Hyundai Getz fuses: where they are and how to remove them, causes of malfunction and troubleshooting, step-by-step instructions for replacing them yourself


Fuse and relay box in the engine compartment

In the Hyundai Getz it is located between the left fender, the starter battery and the air filter housing.


The fuse diagram and its explanation are given below.


Fuse diagram under the hood. Scheme printed on the lid


Fuses and fuses

Number in photoDenomination, AProtected circuit
810Air conditioner
910Sound signal
1015Engine ECU; Injectors; Sensors: -camshaft position; - crankshaft position. Idle air control; Canister purge solenoid valve
1150Electric power steering
1510.15Reserve
1640ABS ECU;
1720Air bleed connector
1820Generator
1910Air conditioner; Fuel pump; Immobilizer antenna unit; Oxygen concentration sensor; Fuel pump; Air conditioner
2010Fuel pump; ECU
2110ABS ECU; Air bleed connector
2250Tail lights; Fuses No. 11, 19, 20, 25, 27, 29 of the cabin unit
2420Automatic fuel cut-off switch
2630Egnition lock; Starter
2730Egnition lock

Relay

Number in photoServiced chain
1Interior heater fan
2Turning on the engine cooling fan at high speed
3Turning on the engine cooling fan at low speed
4Starter
5Air conditioner
6Sound signal
7Fuel pump
12Power windows
13Interior heater fan
14Security alarm
23Radiator cooling fan
25Fuel pump; Generator; ECU
30Electronic Engine Control Power Supply

Where is the starter located on the Hyundai Getz?

1spare fuses
2security alarm relay E47
3fuel pump relay E49
4horn relay E45
5air conditioning relay E50
6starter relay E41
7relay for turning on the engine cooling fan at low speed E43
8relay for turning on the engine cooling fan at high speed E44
9interior heater fan relay E51
10power relay for electronic engine management system E42
11connector E55

Block in the cabin

It is hidden behind a plastic cover in the upper left corner of the storage compartment on the driver's side of the instrument panel. There are fuses on the front side of the block and relays on the back side.

On the back of the cover there is a paper diagram of the location of the fuses in the Hyundai Getz. Photos and transcript are given in the table below.

Circuit breakers

DesignationRated current, AProtected consumer circuits
110Air conditioner switch
210Parking light lamps on the left side of the car
310Airbag
410Audio system; Electric exterior mirrors
510Automatic gear selector switch; Reversing light switch
610Parking light lamps on the right side of the vehicle; License plate lamps; Door ajar alarm
710Instrument cluster indicator lamps; Seat belt warning timer; Security alarm control unit
820Cigarette lighter
910ECU; Generator; Electric power steering ECU; ABS wheel speed sensors; Overdrive lock switch
1010Airbags
1120Door lock system
1215Tailgate wiper motor
1310Starter; Security alarm
14Reserve (not used)
15Reserve (not used)
1620Front seat heating switch
1710ECU; Switch for heated rear door glass and exterior mirrors (optional)
1815Ignition coils; ECU
1915Brake light switch
2015Hazard switch; Security alarm
2120Windshield wiper and washer motors
2210Rear fog lights
2310Fog lights, Power windows; Timer for heating the trunk door glass; Electric drive of left and right headlights; Headlight range control switch
2410Heater fan
2530Heated rear door glass
2615Right headlight bulb
2710Fog lights
2815Left headlight bulb
2915Rear fog light switch; Door open warning lamp sensor; Audio system; Diagnostic connector; Interior and trunk lighting
3130,20,15,10Spare fuses

Additional designation: 30 - plastic tweezers.

Relay

DesignationPowered consumers
K10Turn signals and hazard warning lights
K11Fog lights
K12Switch for heated rear door glass and exterior mirrors (optional)
K13Side light bulbs
K14Electric windows
K15Fog lamp
K16Not used

We disassemble the cigarette lighter in Getz: how to remove, repair

The device is found in every modern car. Now even non-smoking drivers use it. And not only for its intended purpose - for lighting cigarettes, but as a connector for a 12-volt outlet. Electrical devices are connected to the device’s socket: from a mobile phone charger to a compressor, inflating tires or a vacuum cleaner.

