How to replace a headlight bulb on a Volkswagen Polo sedan

On the fifth generation Volkswagen Polo, before restyling, type H4
.

These are the most common low beam lamps used in two-headlight systems. H4 has two filaments.

Standard power ranges from 55 to 60 watts. The use of higher power products is not recommended as it excessively loads the electrical wiring of the vehicle, and can also create a dangerous situation on the road by blinding oncoming drivers.

In the restyled Volkswagen Polo model, produced after 2015, type H7

.

Only one filament is used here. Type H7 is installed in four-headlight headlight systems for vehicles, with separate sources for long and short range. Here the power standard is 55 W.

There are several varieties:

• LED bulbs.
• Halogen.
• Xenon.

The cheapest and most popular are halogen. They do not require additional equipment like LED and xenon lamps. Xenon ones require an ignition unit, while LED ones use special optics.

The main disadvantage of the halogen type is that they heat up to high temperatures during operation. This negatively affects the service life and reduces the reliability of the lamp. But any of them fail sooner or later, so everyone will need knowledge of how to update low beam lamps. Choosing the right lamp will help avoid frequent repetition of this procedure.

VW Polo lamp type table

PurposePower, WType

LED low beam lamps for VW Polo

Installing LED lamps in headlights is a sore subject for many car enthusiasts. According to the requirements of the rules, it is allowed to use only those lamps specified by the manufacturer. If the LEDs were supplied at the factory, then there will be no questions, but unauthorized replacement of standard lamps may result in fines or temporary deprivation of rights. This requirement applies not only to the Volkswagen Polo, but also to any other brands or models of cars.

The reason for this strict approach is the significant difference in the design of halogen and LED devices. Reflectors and headlight reflectors are designed to work with an incandescent filament of a certain configuration and size. The position of the LEDs is completely different, it is almost impossible to adjust the beam of light to meet the requirements. Therefore, when driving, such headlights begin to blind drivers of oncoming cars, creating emergency situations, which is unacceptable.

Procedure for replacement

1. Open the hood and disconnect the negative terminal of the battery . It is best to put it on a rag that is not folded in several layers.
2. Disconnect the block from the contacts of the base. This is done very simply - we pull it towards ourselves, gently rocking it left and right. There is no need to loosen it too much - the part will quickly give in.

Remove the wire block from the lamp terminals.

Remove the headlight bulb from the headlight housing.

This operation takes no more than 15 minutes . During this time, an experienced technician will have time to change the bulbs in both headlights.

Replacing the low beam lamp on the latest Polo versions

Since 2015 , Volkswagen has been producing a restyled Polo sedan. Here, to easily remove the lamp, you will have to dismantle the entire headlight . To do this, use a Torx T27 . The algorithm of actions involves the following stages:

Using a wrench, unscrew the two screws holding the headlight.

We remove the protective cover and see the lamp holder.

The lamp holder has a convenient handle for turning counterclockwise.

Assembly is carried out in reverse order.

Volkswagen Polo sedan removing headlight glass

Volkswagen Polo Sedan polo again › Logbook › Removing headlights, front bumper, “TV” and sealing it. In the end, I did this, took the headlight with one hand by the glass, the other by the back, in the area of ​​​​clamp No. 1, and pulled it up, the clip.

Volkswagen Polo: we service lighting devices. Even though it is a budget vehicle, the Volkswagen Polo sedan is not suitable for total garage service. Removing the headlight block.

53 30 Green. Rear window defogger. 54 15 Blue. Fog lights. 184 Volkswagen Polo sedan. reverse removal, observing polarity.

Installing front spacers to increase ground clearance on a VW Polo Installing polyurethane bushings on the stabilizer.. Video report on the dynamic characteristics of the car Flip key with remote door opening for comfort Engine idle speed graphs with new firmware Graphic representation of power changes after firmware Replacing rear drum brakes with disc ones . Modifying the air intake grille of the heater water in the cabin Removing the fabric from the seats.. Using a screwdriver, pry it up and pull it off, pulling out the bumper a little. Just grab the edges with both hands, the right one in the oval area, the letter P, the left one on the other side and pull sharply, strongly, without fear of breaking it.

