Terraco Gravitex XL / Terraco Gravitex decorative plaster “bark beetle”

Feasibility and features of application

Anti-gravel Body 950 will be needed by those car owners who often have to drive on bad roads. The make of the vehicle also matters. The fact is that on many cars, anti-gravel protective compositions are used at the stage of priming and painting the body. An example is all the cars of the Audi family, the domestic Lada Priora and a number of others. Thus, the manufacturer cares not only about protection against chips, but also properly prepares the car for operation in difficult weather conditions. In other cases, there is a need to protect the car body from chips or other damage that often occurs on the threshold, bottom or wheel arches of the car from small stones.

Anti-gravel Body 950 belongs to the category of compounds that have a certain color - white, gray or darker. The treatment consists of sequentially applying at least two layers of anti-gravel to the treated area, and the surface must be thoroughly dried before each subsequent layer. This may not be indicated in the instructions, but from user reviews it follows that before processing the surface should be sanded with 250-grit sandpaper if you are going to apply regular paint, and 350-grit sandpaper if the final surface is to have a metallic color. Some users even use sandblasting: according to them, it is in this case that the preparation will be the most uniform and of the highest quality.

If there are dents on the surface, they are repaired with putty or fiberglass. A quick and effective coating can be applied even to a bulldozer or tractor: for rust and stones, the type of vehicle does not matter.

How to apply Gravitex correctly

Its service life and efficiency depend on the correct application of the composition to the car body. Application technologies will differ depending on whether there is damage (chips, cracks, scratches) on the surface being treated or not.

How to apply non-paintable Gravitex to a surface without chipping

In order to treat a perfectly flat car surface with Gravitex, you will need the product itself, a degreaser, clean rags, masking tape and film (or paper) to protect the area that is not intended to be treated.

Please note: If the surface is not chipped, the best option would be to apply unpainted Gravitex to it, which is initially body-colored or colorless.

The process of applying Gravitex will be as follows:

1. Prepare the surface on which the product will be applied. To do this, remove any dirt from it and dry it thoroughly. Make sure that there are no chemical deposits left on the surface from detergents, and that there are no grains of sand or dirt;
2. Degrease the surface by applying a degreaser using a rag;
3. The area that will not be treated with Gravitex is covered with masking tape, film (or paper);
4. Next, Gravitex is applied in an even layer. Depending on the chosen composition option (aerosol or liquid), the details of the application technology will differ. It is important to apply it in a thin, even layer;
5. After applying one layer, wait until the composition dries and apply a second layer;
6. Next, wait until Gravitex dries, then remove the protective materials.

Important: It is recommended to operate a vehicle to which Gravitex has been applied no earlier than 24 hours later.

How to apply paintable Gravitex to a chipped surface

It is much more difficult to apply the product to a body that has defects. In this case, you should choose paintable Gravitex, which will need to be painted over after application.

Please note: It is ideal to use a computer paint selection method to match the color as closely as possible to the body color.

To apply Gravitex to a chipped surface, you will need more tools: sandpaper, putty, primer, body anti-corrosion treatment, paint, rags, masking tape and film (or paper).

The Gravitex application process is as follows:

1. First you need to clean the surface from dirt and dust;
2. Next, use masking tape and paper to cover the body parts to be painted;
3. With the help of sandpaper, body elements that have defects are polished - dents, chips, scratches, areas with corrosion, and so on;
4. The surface is degreased;

5. 
   Using putty, existing dents are repaired;

6. An anti-corrosion agent is applied to defective body elements;
7. The primer is applied, after which you need to wait for it to dry;
8. Next, the grinding stage goes through again to level the surface, after which the surface is degreased;
9. Next begins the stage of applying Gravitex. The product is applied in one even layer, after which you need to wait for it to dry and apply a second layer;
10. Leave the car for 24 hours for the Gravitex to dry completely;
11. The final stage is applying paint.

After applying the paint, it is also important to let the car “dry”. Depending on the type of paint being applied, this may take different times; follow the instructions for the paint.

( 126 votes, average: 4.52 out of 5)

Related Posts

• Diesel engine additives

• Oil filter: where is it located, how often to change and how to choose

We use it correctly, in accordance with technology

Well, and most importantly, how should the composition be applied correctly? First of all, you must find out all the details. We believe that you have already figured out the type of container and coloring. Now let's move on to the technical details.

