How to remove the front and rear door trim on a Priora - instructions for disassembling and reupholstering with photos and videos

How to remove the door trim on a Priora: front, rear - step-by-step instructions

Removing the car door trim is a mandatory procedure if you need to carry out certain operations - repairing wiring, installing new equipment such as speakers or window lifts.
Cars from the Lada Priora line have a standard door mechanism design, which allows you to open it by following the same instructions regardless of the model. The vehicle owner only needs patience, a set of tools and strict adherence to instructions to avoid damage to the trim. The design of the rear and front doors on cars is slightly different, but the general principle of operation is the same.

Tools for removing car trim

The standard list of tools includes:

It is advisable to have a special kit for removing the trim; if you don’t have them, you can use a flat-head screwdriver or something similar;
Set of tools for removing trim and clips
Phillips screwdriver;
TORX key (T20);
spare pistons/clips for fastening.

It should be taken into account that the clips may crack when removed, so it is better to stock up on additional copies just in case. It is preferable to buy the kit in advance to save time at work

It is worth paying attention to what model the clips are purchased for - only for the Priora, the rest do not match in size

Clips for door trim of different Lada models

If electronic elements are installed in the doors, you will need a wrench - this applies to window lifts.

It is necessary to have space to open the doors to the sides, so you need to empty the garage/box of unnecessary things that interfere with the procedure.

Another option is to take the car outside in warm weather, and collect all the removed elements in a tool box with pre-prepared compartments, so that nothing gets overlooked during reassembly.

It is imperative to disconnect the battery if there are electronic components in the doors, so as not to provoke a short circuit and the need for premature replacement of wiring and other spare parts - just remove the negative wire

When using screwdrivers, the best option would be to wrap them in electrical tape so as not to scratch anything (including the paint on the metal), and you need to work with the tools carefully - without sudden movements

Dismantling begins by unscrewing the screws located near the door handle. Next you will need to remove the screws holding the power window control module

At this stage, care must be taken not to damage the glass itself. The window lifter element will need to be removed along with the module for controlling the mirrors

Next you need to work in the following sequence:

if there is a speaker in the door, then it is necessary to dismantle it;
unscrew three screws from the bottom of the casing;
the screw at the door handle is unscrewed;
Next you will need a TORX wrench; use it to unscrew two bolts in the recess on the armrest;
The pad on the armrest itself, in addition to the bolts, is attached to latches - you may need a flat-head screwdriver to unlatch them. Be careful! The latches are quite fragile and can break if pressed hard.
the wires are connected to the removed cover with a special plug; it is simply removed;
the door lock is twisted;
Now the trim is held in place only by clips around the perimeter of the door.
Removal is recommended to be done using special trim removers so as not to break the clips. You can operate from any of the angles - the casing is pryed up and carefully, but with little effort, removed from the clips. Location of clips on the Priora door

How to remove the rear door trim on a Priora

For the rear doors, the sequence of actions is approximately the same, and even easier, but it is worth considering the design features and location:

use a Phillips screwdriver to unscrew the bolt from the recess for the door handle;
Two bolts are also unscrewed in the recess of the armrest. If necessary, the entire pad is removed from the clips and removed;
the cap from the door lock is twisted off;
Three bolts are unscrewed from the bottom of the casing;
Using a special puller or a flat screwdriver, the trim is carefully removed from the clips. It is done!
Read also: Rules for self-recovery of gel batteries at home

Assembling the door will require the same steps, but in reverse order.

Dismantling begins by unscrewing the screws located near the door handle. Next, you will need to remove the screws holding the power window control module. At this stage, care must be taken not to damage the glass itself. The window lifter element will need to be removed along with the module for controlling the mirrors. Next you need to work in the following sequence:

if there is a speaker in the door, then it is necessary to dismantle it;
unscrew three screws from the bottom of the casing;

the wires are connected to the removed cover with a special plug; it is simply removed;

Location of clips on the Priora door

Useful and visual videos of removing the front door trim from a Priora:

Reassembling the door after carrying out the necessary operations is carried out in the reverse order. You just need to make sure that all electrical and mechanical components are connected correctly. Contacting a workshop will not be a rational decision if you study the instructions in detail and do everything exactly as described and shown in the pictures. The first time the process will take a little longer, but later working on the car will become much easier.

Stages of removing the casing

Before removing the trim from the clips, you must remove all bolts, clamps and fasteners that are located in different parts of the door. It is most convenient to do this in a certain order.

Before you begin removing the door trim, disconnect the negative cable from the battery.

