Oil change in Nissan Tiida automatic transmission: full and partial, ATF type

Author: Ivan Baranov

An automatic transmission is easier to operate than a manual transmission, but requires more careful maintenance. The operation of the entire vehicle and the safety of passengers depend on the flawless operation of the automatic transmission. To do this, you need to monitor the condition of the gearbox and perform regular maintenance, otherwise repairs can be very expensive. An important role is played by changing the oil in the Nissan Tiida automatic transmission. Which oil is best to fill, how the procedure is performed - the issues discussed in this article.

[Hide]

Regulations

According to official data, the transmission fluid in a Nissan Tiida is replaced every 60 thousand kilometers. But practice shows that such an indicator can be considered only conditionally relevant, since the replacement period sometimes has to be shortened under the influence of climatic conditions. So, if in European countries with favorable road and weather conditions, you can still rely on 60 thousand kilometers, then in harsh realities it is better to reduce the regulations by half or one and a half times - for safety reasons. In addition, this will give you more confidence that the oil will not spoil before the allotted time. But this is quite possible if the car enthusiast constantly encounters the following factors:

• Temperature changes, sudden climate change (frost gives way to thaw, mud and slush on the roads, “salty winters”)
• Bad and dusty roads, frequent off-road driving, including on muddy ground after rain

In addition, the situation becomes even more complicated if the owner himself makes mistakes while driving the car. For example, he allows himself to deliberately jerk the car not only during such tests, but also constantly exceeds the speed, and thereby violates traffic rules. In addition, incorrect operation of the clutch and gearbox is possible, as a result of which the parts overheat and gradually fail, causing various breakdowns. But for the sake of fairness, it must be said that owners have to subject the car to high loads, including exceeding speed, etc. After all, they often have no other choice, given difficult weather and road factors. But it should be borne in mind that in such conditions the oil change period should be reduced to 40-45 thousand kilometers. In addition to more frequent oil changes, it is also strongly recommended to frequently monitor the volume and condition of consumables.

Sequencing

The first oil change in a Nissan Tiida should take place when the car has covered 5 thousand km. After placing the car on a horizontal surface, you need to activate the motor. When the engine is running, it should run for about 15 minutes; even at idle, the lubricant will warm up significantly, which will increase its fluidity. As soon as the engine reaches operating temperature, it should be turned off. At this stage, the car owner will need a ratchet, a socket set to “14”; using the last tool, the drain plug is quickly unscrewed. Before dismantling it, you need to place an empty canister under the tank; about 4.3 liters will flow out of the engine. lubricants However, you should not immediately remove the container; over the next 10 minutes, residual liquid will drip from the reservoir.

When changing the lubricant in a Nissan Tiida car, it is necessary to change all the important components, in particular, gaskets and filter. In addition, it should be remembered that all surfaces that come into contact with each other by means of sealing washers should be thoroughly cleaned

Attention should also be paid to the location of the filter. Before installing a new system element, you need to pour 300 grams into it

lubricant, which will allow it to be filled to 2/3 of its volume.

After all the components are in place, including the drain plug, the motorist must use a torque wrench to set the torque to 35 Nm. Only after this can you begin to fill in new lubricant. According to the manufacturer’s recommendations, the motorist must pour the substance into the neck; the lubricant volume is 4.3 liters. At the same time, we must not forget that approximately 300 gr. This fluid is already in the new filter. In total, about 4.6 liters will be required when replacing motor fluid. oils

When is an oil change required?

According to official regulations, changing the working fluid in Nissan Tiida 2008, 2010, 2011, 2013 and other years of production should be carried out after a mileage of 60 thousand kilometers. This rule applies regardless of the place where a particular car is assembled, be it Russia, Asia, Mexico or America. If the interval is not observed, this will lead to the fact that the working substance will lose its properties and will not be able to perform its functions. Difficulties will arise with shifting gears, the box will begin to vibrate, especially when starting in cold conditions. Extraneous noises and sounds may also appear, in some cases the liquid smells like burning.

Video “How to change the lubricant with filter in a Tiida gearbox”

From the video of the IngAvto channel you can learn how to replace the working fluid in an automatic transmission with a filter device.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (90.91%)

No (9.09%)

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 11 votes, average: 4.91 out of 5)

Discuss the article:

First generation (2004 – 2014)

Four-speed automatic transmission (1.5L)

• Original gear oil used at the factory: semi-synthetic
• Recommended Transmission Fluid Specifications: Dexron III
• Lubricant volume in the gearbox: 7.7 l.
• Oil change interval: 50 thousand - 100 thousand km.

Four-speed automatic transmission (1.6L)

• Original gear oil used at the factory: semi-synthetic
• Recommended Transmission Fluid Specifications: Dexron III
• Lubricant volume in the gearbox: 7.7 l.
• Oil change interval: 50 thousand - 100 thousand km.

Practical advice on choosing oil in a Nissan Tiida automatic transmission

Many novice car enthusiasts who have recently purchased a vehicle ask me what kind of oil to fill in the automatic transmission. I advise you to use only the original fluid that is poured from the factory; in extreme cases, you can use an analogue, if available.