• For example, do you need to prime before painting?
• How long will each individual layer take to dry?
• What type is acceptable for treatment with this anti-gravel?
• If you choose a pistol, what is the nozzle diameter?
• What air pressure do you need?
• What layer thickness should be maintained? Did the master dilute the composition?

Once all these nuances have been clarified, you can proceed directly to painting in accordance with the instructions. Since the entire process is usually described in some detail in the instructions, we will not repeat it.

What is Gravitex and how to choose Gravitex?

Home » Autolife » Using Gravitex and how to choose Gravitex? 584

Gravitex you shouldn't be afraid of roads

The appearance of all cars deteriorates over time due to scratches, minor dents and various types of abrasions that appear due to unfortunate stones, crumbs, sand and various objects slipping from under the wheels. A minor scratch not only worsens the appearance of the car, but will also later become the epicenter of corrosion if the car is not protected in due time.

Sometimes attempts to paint over scratches fail. If you choose the wrong paint color, the car, at best, loses its pleasant appearance. Then you have to completely repaint the bumper or the entire fender and wait for the unwanted appearance of the next stone. Such problems can be anticipated if you think about gravitex protection in time. How to deal with this difficulty using products designed for gravitex processing? You will read about this in this article.

Purpose and advantage of gravitex

A car on the road is at great risk, and it is not always visible to the naked eye. For example, stones, gravel, salt, crumbs, sand and various debris that slip out from under the wheels peel off the paint in the lower areas of the car body, on wheel arches, fenders, and even more so under the bumper. This significantly distorts the overall appearance, but does not slow down the corrosion process. Over time, the situation only becomes more complicated. This often leads to problems with the machine.

The solution to the dilemma is the means by which Gravitex treatment is carried out, the so-called anti-gravel. Their special composition allows them to take on the impact of pebbles and other solid particles, absorbing it entirely, which minimizes the risk of damage to the body. When covering areas of the body that are particularly prone to risk, these products guarantee protection of the car body and paintwork from numerous adverse factors:

• — prevent damage from impacts from gravel, stone chips, pieces of glass and various debris;
• — guarantee the integrity of the paintwork of wheel arches, fenders, sills, the lower section of the bumper and other components of the body;
• — protect particularly risk-prone areas of the body from corrosion;
• — maintain the beautiful appearance of the car;
• — due to their springiness, they reduce body vibration and noise levels.

All this requires the least amount of time, effort and money. Thanks to this, nowadays almost all car enthusiasts carry out gravitex treatment on their cars.

Structure and features of gravitex

All of the above features of gravitex coating are provided by its components. Often, gravitex is produced in the form of an aerosol or liquid (it is applied with a spray gun or a special-purpose gun). Gravitex consists of rubber, synthetic resins and organic solvents. When the surface is coated, the liquid dries and acquires the desired qualities.

When dried, the gravitex coating hardens, but remains elastic, its surface becomes finely lumpy, and its thickness is 1-2 mm. However, this layer is more than enough to combat road difficulties.

A huge advantage of gravitex is the permissibility of painting or enameling it in the color of the car body. However, this treatment is recommended when using some gravitex coatings, since it guarantees protection against corrosion. Since gravitex has a spongy structure, dampness sometimes reaches the metal of the car body. If its components are not an anti-corrosion agent or a rust converter, then applying paint to this surface when drying is mandatory.

Types of products for gravitex processing

Today the market offers a huge number of products for gravitex processing, which are indistinguishable from each other. There are a number of characteristics according to which these funds are divided into groups.

In terms of coating durability:

• — long-term gravitex coating;
• — gravitex for temporary protection.

By type of container:

• — aerosol, ready for use;
• - an aerosol can that requires the use of a specialized gun.

By color: transparent, white, gray, black.

Nowadays, “Gravitex” exists in white, gray, black colors and in the form of a product that creates a colorless film. For the gravitex coating to be effective, it must be painted in the color of the car body.

Finally, gravitex products are relatively divided into a number of groups based on the presence of auxiliary agents in their composition. In particular, gravitex can contain anti-corrosion agents, rust converters, as well as agents for better adhesion to car body coatings.