From the front door

To remove the door trim on a Lada Priora, you need to get rid of all the fasteners. To do this, follow the following procedure.

Unscrew the button responsible for locking the door and remove it. Unscrew the screw on the inside door handle. Remove the handle by carefully moving it away with a flat-head screwdriver. Find the two screws in the special pocket that secure the power window control module. They can be hidden under a rubber mat. Unscrew both screws and remove the ESP module. Now you need to disconnect the connector with wires from it. Locate the three screws at the bottom of the door that secure the trim to the door. Turn them inside out. This way you got rid of all the screws and fasteners. Now you need to take a flat-head screwdriver and carefully pry off the casing at the bottom. Unsnap all eight clips, which are indicated in the diagram, starting from the bottom of the door

Be careful at this stage: broken fasteners are quite difficult to repair. Carefully remove the trim. If done correctly, you should encounter almost no resistance.

Location of the main screws that prevent the removal of the casing

Due to their small size, screws and clips are often lost. To make the reassembly process easier for yourself, before starting work, prepare a container where you will put all the small parts.

To install the trim in place, place it against the door. Make sure the fasteners are in place. Insert and tighten the lock button. Thanks to this, you can pre-fasten the door components. Make sure the handle fits into its hole. Now you can snap all the clips into place and screw the screws back in.

Video: how to properly remove the trim from a Lada Priora car with your own hands

From the back door

The procedure for removing the trim from the rear door of a Lada Priora is not much different from what was given in the instructions for the front door. The exception is when working with window lifters: here they have a slightly different mechanism.

Unscrew the door lock button and remove it.
Using the same screwdriver, carefully press out the window lifter handle lock.
Pull out the handle itself and its lock.
Remove the screw holding the inner door handle trim.
Remove the trim using a flathead screwdriver.
Remove the two screws located in the small pen pocket under the rubber mat, and then remove the pen.
Starting at the bottom of the door, remove the trim from the clips. The operating principle is the same as for the front door.

The rear door is assembled in the reverse order.

Be careful when working with wiring, especially those for window regulators. It is quite thin, so it can tear easily.

As you can see, the process of dismantling both the front and rear door trim of the Lada Priora is not particularly complicated and does not require many tools. A set of two screwdrivers will be sufficient. To avoid damaging the door, follow the main rule: not only unscrew the screws, but also remove the parts attached by them. All additional elements, such as door handles or window lifters, will greatly interfere with the process of removing the trim. If you strictly follow all the instructions, you can easily disassemble and reassemble the door trim without resorting to the help of specialists from car services.

Removing Priora door trims

We decided to do the sound insulation ourselves or simply repair something inside the door (ESD, door handle, etc.), then we will need to remove the door trim .

LADA Kalina door trims are secured using bolts and special plastic holders (clips). There is a possibility that the clips will break when removing the upholstery (especially in the cold season), so it is recommended to buy new clips in advance.

To remove the door trim you will need a straight and Phillips screwdriver. Before starting work, disconnect the negative cable from the battery.

Removing the front door trim of the Lada Granta

To carry out work to replace or repair car parts, sometimes you have to disassemble the front and rear doors of the car, which is not so easy to do. Lada Granta car owners also have to face such difficulties, but by following the simple instructions described below, you can easily do all the work yourself.

Why do you need to remove the door trim?

This procedure is relevant if you need to carry out repair and restoration work on the doors of a Lada Granta car. For example, it could be:

sheathing repair. If the plastic is cracked or broken in some places, the door cards will need to be repaired after removing the trim. It will be possible to solder a metal mesh into the inner part of the casing. This way the damage will not spread, and the cracks can be sealed with a primer and covered with paint. Another way is to reupholster the doors with new material; New interior trim for Lada Granta

noise and vibration insulation. In order to improve the acoustics in the cabin and make the doors close quieter, it is necessary to eliminate squeaks and rattles. To do this, after removing the skin and disassembling the structure, you should glue a special material, for example, “Vibroplast”

It is important not to forget to seal all technical holes with vibration material. Then all the elements should be assembled and installed in place; Installing soundproofing on a car door. door reupholstery

door reupholstery

If you need to update the sheathing material, you should first remove it and disassemble the entire structure. The front doors are more difficult to cover because there are more bends and holes. Therefore, all calculations must be made correctly. Glue the material from the center and stretch it to the edges using an industrial hair dryer. You need to make cuts in the right places. When the surface is processed, all structural elements can be installed in place; Interior trim

airbrushing in the interior. Recently, it has been important to improve the appearance of not only the external surface of the car, but also the interior. To do this, for example, they do airbrushing on fabric on the door trim or ceiling of a car. The material must be painted black or dark blue. Then, using an airbrush device, you need to apply stripes in the form of lightning. After the paint has dried and the trim has been installed in place, you will see amazing effects in your Lada Granta car. You can choose any motif and color scheme.

