2114, like any other car. This must be done using the official documentation that comes with the vehicle. There are always two main reasons for checking:

1. These are cases of purchasing a stolen car. This situation can be avoided - you just need to check the engine number of the VAZ 2114 car, as well as the body, for compliance with the values ​​​​in the documents. If the values ​​do not match or the numbers themselves are slightly erased, then most likely the vehicle was stolen. This recommendation applies not only to buyers, but also to sellers. The likelihood that a person will refuse to buy a car with a damaged VIN code is high. Therefore, you need to carefully monitor and maintain the condition when the situation requires it.
2. The second case is registration and deregistration. Road inspection authorities take this more seriously than future buyers, due to the fact that the VIN code is a guarantor of the legal origin of the car. In addition, there is another case when traffic inspectors need to look at the engine number of a VAZ 2114 - an operational check. It is usually carried out when a similar vehicle is reported stolen. And it is in such a situation that an acceptable state of the engine VIN code will come in handy more than ever.

Now that the question of why the VIN code of a vehicle's engine is an important element has been sorted out, let's consider all the possible places where the code is usually located.