Options for using gravitex

Depending on the position of the surface to be treated, the method of applying gravitex is selected.

Steps for applying anti-gravel to painted metal surfaces:

• - clean and degrease the surfaces being treated;
• — use tape or another method to cover surfaces that should not be subject to gravitex application;
• — using a specialized gun or spray gun, apply gravitex coating;
• — remove the protective agent;
• — a day must pass before the first trip;
• - if necessary, paint with automotive enamel or varnish, following all operating instructions for these products.

Applying Gravitex to unpainted surfaces or to the bottom of the car requires a slightly different course of work:

1. - clean and degrease the surfaces being treated;
2. - apply the appropriate type of primer;
3. - if necessary, puttying is carried out;
4. - cover surfaces that should not be treated using tape or other methods;
5. — as soon as the soil has dried, apply a gravitex coating;
6. - after the gravitex has completely dried, paint it using automotive enamel and varnish.

Gravitex gun

A special gun for Gravitex is a device designed for applying Gravitex to a surface before painting. In general, it is used in mechanical engineering, in car services. In general, Gravitex is used in areas that are subject to intense mechanical influences, such as car sills and the lower areas of doors. It is also possible to use gravitex to treat the underbody of a car body, both from the outside and inside. As a result of drying, Gravitex acquires the characteristics of dense rubber, protecting the car body and weakening the impact of stones. Using this device, an even layer is applied to the surface. It has a comfortable handle and a soft, large trigger.

Gravitex protection is very necessary, and even more so very effective. Every motorist who cares about his favorite car wants it to maintain its sophisticated appearance longer. Such a person will definitely carry out this easy process, and will no longer be afraid of scratches and chips, which are almost inevitable in the conditions of our domestic roads.

Considering the state of current roads, it is virtually impossible to do without anti-gravel.

Low cost, simple application and reliability - all this is combined in gravitex, which for a long time forms armor for the body of your car from many inconveniences. Protected means armed!

Vote, did you like the article?

Loading…

Applying anti-gravel using a gun

The most common form of release of anti-gravel is in cylinders for an air gun. It creates a stronger film than aerosol, but is not as convenient to apply. Therefore, it is more often used by professionals. But such products are economical and suitable for application to a large surface.

NOVOL Gravit 600 – synthetic base

This is a liquid synthetic anti-gravel made in Poland. Easy to apply with a gun and creates an elastic film that protects the surface from moisture and mechanical stress. It is durable, does not crack or dry out in the cold.

Resistant to salts, gasoline, oil. Has noise-absorbing properties. If applied in a thick layer to noisy parts of the car, it will eliminate vibration and noise.

The texture of the product is granular, has good adhesion, and is applied evenly. Compatible with acrylic paints, easy to apply on metal, plastic, polyester putty.

Consumption is economical - a 1 liter jar is enough for a large surface when applied in 2-3 layers. Available in 3 colors: black, white, grey. The neck of the can is compatible with air guns.

Pros:

• good value for money;
• sound insulation;
• compatible with paint, varnish, plastic;
• creates a strong, durable coating;
• economical consumption;
• applied evenly.

Minuses:

• applied with a gun;
• the composition does not contain substances that protect against corrosion.

HB BODY 950 – with anti-corrosion properties

This is liquid anti-gravel made in Greece. Universal, can be used anywhere in the car. The base of the product is rubber, which creates a dense, elastic coating.

Protects against mechanical stress, corrosion, provides sound insulation, and seals cracks. Does not crack due to temperature changes or impacts.

Easily applied to metal, paint, plastic, as long as the surface is dry. But before processing smooth metal, you need to degrease it.

The result is a grainy matte surface that can be painted. BODY 950 is available in grey, white and black. Consumption is economical, although it is recommended to apply in 2-3 layers.

Pros:

• available at any auto store;
• protects against stone impacts;
• can be applied over paint;
• provides protection against corrosion;
• used not only outside, but also inside the car.

Minuses:

• wasteful consumption;
• the surface must be prepared for application;
• Used with pistol only.

DINITROL Drohnex 440/445 – chemically resistant

Liquid anti-gravel based on plastics and rubber. Suitable for processing the underbody, sills, wheel arches. Resistant to chemicals, oils, gasoline.

