Removing side window deflectors: how to do it?

How to remove the air deflector: step-by-step instructions

1. Removing the deflector on VAZ cars: step by step
2. Ford Focus 2
3. Chevrolet Cruze
4. Renault Logan, Sandero
5. Kia Rio

It would seem, why suddenly remove the air duct deflector. The need for this may arise for various reasons. For example, it may simply fail, in which case it should either be repaired or replaced. To improve the interior, some people purchase deflector grilles from other car models and install them. Our goal is to tell you how to remove the air duct deflector in order to carry out the desired operations. The process will be examined using the example of different VAZ models. Here you will also find instructions on how to remove the air deflector on foreign cars.

Removing the deflector on VAZ cars: step by step

The most common problem faced by owners of VAZ cars is the breakdown of the plastic curtains on the central deflector, as well as the air intake clogged with debris and dust.

On the VAZ 2106
The rotary air duct deflectors on the VAZ 2106 are round and are located on top of the instrument panel. It is held in place by three plastic snap fasteners.

Layout of deflectors on the VAZ 2107
On the classic, there are two deflectors (33) in the center, separated by a plastic partition. They are inserted into the sealing rubber inside and held in place by compression. Plus there are small floating clips on the top and bottom. Easy to remove. At the attachment points they are pryed with a screwdriver and pulled out. The side deflectors (5) are removed in the same way.

On old-style cars VAZ 2110, 2111, 2112, everything is also very simple. The grille is held in place by latches, so you just need to pry the grille with a screwdriver and it will snap off. You must first remove the plastic cover on the slider. The deflector on new cars cannot be dealt with so easily, since the grille is additionally fixed with screws. To remove it, you will need a Phillips and slotted screwdriver.

1. The fasteners that need to be unscrewed are located behind the plastic cover.
2. Pry it off with a flathead screwdriver.
3. Under the insert you will see two screws, you need to unscrew them with a Phillips screwdriver.
4. After removing the screws, simply remove the grille; it is no longer secured in any way.

Video: dismantling deflectors on a VAZ 2110

On the Lada Granta the process is trivial. The air duct deflectors are simply pulled out of their seats.

Video: removing deflectors on Lada Granta

On Priora and Kalina, air duct deflectors can also be removed without additional labor costs. On Kalina, for example, they are attached with two screws: from the top.

Top mount

Lower mount
However, Lada Vesta will throw up a lot of surprises in this sense. Since the air duct deflectors are additionally fixed there, and the screws of the side air ducts are located in hard-to-reach places.

To remove the side deflectors, remove the cover covering the fuse box on the left. It can be secured with a nail with a black plastic cover.

Video: dismantling the fuse cover on the Lada Vesta

Ford Focus 2

You will need a flashlight and two screwdrivers of suitable diameter. The deflector is secured using two fasteners. To loosen the fixation, you need to insert two screwdrivers between the fastening partitions, thereby loosening them. Then simply pull out the deflector.

Video: completely removing the deflector on a Ford Focus 2

The rings are even easier to remove. Look at the video.

Video: dismantling the decorative rings of the deflectors on a Ford Focus 2

Chevrolet Cruze

On this car, dismantling is simple, everything is attached to clamps and, when removed, is pryed off with screwdrivers.

Video: procedure for removing deflectors on a Chevrolet Cruze

Renault Logan, Sandero

The air duct deflectors are mounted in the same way as on our Lada Granta. They are even interchangeable. They are removed in the same way: by simply pulling them out of their seats.

Video: how deflectors are attached to Renault Logan

Kia Rio

But with this model you will have to seriously tinker. Since the deflector is attached to screws that are hidden by the visor. It must first be removed.

The tools you will need are Phillips and slotted screwdrivers, a flashlight and a construction spatula.

The process involves some combination of activities. Watch in detail how this work is done in the video.

Video: removing the instrument panel visor on a Kia Rio

;

Only then can you remove the central deflector. It is attached to pistons and screws. Two screws at the top, two pistons at the top and one at the bottom. After the deflector is removed, you need to disconnect the plug.

Before dismantling the left deflector, remove the left panel and the panel under which the fuse box is located. The deflector is attached to the side with two self-tapping screws. Before dismantling the right panel, open the glove compartment and remove the right panel, unscrew the screws. Now, by prying with a screwdriver, you can remove the deflector.

Video: dismantling the central and side heating deflectors

This is how the air duct deflector is removed on different cars. Of course, within one article it is impossible to give complete instructions for all car models. From all of the above, we can conclude that the amount of work that needs to be done to remove the air duct deflector is not the same. In some cars, the deflector is removed simply by pulling it out (Renault Logan), in others you have to remove the dashboard or other large elements (Lada Vesta, Kia Rio).

