Location of the engine number on the VAZ 2110: carburetor and injector

Engine 1.5 l 8 valves carburetor

The ancestor of the ten family, well known to car enthusiasts from the eighth model Lada. Easy to maintain and repair, as a result of a thoughtful, logical layout, dozens moved under the hood, with all the features, including the location of the unit number. The plate is hidden in the upper part of the end side of the block under the carburetor and cannot be seen during a quick inspection. This place is characterized by oil ingress when topping it up, leaks from under the sealing rings of the distributor, fuel pump gaskets, antifreeze when replacing the thermostat. Metal corrosion also takes its toll. The motor was installed on the 2110 from 1996 to 2000. The placement of the block number has not changed.

Briefly about its characteristics.

The carburetor four-cylinder engine with a volume of 1 5 liters developed

• Power 72 l s (53 kW);
• torque 104 Nm;
• up to 100 km/h - 14 s.;
• Consumption - 7 6 l/100 km.

Geometry check

Here are four main types of measurements that will allow you to make sure that the car has not been in an accident and has the parameters you need:

1. Reconciliation of diagonals. Before proceeding with detailed calculations, you should make two simple measurements that will immediately identify the problem. The car needs to be measured diagonally on both sides. If the measurement results coincide (with an accuracy of a millimeter), this will mean that the body as a whole has the correct shape. But we should not stop at these two dimensions.
2. Checking the height of the racks. To take this measurement, you need to measure the height of the racks in four places. It is important to take measurements from the front and rear, as well as from both sides of the machine. The four indicators must match.
3. Identification of a distorted roof plane. To find out if your car's lid is in place, take measurements from the door diagonals. You need to measure from the bottom rear corner of the door to the top front corner, and vice versa. If the indicators coincide on both sides, good. Just in case, it’s worth checking the roof diagonals.

1. Determining the correct location of the front glass. Contrary to popular belief, even if the windshield fits correctly, its geometry can be distorted. Therefore, be sure to compare the lengths of the diagonals of this part.

As a rule, problems with mismatched machine parameters arise after road accidents. However, this does not happen 100% of the time.

Welding or other repairs that involve heating the metal can affect the physical parameters of the vehicle. Therefore, each time take the above measurements after the car has been to the auto repair shop.

Engine Number VAZ 2110 8 Cl

The VAZ 2110 engine uses gasoline from AI-92 to AI-95 as fuel. The location of all VAZ 2110 engines is different, both in terms of power measurement and volume. Now we will carefully tell you about all the main engines that we encounter under the hood of the VAZ-2110.

The 10 was originally developed on the VAZ-2108 platform, so the parts and components are likely to be similar. The first 2110 engines were very similar to the 1.5-liter VAZ-21083 engines with 8 valves and a carburetor. But there were some differences in the engine settings. A photo of the 8-valve carburetor engine of the VAZ 2110 under the hood of the car is just below.

In fact, visually, the engine is not enough, how does it differ from the “eight-digit” engine.

The parts are probably interchangeable. These engines received an order of 110 at the start of sales in 1996. The engine was installed on the car before 2000. The built-in 4-cylinder engine had a metal block and a duralumin cylinder head. The timing belt uses a timing belt. This version of the motor, when the belt breaks, in other words, the valve jump does not bend . The camshaft has an overhead position.

The four-stroke carburetor engine was not environmentally friendly, moderate fuel consumption and the highest reliability. The carburetor had a number of advantages, such as maintainability, simplicity of design, and the ability to repair independently and omnivorously. But there were also disadvantages, such as unstable operation, obstacles during cold starts, excessive fuel consumption and other problems with carburetor power units. Further details Properties of the VAZ-2110 engine .

Engine number VAZ LADA 8 cl. Grant, 2114, Nissan ON-DO, Kalina, 2109, 2108, Largus

• Volume. 1499 cm3
• Number of cylinders 4
• Number of valves 8
• The cylinder diameter is 82 mm.
• Move. 71 mm
• Power. 72 hp (53 kW) at 5600 rpm
• Torque. 104 Nm at 3800 rpm
• Compression ratio 9.9
• Supply system. carburetor
• Acceleration to 100 km/h 14 seconds
• Maximum speed 164 km per hour
• Average fuel consumption is 7.6 liters.

The next engine that appeared under the hood of the VAZ-2110 was an injector. By and large, this is the same engine with a displacement of 1.5 liters, unfortunately, without a carburetor. The engine received the VAZ-2111 index. Our client left the main parts of the unit, the connecting rod and piston group, the lubrication and cooling system remained the same, but there is a distributed fuel injection system, another air filter and spark plugs. Photo of the 8-valve VAZ-2110 injection engine below.

The use of injection gave the engine some energy, making it more economical and environmentally friendly. The timing belt remained with the drive simulator, during which the valves did not bend. The properties of the VAZ-2111 injection engine will be discussed in detail later.

• Volume. 1499 cm3
• Number of cylinders 4
• Number of valves 8
• The cylinder diameter is 82 mm.
• Move. 71 mm
• Power. 76 hp (56 kW) at 5600 rpm
• Torque. 115 Nm at 3800 rpm
• Compression ratio 9.9
• Supply system. distributed injection
• Acceleration to 100 km/h 14 seconds
• Highest speed 167 km per hour
• Average fuel consumption is 7.3.2 liters.

After the injection of the injector at AvtoVAZ, it was decided to develop 16-valve engines, which were also necessary to increase the power, efficiency and dynamics of the VAZ-2110. This is how the 2112 . From the previous 2 8-valve 1.5 liter engines. This 16-valve engine has a more complex cylinder head design and has two camshafts. Changing the timing belt is now difficult because there are now two camshaft pulleys and rollers (tensioner and bypass). It was very important to connect our client with the elements that were left behind. Photo of the design of the VAZ-2112 engine toothed belt drive, see below.