You can clean the treated surface with cleaning agents. Provides protection against corrosion and mechanical stress. Has slight noise-absorbing properties. It is used inside the car and for body cladding - reduces noise from raindrops.

The product is available in black, white and gray. After drying, it can be coated with paint. Suitable for plastic, metal, painted surfaces. Apply using an air gun.

Pros:

• does not crack, protects against pebbles and impacts;
• anti-corrosion properties;
• resistant to chemicals;
• you can paint the internal surfaces, body;
• Compatible with automotive paints.

Minuses:

• used with pistol only;
• the surface must be degreased before application;
• expensive.

Dr.Rubber 3-A – quick drying

A professional polymer-based product for protecting the underbody of a car. Synthetic rubber ensures the formation of a dense elastic film after drying.

It is waterproof and protects against corrosion. Resistant to mechanical stress, chemicals, and ultraviolet rays. Easily applied to metal, plastic, paint.

The product is odorless and contains no bitumen. But when using it you need to wear a respirator. Dries within an hour. After this, it does not crack and can withstand temperatures from -50° to +95˚. Suitable for underbody, wheel arches, body. Bubble Expander Technology (BET) provides effective noise reduction.

Pros:

• protection against corrosion, salts, road reagents;
• high level of noise reduction;
• applied to any surface;
• compatible with paint;
• There are no harmful components in the composition.

Minuses:

• expensive;
• difficult to find on sale;
• Used with pistol only.

The best examples of bright and anti-theft tuning

The most impressive look are business class cars, in which one part of the body has a familiar look, is beautifully painted and shines with metal, and the other part is covered with rust. Such a car invariably attracts attention and causes amazement among passers-by.

Powerful SUVs with all the attributes of a car for extreme travel in a rusty body will look as if they have recently returned from a dangerous expedition.

Types of Gravitex

You can find different types of Gravitex from different manufacturers on sale in automotive stores. Moreover, each manufacturer has its own unique formula for this composition.

Important: Depending on the composition of Gravitex, not only its protective properties differ, but also the technology for its application. This must be taken into account both when choosing a product and when treating the surface of the body and other parts with it.

Gravitex can be offered to customers in two consistencies: as a liquid or as an aerosol. The liquid is cheaper, but it is more difficult to apply to a car, since application will require a special device - a gun and a compressor. Whereas an aerosol can be sprayed directly from a can onto the body or other parts of the car.

Also, all Gravitex compositions can be divided into two large groups based on the possibility of coloring:

Paintable. After applying this type of product, you need to paint the surface

This is important to do, since Gravitex itself has the structure of a sponge, and coloring is not only aesthetic, but also necessary for protection. If you do not apply a paint layer to the anti-gravel coating, moisture will begin to penetrate through it, which will be retained, and because of this, pockets of corrosion will form on the car body;

Unpaintable

This type of gravitex contains substances that do not allow moisture to penetrate through the applied layer. This is important to remember, and you should not apply a paint coating over unpainted Gravitex, otherwise it will begin to peel off, which will lead to damage to the appearance of the car.

Undyed Gravitex comes in several colors: black, white, gray and clear. Since Gravitex does not cover the entire car body, but only some parts, the choice of black color is the most universal. White and gray are most likely only suitable for cars that are made in a similar color. As for the transparent composition, it is not very noticeable after application and allows you to preserve the original color of the body.

Depending on the manufacturer, the number of additives and the Gravitex formula, short-term formulations and long-term formulations are distinguished. Short-term Gravitex is applied, as a rule, for one season, for example, in winter. After this, it loses its performance qualities. Long-term Gravitex is able to protect the car body for a long time.

Please note: Long-term Gravitex is significantly more expensive. When choosing Gravitex you also need to pay attention to the additional properties of the composition, modeling them on your car

For example, if the car often moves along country roads, you need to choose a composition that is more resistant to mechanical damage. And for cars that are susceptible to corrosion, or that already have pockets of corrosion on body elements, it is better to choose Gravitex with additional anti-corrosion characteristics

When choosing Gravitex, you also need to pay attention to the additional properties of the composition, modeling them on your car. For example, if the car often moves along country roads, you need to choose a composition that is more resistant to mechanical damage. And for cars that are susceptible to corrosion, or that already have pockets of corrosion on body elements, it is better to choose Gravitex with additional anti-corrosion characteristics.