Replacing side deflectors

Now let's look at how to remove the VAZ 2114 interior air deflectors located on the sides (and this is quite simple to do - they are attached without the use of screws at all, but are held in place by eight latches). The first 4 of them are located on the outside - two in the upper part under the overlay and two in the lower part.

In order to squeeze them out, you should use a thin screwdriver or a strong knife blade. Also, in order to avoid scratches on the surface of the reflector, you should place a soft cloth under the instrument. Once the outer latches are open, all that remains is to disconnect the deflector housing from the duct body (which is held in place by the remaining four latches) and remove it.

Installing the reflector in place is done in exactly the same way, but in the reverse order. A very useful action before installation (both in the case when replacing the heater deflectors of a VAZ 2114 with new ones, and when installing old ones in their original place after cleaning) would be to glue the entire perimeter of their body with a noise-insulating material, which at the same time plays the role of a seal (for example, modelin or its analogues).

When opening the side reflector latches, you should place a soft material under a screwdriver or knife - this will protect the case from damage and scratches.

How to remove side window deflectors yourself quickly and correctly

How often do you have to deal with bad weather on the road? Given the peculiarities of the domestic climate, probably quite often. If so, you are of course using deflectors, which not only help protect your side windows from small stones and dirt, but also allow you to open them slightly when it rains, eliminating the possibility of moisture entering the car, even in strong crosswinds.

Deflector - types and principles of operation

The main task of the deflector, or as it is also called the “cut-off”, is to prevent air flows carrying dirt, small stones and moisture from entering the car interior. This task is accomplished by using them to create a certain aerodynamics of the car body, which does not allow dust flows to get inside the car.

Such a “cutter” is always installed in the upper part of the side window, thereby creating a semblance of a visor, thanks to the shape of which dirt and dust do not enter the cabin not only from the front, but also from the sides. Well, in addition, it ensures uniform ventilation of the cabin even during high-speed driving, which is usually accompanied by strong air currents entering the cabin.

Depending on the cost of the products, there are 2 methods of attaching them: based on double-sided tape (cheaper) or plug-in (more expensive). The method of fastening also affects the safety of the car's paintwork - cheaper products often spoil it.

Preparing to dismantle the deflector - necessary materials

Before removing the side window deflectors, you need to prepare the necessary materials for this. As we have already said, the methods for dismantling the cutter will vary significantly, depending on the method of its attachment. However, first things first.

Fastening deflectors using double-sided tape

If the deflectors on your car are glued, then to remove them you will need a whole set of tools:

• construction, professional or, as a last resort, an ordinary household hair dryer;
• a sharp stationery or so-called “construction” knife;
• an ordinary fishing line, but definitely strong, or the so-called “construction string”;
• a solvent, but not just any solvent, but a special one - white spirit, the so-called Kalosh alcohol or, in extreme cases, ordinary medical one; such solvents are neutral to rubber products (rubber products) and paint and varnish coatings of cars;
• a plastic school ruler or the same scraper for removing ice;
• rags, or even better, special fiber, which is used in professional car washes, these do not leave streaks and lint.

We figure out how to remove the deflectors on a VAZ 2114

Very often, car enthusiasts are faced with the following question: how to remove the deflectors on a VAZ 2114? It occurs as a result of the fact that when they are handled carelessly (for example, when trying to clean them with force), they break or are pressed inward. How to correct this situation will be discussed in today’s article.

What are deflectors and the reasons for their failure?

Before considering the main topic - how to remove the air ducts of a VAZ 2114 and their nozzles, you should first briefly talk about what they are.

The deflector (otherwise called an air duct nozzle or air deflector) is designed to reflect the flow of air moving from the stove through a special channel (air duct) and deflect it in the desired direction (in the direction that the driver or passenger wants - for this there is the possibility of deflecting the deflector guides ).

Due to the peculiarities of their design and location, side deflectors are often damaged as a result of mechanical stress (for example, when accidentally pressed). In addition, they can break if you try to clean them with a hard object (screwdriver or knife) using significant force.

How to dismantle central deflectors and install new ones

Removal of deflectors may be necessary in one of the following cases:

• they are clogged and require cleaning;
• a deeper cleaning of the system with removal of the air ducts is necessary;
• the deflectors were pressed into the air duct;
• The deflectors are broken and need to be replaced.

In any case, whatever the reason for dismantling them, it is quite simple to do and does not require a lot of free time or special tools. The entire process of removal and reinstallation takes place in just a few steps, the first of which is removing the dashboard panel.