Where is LADA 2115 VIN

• Volume. 1499 cm3
• Number of cylinders 4
• Number of valves 16
• The cylinder diameter is 82 mm.
• Move. 71 mm
• Power. 93 hp (68 kW) at 5600 rpm
• Torque. 128 Nm at 3800 rpm
• Compression ratio is 10.5
• Supply system. distributed injection
• Acceleration to 100 km/h 12.5 seconds
• Maximum speed 180 km per hour
• Average fuel consumption is 7.2.7 liters.

The most successful in design were the VAZ-2110 engines with a displacement of 1.6 liters. Now their modifications are actually installed on our client, the Lada models that are sold today remain. These are the 8-valve VAZ-21114 and the 16-valve VAZ-21124 . In fact, the main engines for these units are the same 1.5-liter engines. The recipe turned out to be simple enough to increase the height of the cylinder block by 3.2.3 mm and increase the piston stroke from 71 mm to 75.6 mm. At the same time, the diameter of the cylinder, that is, the piston, was the same 82 mm.

Unfortunately, to avoid valve failure, the 1.6-liter pistons are now recessed. because when the timing belt breaks in 1.6 liter engines, the valve does not bend . Some competent motorists with a complete overhaul of a 1.5-liter engine install new pistons with recesses from a 1.6-liter engine. The piston is the same size. This solves the problem of bent valves, but compression is slightly reduced due to the different piston head shape. Photos of a piston with notches for a VAZ-2110 engine valve have been added.

VIN code VAZ-2110

All cars of the “tenth” family were equipped with a factory plate with markings. Each vehicle by law has an identification number.

We specifically noted the data in the photo. This is our editorial VAZ-2110 for testing! They even washed the engine before taking photos.

Well done! The following two tabs change content below.

The body number is located on the car body and is duplicated in the documents.

• On the VAZ-2110, the body number is located under the hood on the pillar on the right.
• It is also repeated on the spare tire bracket in the trunk. The number is on the right side of the counter. Number on the luggage compartment floor reinforcement.

Ways to clear a table

Number tables often become dirty and corroded. Do not use coarse sandpaper for cleaning. The exception is very fine sandpaper (2500 - 2000).

Gasoline is often used to clean the table. The printed information will become more contrasting over time. For convenience and speed of the procedure, a dish sponge is usually used. When cleaning, be careful to preserve the metal. When the engine, car body, or VIN tables are corroded, problems often arise and more time is required to carry out registration procedures.

Car body and engine numbers, VIN code - basic information identifying the vehicle. Number combinations must match the data in the documents.

Source: tut-nomer.ru

What to do if the engine is dirty and the license plate is not visible

In unfavorable operating conditions of the vehicle, the engine becomes dirty. The inscriptions become invisible if you do not clear them. Rust eats away the metal to such an extent that the embossed information turns into a mess of incomprehensible symbols.

If the car's engine code or data plate is simply dirty, then you need to take a metal brush and clean the dirty area. If the dirt does not come off, then it is necessary to use acetic acid or an alcohol solution. WD 40 often becomes a car owner’s assistant in overcoming dirt and rust. Use a WD-ashka to remove dirty deposits.

To prevent corrosion, it is necessary to lubricate the surface with the symbols with lithol. Many will say that then dust will stick to it faster. But lithol will save you from rusting and eating important symbols.

Decryption features

The information table and VIN code of a VAZ car allows you to find out the following information:

• the manufacturing plant where the vehicle was produced;
• model;
• body number;
• year of issue;
• maximum permissible weight;
• engine model (the technical features of the “ten” will depend on it);
• the maximum weight that is allowed for the car together with the trailer;
• numbers of original spare parts installed initially;
• load allowed on the axles used (must be indicated separately, because the permissible value is different);
• modification;
• car version.

The Lada 2110 model is designated by a letter of the Latin alphabet or a number. All information specified above must be placed on the certificate issued for the vehicle.

How to check the engine number when purchasing a used car

To independently check the code, it is enough to study the identification table and the main documents issued for the vehicle. This may be a registration certificate or PTS. Next you need to follow this procedure:

• inspect the motor number on its body;
• correlate the symbols on the body of the power unit with the symbols indicated in the vehicle registration certificate;
• if there is none, compare the information with the number indicated in the vehicle passport;
• If we are talking about American cars, the number on the engine may not appear, in which case it must be indicated in the PTS.

Separately, it is necessary to check whether the car is listed as stolen, and whether someone has tried to rename individual combinations of symbols. It is also important that all part numbers correspond to the designations specified in the relevant documentation.

General principles of decoding

Knowing where the body number for the VAZ 2110 is located, you must also take into account the specified information:

• code information about the automobile plant where the car was produced;
• VAZ model;
• the year the vehicle was produced;
• car body number;
• the model of the power unit, and the technical parameters of the domestic car directly depend on it;
• weight that is allowed according to the maximum indicator;
• permissible weight of the vehicle with trailer;
• the load that is allowed on the axles used (indicated separately, since the permissible value will be different);
• numbers of spare parts that were originally installed;
• vehicle version;
• modification option.

The model year of the vehicle is indicated by a number or a Latin letter.

The above information must be indicated in the certificate issued for the VAZ 2110.

Fact! Until 1982, the VIN code consisted of 11-15 characters, but currently it necessarily includes 17. Separating signs are usually embossed in the form of 5-pointed stars. Moreover, each sign must be up to 10 millimeters high and they are placed between two stars. On VAZ-2110 cars, the VIN code must be applied using the impact method to preserve the readability of information for a long time.

Taking into account the location of the body number, engine, VIN code on the VAZ 2110, experienced drivers can quickly find out complete information about the vehicle.