Therefore, failure of the cigarette lighter has a negative impact on driver comfort. Below is information on how to remove the device on Hyundai Getz and Accent models, repair it or replace it.

The device and how the cigarette lighter works

The device consists of several main parts - a connection socket where several wires come and a metal rod that is inserted into the connector. The Hyundai Getz cigarette lighter comes with three cables.

  1. Constant positive (red cable). Connected to the battery via a standard fuse. Responsible for heating the metal coil located inside the cigarette lighter.
  2. Positive backlight cable. The device is equipped with a filter ring that illuminates the hole. A positive wire of yellow or white color is suitable for it.
  3. Minus. Powered to the device body. The second end fits into the car body, this is the mass. Has black insulation.

A special nichrome wire is mounted inside the cigarette lighter itself. After pressing the button, the contacts close, and current begins to flow through the device, causing the wire to heat up. After 15-20 seconds, the maximum temperature is reached, and then the Hyundai Getz thermostat gives the command to turn off the heating and snap the cigarette lighter to its original position.

Causes and troubleshooting

In order to remove the cigarette lighter on a Hyundai Accent or Getz model, you will have to dismantle the front console. Before repairing, you should find out the cause of the malfunction; perhaps everything can be solved in a simpler way.

  1. Blown cigarette lighter fuse. Due to the connection of powerful devices, the current strength of this section of the circuit may exceed the permissible value of 15 amperes. To protect the wiring from melting, the fuse fails. You need to get to the Hyundai Getz mounting block and replace the element with a working one.
  2. Short circuit. If the elements burn frequently or the cigarette lighter fuse is intact, then there is a high risk of a short circuit. In this case, you will need a tester or voltmeter. It is necessary to check the battery voltage with the ignition off and then on. If there is a drop of more than 0.5 volts, then you need to look for a short circuit. All cables should be tested for resistance.
  3. Broken cigarette lighter wiring. Age can cause cable soldering to come loose. The wiring should be inspected for kinks, abrasions, or unnatural bends. When localizing the break point, solder the cable or replace it with a new cord of suitable cross-section. The recommended wire diameter is at least 1.5 square meters. mm.
  4. Poor contact. Due to frequent use or connecting foreign devices, the cigarette lighter socket on the Hyundai Getz may become loose, as a result, not providing reliable fixation. In this case, it is recommended to bend the fixing tendrils using a flat screwdriver.
  5. The appearance of oxides or rust. Refers to “age-related” problems. It is necessary to periodically remove the Hyundai Getz cigarette lighter and inspect the contact points for the appearance of oxides or rust. If present, remove them with a file to ensure optimal conductivity.
  6. Spiral deformation. After repeated heating, the metal thread may burn out. Here it is recommended to remove the cigarette lighter of a Hyundai Accent or Getz car and replace it with a working device.
  7. Failure of the backlight lamp. There is a special light filter around the socket that makes it easier to find the connector in the dark. The light bulb may burn out over time. This requires dismantling the filter and replacing the part.

Removal and replacement process

To replace fuses and relays on a Hyundai Getz, you will need the following tools:

  • plastic tweezers,
  • 10 mm socket head,
  • 10 mm wrench,
  • crosshead screwdriver.

Before carrying out work, you must remove the key from the ignition switch.

Under the hood

The procedure is as follows:

  1. Open the hood.
  2. Open the unit cover by pressing the plastic latch on the windshield side.
  3. Pull out the blown fuse with tweezers and the faulty relay with your hand. If you need to replace fuse link No. 18 (protects the generator), then unscrew the fixing bolt with a key and a 10mm socket.
  4. Check the vehicle's electrical wiring and eliminate the cause of the blown fuse.
  5. Install new protective elements.
  6. Install the removed parts in reverse order.