Instructions for removing the trim on a car door

So, in order to remove the trim from the front doors of a Lada Granta car, you must sequentially perform the following steps:

Take screwdrivers and prepare new clips.
Disconnect the negative terminal of the battery.
Remove the door lock button.
Door lock button
Using a flat-head screwdriver, pry out the fastening screw plug.
Then remove the screw using a Phillips screwdriver.
Unscrew all screws securing the door trim.
Location of the casing fastening screws
You need to remove the material from below, from the corner. To do this, insert a screwdriver between the metal and the casing.
Continuing to remove the coating, you should move in both directions from the corner.
If there are any devices installed in the doors, they must be turned off and then the covering must be removed completely.
After this, you can begin the work you intend to do.
Installing the trim in a Lada Granta car is done in the reverse order.

So, if you have a desire to improve the quality of your Lada Granta car, you can always bring any ideas to life on your own. All you need is time, tools and suitable materials.

Removing door trim on Grant

It is necessary to remove the front or rear door trims on a Lada Granta car in various cases, which can be listed below.

Failure of the motor or the window lift mechanism itself
Replacement of side door glass
Sealing the internal door cavities to improve sound insulation
Repair or replacement of locks, cylinders or opening handles

The replacement process is quite simple, so you can do it all yourself without any problems. At most, this will take no more than 10 minutes.

So, before starting the repair, you need to open the car door and use a thin screwdriver to pry off the plug, under which there is a screw securing the trim. Clearly shown in the photo below.

Then unscrew the screw securing the inner door pocket, which is also the handle.

After this, it is worth unscrewing two more screws that are located at the bottom of the Granta upholstery - which secure the so-called pocket.

We unscrew the screw securing the door opening handle and then remove the protective rubber cover in the area of the rear view mirror control handle. This is clearly shown by the yellow arrow.

After this, you can carefully pry it from the bottom of the upholstery and with sharp, but at the same time careful jerks, pull it off the latches.

It will not be possible to completely remove it right away, since the power wires to the window regulator unit will interfere, which must be disconnected.

Also, if you have front speakers connected and they are installed on the trim, which is often the case, the wires from them must also be disconnected.

After which you can finally remove the door trim on the Grant and carry out the necessary work further, for which all this was even necessary! Installation of the casing occurs in the reverse order and will not be particularly difficult.

Removing and installing rear door trim on Lada Granta cars

As for the rear door, its trim is not much different in terms of fastenings from the front door. But still, there are some different points that should be mentioned.

The presence of a full door closing handle means that there are two more screws that will additionally secure the trim. They are located under decorative plugs.
There is no power window control unit, so there is no need to disconnect extra wires when removing.

Replacement or installation is carried out in the reverse order of removal. The price of new skins in case of damage and the need for replacement ranges from 4,000 to 6,000 rubles for a complete set.

Removing Priora door trims

We decided to do the sound insulation ourselves or simply repair something inside the door (ESD, door handle, etc.), then we will need to remove the door trim .

To remove the door trim you will need a straight and Phillips screwdriver. Before starting work, disconnect the negative cable from the battery.

How to remove the door trim of a Lada Priora yourself

The car brand was released twelve years ago, and since then has been very popular among drivers. And it’s not surprising, because the cost of a high-quality product from the domestic automobile industry is quite low. Many car enthusiasts can afford to buy it. Repairs and service are cheap, and some parts can be replaced yourself. For example, from this article, readers will learn how to remove the Priora door trim.

The assembly quality of the parts is at a high level, even able to compete with the assembly of some foreign cars, so components will have to be repaired or replaced only after the time specified in the technical instructions for the car. The huge advantage of the Priora is that the engine does not “eat” huge amounts of fuel, which allows you to save money.

In some cases, vehicle owners want to replace the door trim on the Priora. Achieving this goal is quite simple; you will need a minimum of tools. Lack of experience should not be scary; even people who are not involved in such repairs will be able to remove the old door trim and install a new door trim according to the instructions.

How to remove the trim

The process is divided into three main stages:

Finding all screws and fixing elements, unscrewing the bolts.
Removing door trims.
Dismantling the casing.

The covering of the rear and front panels is removed separately. These steps will be described in detail below in the article; if you do not want to go to a car repair shop, we will provide instructions on how to remove the door trim on a Lada Priora car.