Original oils have the technical properties that are included in them by the manufacturer. They are designed to work exactly in those automatic transmissions into which they are filled. Engineers calculate the maximum viscosity, boiling and freezing temperatures at which they can work. If you pour counterfeit goods into an automatic transmission, the automatic transmission may go into emergency mode due to a mismatch of properties and a drop in pressure in the system.

Original oil

To change the oil in a Nissan Tiida automatic transmission, you need to use the following original oil:

• Idemitsu CVT Type N. Only this lubricant is suitable for the Nissan Tiida CVT gearbox.

Transmission fluid has technical properties that increase the smoothness of the transition to a particular gear while driving and during start-up. Idemitsu coats mechanical parts with a protective film that prevents rapid wear and tear. The grease does not foam and freezes only at record low temperatures.

Write in the comments, do you fill the Nissan Tiida Idemitsu CVT Type N automatic transmission?

Analogs

If your city does not have original oil for Nissan Tiida, you can purchase analogues. All lubricants with NS 2 approval are suitable.

These oils have excellent oxidation resistance and are thermally stable. Protects metal parts from wear and deposits.

Attention! Original oil for Nissan Tiida green.

Checking the volume and condition of the oil

In a special hole in the automatic transmission there is a measuring device that is used to measure the fluid level. This procedure takes very little time and requires only attentiveness and consistency of actions from the driver. The optimal oil level is considered to be the volume that does not exceed the Max mark, and also does not fall below the Min mark on the dipstick. Any deviation from the specified norm may require adding oil, and in case of overflow, you will have to drain the excess liquid.

In addition, it is important to take into account the operating features and promptly check the condition of the oil. To do this, pull out the dipstick and carefully look at the oil print. For high mileage, it is recommended to drain a small amount of fluid and wait about an hour. During this time, sediment may appear at the bottom of the container, including metal shavings and mud deposits. In addition, other signs indicating that the oil is unsuitable include an unpleasant odor, as well as cloudiness and darkening of the liquid. In any of these cases, the oil change should be performed without any reservations or delays.

Leaks and problems

Leaks on Nissan Tiida engines are not common and occur mainly due to the lack of quality maintenance. But in any case, you need to look for the place where the oil is leaking individually.

But problems with fuel consumption and increased consumption occur regularly, especially on cars with mileage after 100 thousand kilometers. If the consumption from replacement to replacement is small, then you can try to select an oil that does not burn so badly. Or use the special LIQUI MOLY Pro-Line Motorspulung wash.

But if the engine begins to eat oil with great appetite, then most likely this indicates that the oil scraper rings are stuck. Decoking can solve this problem. Valve seals can also cause increased oil consumption. Over time, they become hard and “tan” and cease to perform their function. Replacing them should solve the problem of zhora.

Choosing oil for automatic transmission Nissan Tiida

To choose the appropriate consumables for the Nissan Tiida automatic, you need to focus on the oil characteristics recommended by the factory. At the same time, in this way you can protect the gearbox during the oil change process. So, with suitable parameters, everything is simple, because the manufacturer advises using only original oil called Nissan ATF Matic Fluid D. This product has ideal viscosity characteristics, is also well adapted for low temperatures and is designed for a long service life. The only negative is the high cost.

A more affordable oil is its analogue called Idemitsu ATF Type-J, which is practically not inferior in quality to the original.

As for the type of oil, you should choose only from two types - synthetic or semi-synthetic.

Benefits of the service

In those. Nissan system repair and maintenance is its main specialization. The range of services and level of repair work performed is identical to that declared by official dealers. At the same time, we provide a legal and reasonable opportunity not to tie the car owner to purchasing only original accessories and spare parts. Especially if technical capabilities allow the installation of contract parts or analogues.

If you need a full-fledged Nissan Tiida automatic transmission oil change, we categorically do not recommend using cheap compounds.

Each client Tech. We guarantee the quality of services. The maintenance procedure is also possible at any of the branches in the north or south of Moscow.

What tools will you need?

To change the oil in a Nissan Tiida automatic transmission, you need the following tools:

Prepare in advance:

• containers for processing;
• gloves;
• pallet gasket (if you do dismantling);
• new filter;
• rags.

All the nuances of providence

Before you start changing the oil, you should find out all the subtleties and aspects, this will help you not to overestimate your strength.

• The validity period of all auxiliary materials directly depends on the conditions of use.
• It's not worth saving oil because it doesn't pay off. The higher quality the oil, the better for transport.
• When changing the oil, attention is paid to the condition of the filters of the specified vehicle; if necessary, they are also replaced.

Timely oil changes help prevent unwanted problems from occurring.