In the cabin

The procedure is as follows:

  1. Remove the mounting block cover by grasping the notch in it with your fingers.
  2. To replace fuses: Use tweezers.
  3. Find and remove the burnt out element.
  4. Install new one.
  • To replace the relay:
      Remove the lower instrument panel trim by removing 2 screws from the lower left and right corners of the panel.
  • Unscrew the 2 bolts securing the unit to the instrument panel with a 10mm head and pull it towards you.
  • Turn the block over.
  • Pull out the required relay and insert a new one.
  • Make sure that the unit or its circuit is working properly after replacing the element.
  • Reinstall the removed parts.
  • Fuse box Hyundai Getz, Elantra, Sonata

    On the roads of Russia and the post-Soviet countries, encountering a Hyundai car is, frankly speaking, not uncommon, which is not surprising in principle, because Hyundai Motors is the largest automaker in Korea and the fourth largest in terms of this indicator in the world market.

    The company's engineers set themselves a single task: to make a car that will appeal to, if not everyone, then many car enthusiasts from all over the world.

    It is impossible to achieve this without multi-functional electrical equipment of the models, as a result of which there are a huge number of electrical devices in any Hyundai.

    A breakdown of one or another electrical circuit unit can occur for any car owner, even despite the high quality of Korean units. Often the culprit is a faulty fuse box. That is why our resource decided to cover in more detail the topic of repairing this unit in Hyundai cars using the example of generally recognized models - Getz, Elantra and Sonata.

    Description of fuses

    Remove the unit cover. Disconnect the wiring harness block from the mounting block. Unscrew the two bolts securing the mounting block to the body panels, press out the clamps of the protective casing of the wiring harnesses and disconnect it from the mounting block. Remove the relay from the mounting block.

    Using a screwdriver, press out the wire holder clamps and remove the holder. Using a similar method, remove the remaining wire holders in the mounting block. Use a screwdriver to press the wire terminal retainer and remove the wire from the mounting block body.

    Location of fuses, fuses, relays and their replacement Hyundai Solaris

    Auto News

    Dealers have collected almost 10,000 pre-orders for the Genesis GV80

    The GV80 premiered in January 2021. Serial production of the new product is planned for the summer of this year. Genesis CEO made a prediction that consumer demand for their first crossover could exceed supply. 14 May 2020 11:05:51 +0000

    Sales of the new Gazelle have started in Russia

    Sales of the new Gazelle NN City model have started in Russia. The first commercial vehicles have already begun to arrive at GAZ dealerships throughout the country. A dealer from Stavropol was one of the first to post photos of the new product on his page on the social network Instagram.

    14 May 2021 10:24:35 +0000

    Sales of new cars in Russia collapsed by 72% in April

    Sales of new passenger cars and light commercial vehicles (LCVs) in Russia fell in April 2021 by 72.4% year-on-year (after an increase of 4% in March and a decrease of 2.2% in February) to 38,922 thousand units, calculated in the Automobile Manufacturers Committee of the Association of European Businesses (AEB).

    12 May 2021 09:53:00 +0000

    Rostelecom provided Avtodoria with

    Rostelecom provided - to a domestic developer and integrator of intelligent transport systems in the field of road safety.

    14 May 2021 08:34:31 +0000

    Sales of the Chinese GAC minivan will start in Russia this summer

    The Chinese company GAC, which came to Russia in December with the only GS8 crossover, may expand its line with the GN8 minivan and GS5 SUV this summer. This was reported by the Chinese Cars portal with reference to the official representative of the brand.

    13 May 2021 13:20:00 +0000

    BYD will present an electric car cooler than Tesla for Europe

    At the beginning of this year, BYD introduced its flagship crossover Han. The electric model, according to the developers, will become a more budget-friendly alternative to the American Tesla, but will surpass it in equipment.

    13 May 2021 13:59:51 +0000

    In Russia, the electric crossover Jaguar I-Pace has dropped sharply in price

    Jaguar has announced a reduction in retail prices for the I-Pace electric car. The model has fallen sharply in price due to the zeroing of the import duty on vehicles with electric powertrains to the countries of the Eurasian Economic Union.