Why is dismantling necessary?

The upholstery of the Lada Priora car is available in several colors. If a car enthusiast wants to change the interior color, then he will have to change not only the seat upholstery, but also the door trim. Components such as noise insulation or insulation cannot be installed without first removing the sheathing.

If the window lifts are damaged, or the door handles are damaged, you will also have to remove the Priora door trim, notice the broken components, and install it back. Also, over time, the cladding loses its appearance, stains appear that cannot be removed.

How to dismantle the casing: instructions

The front and rear door trim can be removed separately:

You will need the following tools:

flat screwdriver;
Phillips screwdriver;
clips and pistons to which the covering is attached.

It is not necessary to complete the last point, but it’s better to stock up on clips and pistons in case you break the old ones. In order not to waste time and not run to the store, it is advisable to buy the kit in advance.

When choosing caps or clips for Priora, pay attention to what brand they are intended for. These components for Priora are similar to parts for Kalina

The difference is in length - for Kalina, the clips are one and a half millimeters longer. Ask consultants for help, they will help you choose the right parts.

Front door

So how do you remove the front door trim? Reading the instructions:

Unscrew the door lock latch.
Unscrew the screw securing the handle to the door. Remove the screw and remove the handle.
Unscrew both bolts that hold the switch block. Remove the unit; to do this, unclip the wires from the connector.
Find the three fixing screws at the bottom of the door, unscrew them, and set them aside.
Unclip the trim clips using a flathead screwdriver. Using the flat tip of a screwdriver, pry up the edges of the casing and carry out the process from the bottom up.

Such simple manipulations allow you to remove the front door trim. Install the new or old covering (depending on the purpose) in the reverse order

Backdoor

How do you remove the rear door trim? See instructions:

Remove the socket from the glass receiver handle.
Move the fasteners aside.
Carefully remove the window handle and set it aside.
You will find three bolts at the bottom of the door, unscrew them.
There are four latches on top; unscrew them with a Phillips screwdriver.
On the side, where the handle is located, there is another bolt, unscrew it.
There are two screws on the other side of the door, unscrew them.
Take a flat-head screwdriver and pry up the trim from below, gradually separating it from the door. Perform manipulations from the bottom up.

Install the door trim in reverse order. A map of the location of the fasteners can be found on the Internet, so you will be sure that you are unscrewing the bolts that secure the covering.

Conclusion

The dismantling process will not take much time and effort. It is so simple that the decision to go to a workshop and order a replacement of the covering there seems irrational. Following the instructions, everyone will be able to remove the Priora's trim.

Features and possible complications

It must be remembered that plastic is very easy to scratch. That is why it is recommended to wrap a slotted screwdriver with electrical tape. But, most importantly, all actions should be performed very carefully. This guarantees the integrity of the skin.

Plastic caps are prone to breaking. Even with the most careful dismantling, you will break at least one of them. Therefore, it is advisable to have a couple in stock. As a last resort, you can visit the store before assembling the door. When purchasing, please note that you need pistons for the Priora. They are externally difficult to distinguish from the same parts for Kalina. But, at the same time, it is 1.5 mm longer. This difference may prevent you from properly securing the sheathing.

There are various electrical appliances in the doors. Therefore, when dismantling, be sure to pay attention to the wiring. This is especially important for window regulators. The wiring here is very thin and easy to pull out, and this happens almost “from the roots.” Restoring the wiring is quite difficult. Also, when assembling, pay attention to the location of the wires. Pinched wiring can cause locks or mirror drives to fail. It is better to immediately position them as they should be, so that later you do not have to disassemble the door again.

Conclusion

. Domestic cars are very easy to repair. All design elements are quite simple. Therefore, the question of how to remove the rear and front door trim on a Priora is practically no problem. It is important to follow the order of disassembly, which will speed up and facilitate the process. Also be careful when disconnecting wiring.

Step-by-step instructions for removing the front door trim

In fact, it's not that difficult to do. First, let's figure out what tools are needed to remove the trim. Before work, prepare the necessary materials.

For work we will need:

straight metal screwdriver;
metal Phillips screwdriver;
clips for fixation;
thick tape for insulation.