Volkswagen Polo Sedan Electrical equipment – ​​DMCUNMOR.RU

Topic: Removing headlight bulbs. Send by email…. Subscribe to this topic... Has anyone taken out the light bulbs? For some reason I couldn’t remove the chip with the wires; I couldn’t find any latches. It’s scary to pull something too hard in case I break it. My car: VW Polo sedan. My car: vw polo sedan. The low beam lamp on the right headlight has burned out. It took me an hour to remove the lamp itself. There the spring latch PZ is terribly figured. Bend the rubber cover from the grooves. Next, squeeze the PZ on the sides with two fingers - the PZ will come out of the grooves.

Then PZ pull the upper part down and it will finally release. We take out a lamp with a plug. Then I replaced the lamp, but I don’t imagine it’s possible to put the spring in place without removing the headlights and without touching the lamp itself. Of course, I put the PZ back, but it is clearly not in the standard grooves.

I'll be removing the headlights completely this weekend. Who knows another way? Everything turned out to be much simpler and more prosaic. Bend the rubber cover from the headlight grooves. We disconnect the plug from the lamp - the lamp remains pressed PZ to the headlight housing. It will be difficult, but it really can be done. Using the upper edge of the PZ, we pull it towards us and down - the PZ will be held in its lower grooves. We put the PZ in place. Puts a leather cover on the headlight. My main mistake was that after several attempts I started shooting in a different way, assuming that it would not be possible to remove the lamp without disconnecting the plug.

Unfortunately, it is difficult to take clear photographs in this position. Removing the headlights is very easy and quick, I took out the “corn” from the headlight block DMCUNMOR.RU.

Users viewing this topic. You cannot create new topics. You cannot reply to topics. You cannot attach attachments. You can not edit your posts.

replacing the cabin filter on a Volkswagen Polo sedan

When it's time to change

DRL lamps on the Volkswagen Polo sedan play a decisive role in the safety of both the driver and other road users. That is why they need regular monitoring and timely replacement. Many VW Polo users note the extremely short service life of standard equipment.

This is due to the frequent use of optics and the desire of the manufacturer to save on parts. Factory lamp models for the Polo sedan are formally designed for use for 2 years, but in practice their service life is 30% less. The first signs that the Polo lights need replacing:

1. Sharp “yellowing” of the shade.
2. Decrease in brightness and concentration of light flux.
3. In 50% of cases it starts flashing a minute after turning it on.

VW Polo lamp type table

Types of lamps and features of their replacement

The greatest difficulties in repairing lamps on the Polo sedan are the low beam headlights. There are many varieties: they all differ in shape, size and technical parameters. This also includes classification according to standards that are related to the content of various gases in lamps. The most well-known standards include H1, H3, H4, H7 and others.

For the Polo sedan, H4 is used. This type of car lamps has been produced for a long time. H4 is the first head light source with two filaments. Today there are many modifications of H4, differing in the structure of the gases in the flask, internal holders, spirals and shell. All parameters affect the lighting quality of the sample.

Specifically for the Volkswagen Polo sedan, you need to select H4, designed for 12 V with a power of 60 W. The luminous flux is limited to a maximum of 820 lumens for low beam and 520 lumens for high beam. Such models are produced by Phillips: model code name is 12V 60/55W H4 LL. A similar low beam lamp is sold by the brands Narva, LYNX and Valeo. A copy can be purchased in online stores at a price of 300 rubles.

In principle, you can spend money at a car service center to replace low beam lamps. The procedure will be inexpensive, perhaps even cheaper than the lamp itself.

However, what prevents you from carrying out the replacement yourself? There is nothing complicated about the repair. The main thing is to strictly follow the step-by-step instructions.

Low and high beam lamp

The sequence of actions when replacing a lamp in the head optics (using the example of the right headlight):

First you need to turn off the light source: pull off the block with the wires going into the headlight from the connector.

Access to the headlight is blocked by a rubber gasket: remove it by pulling the small protrusion on the edge.

There is a spring clip inside that hooks onto the reflector hooks.

• We put pressure on him, he clicks and moves to the side.
• Lower the lock down.

  We take out the damaged lamp and insert a new halogen.

• We assemble everything in reverse order.
• We check the functionality of the headlights.

Similarly, you can change the lamp in the left headlight.

Remove the lamp with care, without touching the glass surface. Touching the flask with your fingers leaves greasy marks, which appear on the glass during heating. To erase “prints”, you can use a cloth after moistening it in an alcohol solution.

Turn signal lamp

The second component of the Polo sedan headlight is the turn signal lamp. Most often, an Osram brand lamp with the code name PY21W 12V is installed on the model. If we decipher the designation, we get the following characteristics: voltage - 12 V, glow power - 21 W. The diameter of the sample is 25 mm, the luminous flux reaches 280 lumens. The lamp costs several times less than a halogen H4 - you can buy it in stores for 100 rubles per piece.