    13 May 2021 12:41:50 +0000

    Aurus civilian sedan spotted in Europe

    The Aurus Senat luxury sedan was spotted on European roads. Most likely, the owner of the car with Belgian license plates is a private customer. Judging by the photographs, the European Senat has no external differences from the Russian version.

    14 May 2021 06:13:54 +0000

    The cost of a self-assembled Lada Vesta from spare parts has been announced

    Autoblogger Andrey Makar found out which is cheaper: purchasing a new LADA Vesta from a dealer or assembling a car using spare parts. An experiment with calculation of the cost of all 180 basic parts and a conclusion about whether it is possible to save money on buying a LADA car in this way was published on his YouTube channel.

    13 May 2021 12:10:00 +0000

    GAZ began sales of new variations of “Sadko Next”

    GAZ Group began sales of a new generation of off-road trucks “Sadko Next” with an extended wheelbase and a double cab. The body of such cars can accommodate up to seven passengers, including the driver, and provides the possibility of transforming the rear row of seats into a full-fledged berth.

    13 May 2021 12:55:00 +0000

    1.16. Circuit breakers

    GENERAL INFORMATION

    Your vehicle's electrical system is protected by fuses.

    1. Fuse panel cover

    If any lights, accessories, or controls do not operate, inspect the fuse for the appropriate circuit. If it is burned out, its melted thread will be visible.

    If the same fuse blows again, avoid using this system and contact your authorized dealer as soon as possible.

    1. Fuse puller*

    Standard fuse

    1. Normal

    2. Burnt out

    Replacing fuses

    1. Turn off the ignition and other electrical circuits.

    2. Open the fuse panel.

    3. Remove the fuse using the puller located on the fuse panel.

    4. Inspect the fuse and, if it is blown, replace it with a new one.

    5. Insert a new fuse with the same rating and make sure it fits securely into place. If this does not work, please contact your authorized dealer to perform this operation.

    If you don't have spare fuses on hand, borrow a fuse

    from a circuit that is not critical to the operation of the vehicle,

    for example, from a radio system.

    Warning

    Always replace the fuse with a new one of the same rating. Otherwise, the electrical system may be damaged.

    1. Fuse box cover

    The protrusion is indicated by an arrow.

    If the lights or other electrical components do not work and all fuses in the cabin are intact, inspect the fuse box under the hood.

    Follow these procedures:

    1. Turn off the ignition and other electrical circuits.

    2. To remove the fuse box cover, remove it from the latch and pull it up from the protrusion side.

    3. If the fuse is blown, replace it with a new one of the same rating.

    Main fuse

    1. Normal

    2. Burnt out

    Replacing a 100 A fuse

    1. 100 A fuse

    1. Check that the ignition is turned off.

    2. Disconnect the negative battery terminal.

    3. Unscrew nuts A.

    4. Lift the switch block and unscrew bolts B.

    5. Replace the fuse with a new one of the same rating.

    6. Follow the procedures in reverse order to return the vehicle to operating condition.

    Fuse box (engine compartment)

    Fuse panel

    Fuse box (engine compartment)

    DescriptionAColorProtected component
    1AD FAN30 ApinkAdditional cooling fan for air conditioner*
    2INJ30 ApinkFuel injection system
    3MAIN100 AblueTo protect all electrical systems
    4COOLING FAN30 ApinkCooling Fan
    5HEATER40 AgreenHeater air conditioner*
    6IG KEY40 AgreenFuses 2, 3, 4, 7, 10, 13, 14, 15 and 16 on the fuse panel
    7BTN40 AgreenFuses 6, 8, 9 and 11 on the fuse panel
    8ABS*60 AyellowAnti-lock braking system*
    9TAIL15 AblueTail lights
    10HAZARD15 AblueEmergency light signaling. Direction indicators
    11STOP15 AblueBrake lights
    12FOG15 AblueFront fog lights
    14HEAD LOW15 AblueHeadlights (low beam)
    15HEAD HI15 AblueHeadlights (high beam)
    Rating
    ( 1 rating, average 5 out of 5 )
    Did you like the article? Share with friends:
    For any suggestions regarding the site: [email protected]
    Для любых предложений по сайту: [email protected]