In order to do this, you need:

• disconnect the battery;
• remove the receiver/radio tape recorder, disconnect the cable harness from it;
• remove the center console screens;
• remove the cigarette lighter by disconnecting the harness of suitable wires;
• remove the ashtray light bulb and disconnect the wires that go to it;
• remove all protruding buttons and adjustment knobs (to do this, carefully pry them off with a screwdriver);
• Use a Phillips screwdriver to unscrew the screws holding the instrument panel panel (one each on the left and right);
• Unscrew two screws located above the dashboard and two screws located under it;
• pry and remove the rear window heating plug;
• Unscrew the self-tapping screw located under this plug with a Phillips screwdriver;
• move the panel back and to the right;
• disconnect all blocks with wiring harnesses from the switches and on-board computer.

Once the panel is completely detached, the deflectors themselves can be removed. To do this, you need to unscrew the three screws responsible for fastening the central deflectors. One of them is located under their body, the other two are on its sides. After this, all that remains is to remove the deflector, clean it (if necessary), and install it back.

Assembly of the front panel and its installation are also carried out according to the above described scheme, but in the reverse order.

Before installing the deflectors in their place, it will be very useful to cover their perimeter with sound-absorbing material, such as modelin.

Replacing side deflectors

Now let's look at how to remove the VAZ 2114 interior air deflectors located on the sides (and this is quite simple to do - they are attached without the use of screws at all, but are held in place by eight latches). The first 4 of them are located on the outside - two in the upper part under the overlay and two in the lower part.

In order to squeeze them out, you should use a thin screwdriver or a strong knife blade. Also, in order to avoid scratches on the surface of the reflector, you should place a soft cloth under the instrument. Once the outer latches are open, all that remains is to disconnect the deflector housing from the duct body (which is held in place by the remaining four latches) and remove it.

How do I remove old push-in side window visors from a car?

All you need is a screwdriver and 10 minutes of time. Using a tool, you need to pry up the outer clamp, which acts as a spacer, and move the deflector down. Some models are fixed with mounting screws. If any exist, then their dismantling is carried out first.

Here, in fact, is all the information that answers the question: - How to remove side window visors from a car? For additional information, you can read other how-to guides that describe how to remove window deflectors from your car in the shortest possible time without damaging the paintwork.

Source

Removing the deflector on a Volkswagen

VW Polo Sedan — How to remove the side heater deflector (air duct)

Removing and installing side heater deflectors, as well as chrome edging (frame) on a car...

Central air deflector Passat B6

Removing the central air deflector of Passat B6; B7 and damper repair + a small bonus at the end..))

“Removing the side window blower deflector on a Volkswagen Polo

Repair of air duct deflector Passat B5

Repair of air duct deflector #Passat B5 ============================================ ===== By connecting to the affiliate program through my link...

Repair of air duct deflector Passat B5

Repair of the Passat B5 air duct deflector.

Replacing the backlight lamp in the deflectors of Passat B5/ Passat B5, Audi, Skoda.

Replacing the backlight bulbs in the air intake deflectors on the Passat B5. If our videos were useful to you and you...

LIGHTING for deflectors Passat B5.Air vent light Passat B5. #RedWind

replacing light bulbs with LEDs!!(((support the channel in its development sb.4276 8550 1249 4981))))!! #RedWind#autorepair#PassatB4.

VW TIGUAN Removing the dashboard detailed disassembly

deflector repair

the deflector is broken how to remove the deflector the stove does not heat the interior heater rfr cyznmltaktrnjh #deflector repair…

Skoda Octavia A7 — How to remove the side heater deflector

Video review of dismantling the side heater air duct on a Skoda Octavia A7. Detailed repairs - your...

Watch the video “Removing the deflector on a Volkswagen”.

Tips for self-repairing cars based on the personal experience of car owners

This section contains video clips on the topic “Removing the deflector on a Volkswagen” in which car owners share the intricacies of repairing their cars in garage conditions,

without involving specialists from official car services

For those who are accustomed to using regular printed publications, we recommend purchasing car repair manuals in the largest stores in Russia and Ukraine

Automotive literature stores:

krutilvertel

- Electronic books of printing quality in PDF format
autodata
- Online store of the Legion-Avtodata publishing house
avtoliteratura
- Specialized online store of automotive literature Autoliterature
autoinform96
- literature on the repair and operation of cars in Russia and Ukraine

Dismantling of air ducts

Sometimes, in addition to removing the deflectors, you also have to remove the air ducts themselves (this may be necessary if they are damaged or severely clogged).

In order to dismantle them, you need:

• remove the deflectors (how to do this was described above);
• remove the dashboard by unscrewing the fastening screws;
• disconnect the side air ducts (left and right) by unscrewing two screws securing them to the central air duct;
• disconnect the central air duct by unscrewing three screws - one in the center and two at the edges.