The procedure for replacing a turn signal lamp is even simpler than for the head light:

First you need to unscrew the socket clockwise (in the left headlight we turn it in the opposite direction).

Carefully remove the cartridge from the headlight casing.

The lamp must be turned completely counterclockwise.

Dimension lamp

Replacing the parking lamp is similar to replacing the turn signal lamp:

Scroll the lamp socket counterclockwise.

We change the lamp. In our case, we use a baseless W5W light bulb

How to remove a headlight on a Volkswagen Polo sedan? - AutoTube

To be continued... Price tag: About the design, there is no point at all in how to remove the rear headlight on a Volkswagen Polo. The updated version of the Polo will feature even sleeker LED lights. Every car sooner or later undergoes lighting repairs. You can, of course, contact a service center and pay a substantial amount of money to replace incandescent lamps, or you can change everything yourself.

It’s a different matter if the car was involved in an accident and the glass body cracked. Then replacing the flashlight will cost slightly more than buying light bulbs. One way or another, the method for removing and installing the part is the same.

Get More Stories Like This Tail light design Before you begin the procedure, you should carefully study the design of the sedan's rear light. Outside is the building itself.

Below it there are four light bulbs: All components are attached to a special metal block, which is held in place by a locking screw located inside the luggage compartment. It is easy to remove, the main thing is to catch the moment when it starts to move so as not to break it. I took it off, looked, and realized that there was absolutely no need to remove the casing in the area of ​​the lantern, but here’s why: There is just a hole in the casing for manipulating the lantern.

Operation and maintenance of VW Polo Sedan headlights

Okay, the main thing is now everything is simple and clear. Through this hole we unscrew the fasteners of the lantern itself.

It will be like this: Disconnect the power connector. There are no photos because my fingers barely got through. You need to move the connector lock in the direction the car is moving, then remove the connector itself. We take out the flashlight.

How to remove the rear headlight on a Volkswagen Polo The operation of the lamps used in the headlights of the Polo sedan depends on their brand and manufacturer’s warranties. For example, a Philips X-treme Vision low beam lamp, according to technical documentation, should last at least hours. If extreme operating conditions are avoided, the lamps last at least twice as long as stated by the manufacturer.

A new one is installed in place of the failed lamp. To replace the turn signal lamp, you need to turn its socket 45 degrees clockwise for the right headlight or counterclockwise for the left one.

All about cars, scooters and mopeds

The side light lamp is changed in the same way. To replace the turn signal lamp, you need to rotate its socket 45 degrees. The headlight assembly will be performed in the reverse order. Strange people... The light on the Polo sedan is excellent, for example, my corrector is always set to 2.

Is it really only in xenon that salvation is visible? I also disagree that I let you down. It is perfectly visible both on the highway and when I blind the oncoming light from the collective farm xenon systems.

To remove the taillight, you will need to fold back the trunk trim and lightly press on the inside of the lamp. To gain access to the taillight lamps, you must remove the protective cover, which is secured with clips.

How to remove the rear headlight on a Volkswagen Polo sedan

In this case, you will need to disconnect the block with the power wire and unscrew the two fastening screws in the upper part of the headlight using a 20mm Torx wrench. At a service station, conditions for adaptation are better, but if necessary, you can adjust the headlights yourself.

On the body of the headlamp, you need to find regulators that adjust the light beam in how to remove the rear headlight on a Volkswagen Polo and vertical planes. When starting the adjustment, you should make sure that the car is fueled and equipped, the air pressure in the tires is correct, and there is a load weighing 75 kg on the driver’s seat. The sequence of actions in this case is as follows: It should be remembered that when adjusting the headlights, the car must be located on a strictly horizontal surface.

The point of regulation is to bring the beam angle into line with the value indicated on the headlight. What does this mean? How to check if the adjustment is correct? The horizontal line on the wall can be set, for example, using a laser level.

Device management

The control of lighting devices in the car is conveniently located in one place: under the air deflector to the left of the steering wheel. A convenient classic type switch turns on the currently needed optics.