How much to fill

At the end of the article, we will determine the optimal volume of oil to be poured into the Nissan Tiida automatic transmission. So, the 4-speed automatic transmission JF404E requires 7.5 liters of consumables. The specified volume is filled after draining the old oil, as well as cleaning the gearbox from various deposits, including metal shavings. Cleaning can be done using a flushing agent that is circulated throughout the automatic transmission with the engine running. Then the used flushing is removed from the box, after which 7.5 liters of liquid are poured. Its level is adjusted to normal using a dipstick.

Customer Reviews

Union Motors technical centers have a 5-star Yandex user rating since 2021!

We thank all Union Motors clients for their high rating! Thank you for being with us!

Online ratings of technical centers:

Union Motors Berezhkovskaya

Union Motors Medvedkovo

291017 Well done guys!!!

... I signed up for chassis diagnostics, the silent blocks of the front arms and the front and rear stabilizer bushings were torn, it was already late and it was decided to reschedule the next day, the inspection master found a convenient time for me. The next day I came to replace worn out parts...

Read the full review of Union Motors · Comments 1 · Like

Read all reviews

Complete replacement of transmission fluid in automatic transmission

A complete change of transmission fluid in a Nissan Tiida is identical to a partial one, with the exception of the last steps. After you pour oil into the machine, your actions will be as follows:

1. Remove the return hose from the cooling system.
2. Extend it and insert the free end into a five-liter bottle.
3. Call your partner and ask him to start the Tiida engine.
4. Black waste will pour into the bottle. Wait until the liter is drained.
5. Stop the engine and add as much as drained.
6. Start the engine again and repeat the procedure until clear liquid flows out.

Add more, reinstall the hose and start the car. Warm up the automatic transmission and drive the car. Check the level and top up if necessary.

Write in the comments whether you have already done a complete change of transmission fluid in a Tiida automatic transmission or have used the services of service centers?

Oil filter

To unscrew the filter element on a Nissan Tiida, it is advisable to have a special puller. If it is not available, you can try to unscrew the filter using improvised means.

For these purposes, you can use, for example, an old alternator belt, a regular belt, a bicycle chain or a simple screwdriver.

Unscrewing the oil filter using improvised means. This method will allow you to drain as much of the oil as possible, after which you can proceed to further actions. The main thing is not to forget, everything that we unscrewed must be put back in place.

Before changing the oil, many people fill in flushing oil, but this should be done if:

• You are the first and only owner of your car;
• Have you always changed your engine oil on time (or better yet, more often);
• You are confident in the service center where the work was carried out (the service technicians did not cheat by not changing the oil at all or replacing it with their own, cheaper one);
• On a long journey you never had to top up anything.

Functions of automatic transmission oil in a car

The main function of transmission fluid is to lubricate the surfaces of parts to reduce friction between them. In addition, the oil controls the temperature in the engine.

The main tasks of gear oil include:

• reducing the friction force between the surfaces of the nodes;
• protection of parts from corrosion;
• temperature regulation and system cooling.

After a certain time or mileage, the lubricant gradually loses its properties, which indicates the need to replace it with a new one.

You can understand that the transmission fluid requires replacement by the following signs:

• increased fuel consumption;
• uncharacteristic sounds from the gearbox;
• problems when starting the engine for the first time;
• poor response of the selector to driver movements;
• violation of the smoothness of gear changes;
• reduction in vehicle dynamics.

Changing the automatic transmission oil in a Nissan Tiida is necessary in order to eliminate the negative impact of the lubricant on the components of the unit and extend the life of the machine.

How to properly evaluate quality

There are a couple of specifications for this liquid. The most common brands were invented in special laboratories of General Motors Co and Ford. The first marking is ATF, which means transmission oil. This type of lubricant is used for the machine. On the market they have the following markings: Dexron, Mercon and Type F. In the special documentation for the car, the brand of fluid for use should always be indicated. In order to maintain the operation of the gearbox, you must adhere to all requirements.

In certain situations, it is necessary to change a fluid with similar properties. For a complete picture of what oil should be used, it is worth knowing the general principles and labeling. Automatic transmission oil performs certain functions:

• friction between parts that are in close contact is reduced;
• the surface is protected from rust formation;
• cooling of parts.

Taking into account the temperature regime, when choosing oil, high-quality petroleum products or synthetics are used.

Various types of lubricating fluid have differences in color, smell, and structure. If the box was recently made, you need to take out the dipstick and very carefully examine the color and smell of the oil. If there is a strong change in color and odor over the period of operation, this indicates that a problem may occur. When buying a car with an automatic transmission, the oil should have a transparent appearance, and the smell of burning should be completely absent.

Nowadays, experts strongly recommend using Nissan ATF Matic Fluid J oil. Characteristics of this oil:

• density – 865;
• hotness at 40 C – 33.39;
• kinetic hotness at 100 C – 7.39;
• viscosity degree – 168;
• flash – 246.

Changing the oil must follow all the rules. In order not to encounter problems when using the car, fill in the original lubricants.

To determine whether the oil in the car is of high quality, drop a little oil from the dipstick onto a paper napkin; if the liquid is easily absorbed, this indicates quality, and also that there are no unnecessary inclusions.