What is gravitex

One of the effective means of protecting the body is the creation of a durable protective layer that is resistant to various influences. Gravitex is a substance that is applied either by gun or spray to a portion of a vehicle's body to create a durable protective film that can withstand impacts from gravel and other impacts.

What parts of the body are treated with gravitex?

Gravitex should be applied to the sills, the lower parts of the doors, and the bottom and wing arches. In practice, the entire lower part of the body is treated with a protective layer.

Gravitex composition:

• rubber;
• resins;
• additives to impart anti-corrosion properties;
• solvent.

Thanks to the rubber composition, pebbles will fly off from the resulting protective film, springing back, since the rubber will add elasticity to the protective layer. Various additives will provide resistance to frost and extreme heat. The solvent will ensure strong adhesion to the paintwork coating (LPC) of the body.

Gravitex in a can for cars - instructions for use

Composition and scope

All companies producing gravitex use one basic general recipe. Each manufacturer introduces its own additional components into the composition, which allows them to advertise their compositions as the best.

All varieties are based on synthetic resins, organic solvents and rubber. After the solvent evaporates, a durable, slightly elastic and hard layer remains, protecting against chipping when hit by stones and gravel.

The thickness of the coating depends on the number of layers.

Gravitex is used for car body treatment

The use of gravitex gives:

• corrosion protection;
• high resistance to impacts from small stones;
• reduces noise;
• protects against fuel and oil, non-aggressive salts and acids,
• preserves paintwork.

In conditions of suburban use and bad roads, it is important to treat the entire body.

Types of gravitex coating

They are divided into 2 groups - dyeable and non-dyeable. Available in liquid form - in cans and aerosol cans.

Gravitex can be painted or unpainted

After applying the paintables, additional painting is necessary, because... the composition is porous and allows moisture to pass through, which can lead to corrosion.

Non-paintable ones contain water-repellent additives. Available in white, gray, black and colorless.

Depending on the composition of additives, coatings are divided into short-term - for one season or winter, after which it loses its qualities, and long-term - for several seasons.

The best aerosol products:

1. Gravitex BODY 950 is universal, available in 3 colors (white, black and grey). Old Greek company, easily available in stores.

Disadvantages: it does not stick well, so it requires cleaning and degreasing. Increased consumption.

As a replacement, for larger volumes of work, use the less expensive and non-paintable BODY 900.

1. KERRY. Russian brand of Moscow JSC “Elf Filling”. The ideal combination of price and quality. 3 colors - white, gray and black. Good adhesion and anti-corrosion properties. Dries quickly.
2. Hi-Gear. The composition is similar to liquid rubber, transparent. The mixture is expensive. Forms an even layer and dries quickly. Protects the body well.

Gravitex must be applied strictly according to the instructions.

Disadvantage: several layers must be applied.

1. Liqui Moly 6109. Contains polyurethane resins, which gives increased strength and elasticity. High adhesion and compatibility with various types of paint, low consumption.

Disadvantages: only black color, high price.

Instructions for use for cars

Working with an aerosol can is easier than using a spray gun. All work must be carried out in a ventilated box and with protective equipment - glasses, gloves and a respirator.

Sequence of work

• cover untreated areas with film or tape;
• wash the surface to be treated;
• remove rust;
• degrease the surface;
• prime;
• after drying, the soil is ground with P240 abrasive;
• Shake the can thoroughly for 2-3 minutes;
• spray 2-3 layers of gravitex

How to remove the composition

Since anti-gravel is quite resistant to aggressive environments, strong solvents are used to remove it - white spirit, pure acetone, solvent 646.

The procedure is carried out outdoors or indoors with good ventilation. Use protective equipment. Remove the gravitex with cotton swabs soaked in solvent.

How to choose anti-gravel

Anti-gravel prevents metal corrosion.
Anti-gravel is a product based on rubber or synthetic resins with additives. Used to protect the underbody of the car, bumpers, sills, boxes and other body parts. Creates a dense film on the surface of car parts.

When hardened, it resembles rubber. Thanks to its elasticity, the protective film does not crack under mechanical stress or temperature changes. Anti-gravel coating has the following properties:

• seals cracks, chips, scratches;
• prevents damage from stones and sand;
• protects against moisture, salts, chemicals;
• reduces vibration and noise;
• prevents metal corrosion.