Let's consider the procedure for turning on lighting fixtures:

1. The low beam lamp on a Volkswagen Polo turns on when the handle is moved to the extreme right position. The high beam is also located in the same position, but to activate it you will have to move the left steering column switch vertically.
2. In the forward position, the high beam turns on briefly only for those moments for which it will be held manually by the driver. To constantly operate in high beam mode, move this steering column switch to a position away from you and lock it.
3. The switch lever, located on the left under the steering wheel of the car, also controls the operation of the Volkswagen Polo's turning lights. Moving it to the extreme upper position allows you to use the right turn signal, and to the lower position – the left turn signal.
4. The extreme right or middle position of the handle is a transition step for turning on the fog lights. The next step to operate the front fog lights is to pull this handle towards you until it locks for the first time. Pulling it out all the way will help to activate the rear fog lamps of the VW Polo.

Let us note something convenient for the driver: if one of the turning lamps of the Volkswagen Polo fails, the indicator for turning on the turning lights begins to blink in an accelerated rhythm. This way, the car enthusiast will be able to understand that the light bulb on the Volkswagen Polo should be replaced.

You should not put off replacing a burnt-out optical device until later. In practice, many accidents occur when the driver turns on the turn signal, but it does not work. The result is an accident, serious damage to the car, and injuries to people because of such a trifle.

To the right of the lighting control unit there is an electromechanical switch that adjusts the headlights in the Volkswagen Polo. This must be done to correctly adjust the light flux, so as not to blind people in oncoming cars while driving.

Right headlight on Volkswagen Polo

How to remove a headlight on a Volkswagen Polo sedan video | review, year

Transparent and carbon options for such protection are available. How to improve the headlights of a Polo Sedan As a rule, VW Polo Sedan owners do not have serious complaints about the operation of lighting fixtures, but something can always be improved. Quite often, owners of a Polo sedan install headlights from a Polo hatchback.

The advantages of hatchback headlights are obvious: When the high beam is turned on, the low beam continues to work. The designs for how to remove the headlight on a Volkswagen Polo are the same, so you won’t need to redo anything, unlike the wiring, which will have to be adjusted. This is due to the fact that in H4 lamps the low beam filament is half covered by a protective screen, while in H7 lamps there is no screen in the headlights of the hatch and all the light falls on the reflector.

This is especially noticeable in rainy weather, when with the stock ones you can no longer see anything, but with the Hatch ones, at least something. Ro...maN https: The quality of lighting will improve, but such a replacement requires disassembling the headlight. The VW Polo headlight is, as a rule, non-separable, and to open it, it will require exposure to temperature.

You can heat the headlight for disassembly in a heat chamber, a conventional oven, or using a technical hair dryer.

How to remove the headlight on a Polo sedan

It is important that during heating, direct heat flows do not hit the glass surface and cause damage. The disadvantage of such headlights is low brightness, so it is better to replace LEDs with more powerful ones. The connection connector in this case is the same as for the Polo hatchback, so for the sedan you will have to rearrange the wiring. Taiwanese Dectane headlights can look quite impressive on a Polo sedan. If the owner of a Polo sedan expresses a desire to install the highest quality and reliable devices on the car, he should pay attention to the headlights for gas-discharge lamps, which are intended for use on the Polo GTI.

At the same time, you should be prepared for the fact that this is also the most expensive option for external lighting. In addition to such headlights, you will need to install auto-corrector and change the comfort control unit.

The most expensive option for lighting devices is headlights for gas-discharge lamps from Polo GTI. I installed the following on the car, H7 LED lamps for low beam. After installing the lamps, the craftsmen adjusted the low beam, placed the car in front of the wall, and adjusted the light beam there.

They've been on for a year and a half now, but I mostly only drive in the city and they're always on. I don’t know what k means, maybe it’s the power of light? Checking the serviceability of the headlight elements To check the functionality of the headlight, you should use the electrical circuit diagram of the corresponding headlight.

The diagram of the right headlight unit is shown in the figure: In the diagram: According to this diagram, you can ring each lamp from the connector side. To do this, you can use a multimeter switched to the Ohm resistance measurement position.

If the device shows infinite resistance, the corresponding electric lamp must be replaced. The diagram of the left headlight unit is shown in the figure: On the secondary market, the original headlight can be purchased from rubles. Recommendations for operating headlights on Volkswagen Polo cars While operating a car, to prevent headlight failure and maintain their performance characteristics, you should: Tired of paying fines?

There is an exit! Forget about fines from cameras!