After the air ducts have been cleaned or replaced with new ones, their installation and assembly is carried out according to the specified scheme, but in the reverse order.

Removing deflectors: how to remove wind deflectors correctly

Side window deflectors, which protect the driver and interior of the truck from splashes (precipitation and windshield wiper), cigarette smoke and ash, can sooner or later fail. Although it is not uncommon for a windshield to serve faithfully for 10 years or more, the time comes to change it. In our material we will talk about how to properly remove deflectors from a truck window.

Please note that the visor should be removed based on the method of its installation. Dismantling a deflector glued to tape will be different and will take much longer than one that was attached under a sealing rubber band.

Dismantling windshields mounted on adhesive tape (using the adhesive method)

Before you remove window deflectors installed with industrial tape, you should prepare. Bring a stepladder, because you will have to work at the level of the visor. Another option is to remove the entire door and work on a horizontal surface, but this is more troublesome.

For dismantling you will need:

• hair dryer (a construction hair dryer is best, but a high-power household hair dryer is also suitable);
• solvent (White spirit);
• stationery knife or thin fishing line;
• rags;
• rubber scraper;
• about an hour of free time.

How to peel off side window deflectors: step-by-step instructions

Open and securely lock the door from which you will remove the visor. Clean the work surface, wash and dry if necessary.

Turn on the hairdryer and thoroughly but gently heat the area where the deflector is fixed to the door. Be careful as excessive heat may damage the coating.

Pry up one of the edges of the windshield and thread the fishing line under it.

Continuing to heat the visor with a hairdryer, move the line to the opposite edge, cutting off the plastic from the tape and paintwork. Take your time. If there is no fishing line at hand, then the manipulation can be carried out using a stationery knife, but even more carefully and slowly.

Once the visor is completely removed from the door, you will need to remove the industrial tape that was used to affix it. To do this, take a rag, soak it generously in solvent and, soaking the tape, remove it with a scraper.

After completely cleaning the door from traces of fastening, wash and dry its surface.

If you are not sure that you can remove the windshield from your truck yourself, trust the specialists at the service station. They will carry out the dismantling procedure carefully, without damaging the paintwork of the side door.

Removing plug-in windshields

How to remove the side window deflectors, if they were installed under a rubber seal, using a clip or mechanical method. Let's say right away that this will take much less time than peeling off the visor. You just need to unscrew the screws that secured the windshield for reliability (if any), and then pull out the rubber seal. Remove the visor, check that there are no traces of corrosion underneath, and return the rubber band to its place.

In the Autolong online store you will find a wide selection of windshields for trucks, which can be mounted with adhesive tape or by insertion.

You may also be interested in the following articles:

• Which company to choose window deflectors
• Removing deflectors: how to remove wind deflectors correctly
• Rain protection on car doors and windows
• Why are window deflectors needed?
• Truck side window deflectors
• How to put deflectors on a truck window?
• What is a windshield or deflector for a car?
• Why do we need wind deflectors and car window deflectors?
• Where to buy door deflectors?
• How to order wind deflectors and window deflectors?
• How to install deflectors on side windows?
• Choosing deflectors for the car brand

Removing deflectors from windows: how not to break the lining

Side window deflectors are a part of the car door necessary to protect the body and people inside the car from rain and strong winds from outside the car when driving with the window partially open.

In appearance, the side window deflectors are a part made of polymer or chrome-plated metal. The main properties of window deflectors include protection from wind, small debris, raindrops and increased comfort for smoking drivers and passengers.

What are window deflectors

Instructions for removing side window deflectors

Removing the side window deflectors is quite simple; you will need the following set of tools:

• Strong thin wire. Fishing line is ideal.
• Construction hairdryer.
• Galoshes, solvent, alcohol, white spirit. One of these chemical compounds.
• Scraper for removing frost from glass. Sold in any auto store for 100 rubles.
• Rags. An old, preferably clean, rag.

Preparing the surface and car for installation

To work successfully, you should stock up on:

To prepare the surface you need to:

— The car is first washed, and the mounting points are thoroughly wiped with a solvent.

— Special attention should be paid to cleaning if the body was polished using mastics that contained wax/paraffin.

— It is recommended to install deflectors on an adhesive base in the absence of humidity and at a temperature not lower than +15°C.

How to safely remove old adhesive from baffles

The procedure for removing the adhesive layer or remaining adhesive tape is required when replacing the cutters.

We offer several cleaning methods that have been tested in practice:

All methods require care and patience to avoid damaging the surface during operation.