The peculiarity of such products is that they provide strong adhesion to the surface. Compatible with metal, plastic, paints and varnishes. Most anti-gravel coatings are coated with automotive enamel on top.

There are varieties intended only for the bottom or only for metal parts, some cannot be applied to painted surfaces. Anti-gravel coatings also differ in texture, composition, color, and release form.

When choosing, you need to take into account the place of application.
Every car enthusiast needs to know how to choose such a product to protect the car, what characteristics to pay attention to.

• Anti-gravel coating in cans is applied with a brush. Cylinders for an air pistol are more convenient. These are professional, durable products, most often used in auto repair shops. For amateurs, it is more convenient to use an aerosol, which does not require additional equipment for application.
• Anti-gravel can be glossy, matte or with a shagreen effect. Gloss quickly loses its attractiveness, matte is more durable. And the shagreen effect or grain provides a dense and elastic coating.
• The location of application must be taken into account. Better is a universal anti-gravel, which is used not only for the bottom or sills. They process the body outside and inside. Such products contain additives that provide anti-corrosion, noise-absorbing and other protective properties.
• Color is important if there is no paint on top. Most manufacturers produce white, gray and black anti-gravel. There are also transparent or colored ones.

The best manufacturers

Not all products sold are effective. To make anti-gravel easy to apply, dry quickly and create a durable coating, you need to choose products from well-known manufacturers of auto chemicals.

Among them are several of the best.

• HB Body is a manufacturer of paint and varnish products and auto chemicals from Greece. Produces the best anti-gravel products based on rubber based on price-quality ratio.
• Kerry - Russian products, available in cans. Easy to apply, compatible with all body materials, creates a durable, smooth film.
• Novol is available in pistol cylinders. Creates a dense elastic coating.
• DINITROL produces various anti-gravel products with effective protection against corrosion and moisture.
• RUNWAY is a Chinese manufacturer that produces good anti-gravel in the form of an aerosol.
• KUDO is a Russian manufacturer of varnishes, car enamels, and paints.

Liqui Moly Steinschlag-Schutz

Liqui Moly anti-gravel product forms a textured surface when applied. When completely dried, the product exhibits high resistance to solvents. If necessary, it can be painted with auto enamel immediately after application, without waiting for drying.

Advantages:

• resistance to temperatures from -20 to +120 °C;
• can be applied to untreated or varnished surfaces;
• the processed part is ready for use in 10 minutes;
• Complete drying in 2 hours;
• has a pleasant aroma.

Flaws:

• It is undesirable to spray at sub-zero temperatures;
• Sometimes the gas in the can runs out, but there is still some product left.

Anti-gravel aerosol

Anti-gravel in cans is sprayed in a thin layer. It is easy to apply; any car enthusiast can do it on his own. The composition of such products is safe for metal, plastic, and paint.

They create a thin film that protects against scratches, moisture, and chemicals. To enhance the protective properties, it is recommended to apply this anti-gravel in 2-3 layers, each time waiting for it to dry.

RUNWAY RW6101 – liquid rubber

Made on a rubber base with the addition of bitumen. Provides the creation of an elastic, dense film that protects car surfaces from mechanical influences, salts, and chemical reagents.

It has anti-corrosion properties and protects against rust. The product is intended for application to the car body, underbody, wheel arches, and lower parts of doors.

RUNWAY RW6101 is available in aerosol form, 450 ml bottle. Easy to apply to any surface. The container must be shaken and sprayed from a distance of 30 cm. It dries quickly, after 15 minutes you can apply the second layer.

Pros:

• extends the service life of the body;
• moisture-proof, chemical-resistant coating;
• protects against pebbles and impacts;
• prevents corrosion and rust formation;
• It's inexpensive.

Minuses:

• contains bitumen;
• difficult to find on sale.

KUDO KU-5220 (transparent) – only for metal

An acrylic-based liquid product for protecting metal car parts from mechanical influences and moisture. Prevents chipping and corrosion.

Creates an elastic film that does not crack in the cold, is resistant to chemicals, temperature changes, and sunlight. It has high adhesion and is easy to apply to any surface. The product is transparent, not noticeable, does not turn yellow.