More details at the link. Sharply and strongly, chick In the photo he indicated where to grab with his hands and where to pull, with arrows Arrows Next, two at a time, how to remove the headlight on a Volkswagen Polo under the headlights, Marked with squares A, B. Use a screwdriver to pry and pull, pulling out the bumper a little. Then you need to pull the radiator grille out of the latches. I marked with a cross where there is no need to try to get into it with a screwdriver in order to bend something there. Just grab the edges with both hands, the right one in the oval area, the letter P, the left one on the other side and pull sharply, strongly, without fear of breaking it.

Headlights for Volkswagen Polo

About the third time I pulled out. Pull. Well, that’s it. We get something like the following: Here you can see the boards under the wheels So, well, now part 2, removing the TV I’ll tell you right away, it’s easy to remove, I did everything in one.

There is no need to disconnect the radiators; after removal they will hang, etc. But I would put boards under the TV, you never know, so that it is level with how it is screwed on. Immediately figure out how you will hold the hood, because then the time will come and the spacer will have to be removed.

We unscrew the 2nd bumper guides, they have 4 bolts each, and for the best you need to remember how they stood, because later, when you install the bumper, they will be a pain in the ass... the gaps will depend on how to remove the headlight on a Volkswagen Polo how you screwed them on , I pulled the bumper back and forth about 6 times and twisted them: Next, unscrew the “hardware” on top, 3 bolts, white circles in the photo: Next, we remove the left one and put it aside, and in the right there is a hood cable, there is a small “box” with a connection , we reveal how to remove the headlight on a Volkswagen Polo, and disconnect the cable: Well, everything is clear here. Next, unscrew 2 bolts, on both sides, from the TV, in the area of ​​the side members.

Next we unscrew the amplifier, or whatever it is, from the side members, 3 bolts each, in my opinion.

Replacing lighting equipment on a VW Polo

Blocklight

In this Volkswagen model, the biggest difficulty is replacing the low beam lighting equipment. To complete this task, you will have to remove the headlight. Replacement is carried out equally on both sides:

• The power supply from the head light is disconnected;
• By pulling the rubber protection tab, the boot is removed;
• The block headlight is taken out from the niche;
• The protective cover is dismantled and the light bulb is removed from the headlamp housing.
• The low beam lamp is replaced and subsequent assembly is performed in the reverse order.

When performing such work, you need to remember that the unit contains halogen light bulbs. When performing work, you should not touch the glass shell with your hands, as marks may remain, which will lead to the darkening of the light bulb when heated.

But more and more often recently LED bulbs are being installed in the low beam headlights. They provide bright light and illuminate the road well.

Replacing the light source in the turn signal is performed in the following sequence: turn the socket clockwise if the bulb is installed on the right side, and counterclockwise in the left block headlight; Remove the light bulb, install a new one and reassemble in reverse order.

We replace light bulbs as follows:

• Turn the light bulb socket counterclockwise;
• Remove the lamp socket from the housing;
• We replace the lamp and install everything in place.

Anti-fog headlight

The light bulb can be replaced using different methods: from underneath the car or by removing the headlight. The first method is performed on an overpass or inspection hole.

Replacement steps:

• Unscrew the screws securing the front part of the fender liner, bend the front wheel liner;
• Press the latch of the power supply chip, disconnect it from the lamp;
• Turn the light bulb counterclockwise and pull it out of the housing;
• Install the new light bulb in reverse order.

The fog lamp is removed if it is necessary to replace the light fixture or when replacing the front bumper. This is done using a special hook from the car kit. Replacement process:

• Insert the wire puller into the hole for adjusting the headlights, gently pull out the decorative trim, remove it, overcoming the resistance of the latches;
• Unscrew the fog light mounting screws using a Torx T-25 wrench;
• Remove the headlight so as not to damage the wiring;
• Press the latches of the block, disconnect the power from the light bulb connector on the back of the headlight;
• Turn the light bulb counterclockwise and remove it from the housing with the socket;
• Replace the new light bulb and reinstall it.

Side turn signal

• Move the side turn signal towards the front of the vehicle;
• Remove the pointer from the hole;
• We pull the cartridge, pull it out of the body;
• We replace the old light bulb with a new one and install everything in place.

Dimensions

Performed symmetrically for the left and right lights:

• Scroll the socket with the light bulb counterclockwise;
• We take out the socket and change the baseless light bulb.

The light source for the taillights changes as follows:

• Disconnect the negative terminal from the battery;
• Open the trunk;
• Pull the special cutout on the side of the upholstery towards you;
• Using a slotted screwdriver, lift up the red stopper of the connector, press the latch, disconnect the wires;
• Unscrew the fastening nut;
• Pull the lamp out of the body so as not to damage the paintwork of the car;
• Release the latches on the lamp holder and remove the platform from the lamp;
• Unlock the socket and replace the light bulb;
• Snap the cartridge between the latches;
• Reassemble the lantern in reverse order.

For those car enthusiasts who want to make their Volkswagen Polo bright, you can purchase LED multi-color chameleon bulbs. They are equipped with two diodes on the sides and are mounted in sidelights. The light bulbs shine brightly and intensely, with a power of 2.0 W.

How to remove the headlight on a Polo sedan

Next, unscrew the hardware on top, 3 bolts, white circles in the photo:

Replacing the low or high beam lamp, as well as removing the front headlight unit on a Volkswagen POLO

In general, I can advise anyone who needs it, he glues everything that he can get his hands on.: Then we unscrew 15 bolts from the wings and bumper. It took me an hour to remove the lamp itself.

Home» List of forums» Technical section on the Volkswagen Polo sedan (year of manufacture - present day)» Electrical equipment…

It looked like this: It took me an hour to pull out the lamp itself. Use a screwdriver to pry and pull, pulling out the bumper a little.

After installation, check the operation of the headlights and their adjustment. Turn the high beam adjustment servomotor in the bayonet lock and release the spherical head by pulling it out of the adjustment segment on the headlight by the body. In general, there are two of them.

I marked with a cross where there is no need to try to get into it with a screwdriver in order to bend something there.

Just grab the edges with both hands, the right one in the oval area, the letter P, the left one on the other side and pull sharply, strongly, without fear of breaking it. About the third time I pulled out. Pull. Well, that’s it. Here you can see the boards under the wheels. So, now for part 2, removing the TV. I’ll tell you right away, it’s easy to remove, I did everything in one.

There is no need to disconnect the radiators; after removal they will hang, and that’s all.

replacing the cabin filter on a Volkswagen Polo sedan

But I would put boards under the TV, you never know, so that it is level with how it is screwed on. Immediately figure out how you will hold the hood, because then the time will come and the spacer will have to be removed. We unscrew the 2nd bumper guides, they have 4 bolts each, and for the best you need to remember how they stood, because later, when you install the bumper, they will be a pain in the ass... the gaps will depend on how you screwed them in, I did 6 times here and there the bumper pulled and twisted them: Next, unscrew the “hardware” on top, 3 bolts, white circles in the photo: Next, remove the left one and put it aside, and on the right there is a hood cable, there is a small “box” with a connection, open it, and disconnect cable: Well, everything is clear here. Next, unscrew 2 bolts, on both sides, from the TV, in the area of ​​the side members.

Next we unscrew the amplifier, or whatever it is, from the side members, 3 bolts each, in my opinion. You can see them in the previous photo.

Similar questions

Arrows So, then our TV is supported on two guides, which are attached to the radiators. If the headlight glass is damaged or the reflector has become dull, the headlight assembly must be replaced. The lens and headlight mirror are glued together and cannot be replaced individually.

After installing a new headlight, it needs to be adjusted. To do this, carefully unscrew the plastic screws from the mount until they can be removed from the mounting hole. Disconnect the bracket from the turn signal lamp in the engine compartment, remove it from the headlight cutout and disconnect the contact.

Remove the two front grille screws in the turn signal slots on both sides. Unscrew the 5 screws of the front grille; 3 screws in the radiator area; one screw each on the left and right side of the front grille and remove it.

Disconnect the headlight and main light pins. Of course, I put the PZ back, but it is clearly not in the standard grooves. I'll be removing the headlights completely this weekend.

Volkswagen Polo Sedan Electrical equipment – ​​DMCUNMOR.RU

Who knows another way? Everything turned out to be much simpler and more prosaic. Bend the rubber cover from the headlight grooves.

We disconnect the plug from the lamp - the lamp remains pressed PZ to the headlight housing. It will be difficult, but it really can be done.

Using the upper edge of the PZ, we pull it towards us and down - the PZ will be held in its lower grooves. We put the PZ in place. Puts a leather cover on the headlight.

How to remove a bumper or headlight on a Volkswagen Polo sedan

My main mistake was that after several attempts I started shooting in a different way, assuming that it would not be possible to remove the lamp without disconnecting the plug. Unfortunately, it is difficult to take clear photographs in this position.