Pros:

• easy to apply;
• dries quickly;
• extends the service life of the body;
• suitable for painting;
• It's inexpensive.

Minuses:

• only for metal;
• it is necessary to prepare the surface;
• does not foam, the coating is smooth, it cracks over time.

ELTRANS EL-0206 – with high adhesion

9

A liquid product based on synthetic rubber to protect the underbody and other parts of the car. Creates a film that is resistant to pebbles, sand, and chemicals.

Prevents the formation of chips on the paintwork, protects against rust and corrosion. It has soundproofing properties and can be used inside a car.

Available in aerosol form in a 400 ml bottle. You can choose a color that matches the body paint. Easy to apply, dries quickly, has high adhesion to any surface. Apply in 2-3 layers, allowing to dry for 15 minutes. Completely dry within a day.

Pros:

• compatible with automotive enamels;
• protects against noise, corrosion, chemicals;
• easy to apply;
• dries quickly;
• It's inexpensive.

Minuses:

• the surface must be cleaned before application;
• Several layers are required.

Traditional methods of fighting rust

1. Acetic acid

You can dip the item in vinegar or spray the item / Photo: diz-cafe.com

2. Soda

Mix baking soda with water and run an old brush over the dishes / Photo: posuda-gid.ru

3. Citric acid

The more concentrated the acid, the more effectively corrosion is removed / Photo: ad-cd.net

4. Oxalic acid

Acid will remove not only rust, but also other contaminants / Photo: medtambova.ru

5. Hydrochloric acid

A 2% solution of hydrochloric acid will be sufficient / Photo: d6z72aalekwc3.cloudfront.net

6. Hydrogen peroxide

Peroxide is best used together with sodium salt / Photo: infokotiki.ru

7. Coca-Cola

Cola copes well with rust in the initial stages / Photo: i.ytimg.com

8. Sandpaper or foil

Food foil works well against rust on plumbing fixtures / Photo: bazazakonov.ru

Anti-gravel coating functions

Anti-gravel paint, no matter in what form it is presented, performs the following functions:

• protecting the surface of the bottom, sills, bumpers and boxes from impacts of stones, dirt and moisture, preventing the appearance of cracks and rust;
• sealing by sealing cracks and damage, which prevents their further increase;
• increase in vibration and noise insulation properties.

We also recommend that you carefully study our specialist’s article about what Movil for cars is.

Anti-gravel body 950 instructions for use

Everyone knows body 950 anti-gravel very well. This is its next generation, the next step in anti-gravel production technology. What makes them different? The first is the rubber content.

In terms of rubber content, this composition is almost identical to rubber! Almost 80% rubber is contained in this product, which allows it to achieve amazing elasticity.

For example, we applied anti-gravel to silicone paper, then removed it and subjected it to deformation. To our great surprise, we did not find a single crack; moreover, when we tried to tear it, the anti-gravel stretched like liquid rubber.

Therefore, its anti-gravel properties are at the highest level: the pebbles are perfectly springy, and dirt is not absorbed (like body 950). In addition to all this, such an anti-gravel composition, where such an amount of rubber is excellent sound insulation.

The fact is that the elastic material perfectly “removes” vibrations from the metal. Next, on a vertical surface we will look at how “obedient” this material is in work.

To apply body 951 anti-gravel we used a spray gun from the same company

Important note. To apply this anti-gravel you must use a high-quality spray gun, always with an adjustable nozzle

Guns with a direct-flow tube will not be able to properly apply this anti-gravel.

Now we will show how anti-gravel works in various situations in which we can use it. For example, sometimes there is a need to create an even seam, like factory ones.

Under natural conditions, when we take a tube with sealant, we cannot convey this seam. The same anti-gravel, due to the fact that it allows itself to be applied in a thick layer, easily copes with the task.

Naturally, this will not be a factory seam. But it will be a very beautiful and high-quality imitation. There is an increasingly common situation (in particular with Volkswagen cars) where a thick coat of sealant is sprayed on the sills.

We can use anti-gravel body 951 to repeat this structure. It is so vertically stable that we can repeat any, even large, structure. And it will remain with us in the form in which we applied it.

Finally, we will show a test for the vertical stability of the material. We will apply it to one point. Without moving the spray gun, we can estimate the thickness of the material without dripping.