Let's start dismantling the front door trim of the Lada Priora. The actions are performed in the following order:

You must unscrew and remove absolutely all the screws located around the door handle. Carefully unscrew them using a Phillips screwdriver. Now slowly remove the bolts securing the window lift control module to the door. Inspect it and find the fastenings that need to be removed.
Next, you will remove this module and the mirror adjustment system of your car. Take them off. Set the parts aside.
Having disconnected the clamp located inside, remove all the wires that are connected to the systems and lead to power supplies. Make sure that no current is flowing through them, otherwise you may get injured.
Now start unfastening the trim fasteners near the handle. Unscrew all the bolts one by one. Use the screwdriver you feel most comfortable using.
After this, carefully peel off the trim. Set it aside.
The facing part of the door is fixed with screws. To remove it, just unfasten them. Then get rid of the button blocking the lock. Take it out.
Now slowly lift the trim using a screwdriver and remove all the plastic fasteners. Then set them aside.
That's it, job done.

Step-by-step instructions for removing the rear door trim

Roughly speaking, the principle of operation is absolutely the same as with the front door. The only significant difference is that the rear door does not have a lift-lowering mechanism.

Using a flat-head screwdriver, you should unfasten and push aside the mounting handle that raises the window of your car.
Unfasten the handle mechanism and its lock from the shaft using a screwdriver.
Remove the screw that secures the door handle trim, located inside the trim, and move it to the side.
Use a flathead screwdriver to pry up the trim and remove it.
Ready!

Summarize

Removing the trim is not as difficult as you think

Please note that you will need several different screwdrivers to get the job done, as well as some insulating tape and clips. It’s better to prepare your tools in advance

The procedure is the same in both cases. It is enough to remove all the fasteners and carefully remove the casing. This procedure is mandatory before repairing parts and mechanisms located inside the door. Thus, you can easily access the parts protected by it.

Basic operating rules:

Work carefully, try not to damage the parts.
Don't lose any fasteners or parts you've removed.
Ensure your own safety when working.

Front door

We proceed directly to removing the casing. Before this, it is advisable to prepare a slotted screwdriver; its tip is wrapped with electrical tape. This avoids damage to the plastic. Using a screwdriver, carefully press out the plastic pistons;
After this, the casing is shifted upward and removed from the window glass groove. Also, don't forget to disconnect the wires going to the window regulator. As a result, the cladding is completely removed.

Next, all planned actions are carried out, and everything is put back together. When installing an anti-cricket gasket, it is very important to accurately mark the holes for the pistons. If there are additional holes, the effectiveness of such modification will decrease.

Front door diagram. Catalog numbers of parts

Soundproofing front doors on Lada Granta

The pasting process is not complicated.

We prepare:

2 sheets of Visalis AL, dimensions 460x700 mm or more in reserve;
1 sheet of Bitoplast, size 1000x700 mm;
half a meter of corrugation for wiring the front door;
degreaser;
hair dryer or any other heating device;
gloves;
tools, screwdrivers;
rags.

Algorithm of actions

After installing the structure (the process is described above), degrease the surface, clean it of dirt and corrosion.
At the same time, we evaluate the condition of the vibration-isolating gasket and cover it with a new one.
Cut Visalis into the required sizes.
We lubricate all driving mechanisms and hinges.
We isolate all possible sound sources.
We cover the surface of the upholstery with vibration-absorbing material.
We heat the Bitoplast and press it against the metal surface of the door.

If the algorithm is followed, the doors will close silently, as if in a foreign car.

The process of dismantling the structure is described above; we follow its points. After installation by screwing it onto the hinges, we proceed to assembly and filling the inside. Instead of worn rubber seals, we install new ones. This completes the self-replacement process.

The sequence of dismantling the door trim

First of all, carefully remove the decorative trim that covers the mirror adjustment. We dismantle it using the same clip cutter or a flat screwdriver (but very carefully).
Remove trim from door handle. Also, using a clip on the side of the lock, pry up the lining and remove it. Remove by hand to avoid cracks.
Remove the screw from the door handle.
Next, place the clip on the side under the handle and bring it to the middle of the width of the handle. The panel should pop out without much effort. The panel, as a rule, has a special spike in the center that can easily be broken. To remove it carefully, you need to slightly lift the panel and at the same time slightly pull the trim towards you with a clip puller.
Now the wires are visible. They must be disconnected from the power window controls.
At this stage there are 3 screws left at the bottom of the door. We unscrew them. Usually on all cars there are 3 screws at the bottom of the door.
The casing is now held in place only by internal clips. We grab the casing from below and carefully pull it towards us. The clips should come loose and clicks will be heard.
After the pistons have fired, we lift the casing up and release it. Clips can become fragile over the years, so it is advisable to install new ones.

How to remove and replace the rear door on a Priora

If there is a need to remove the rear door on a Priora, then this is also not difficult to do.

It is important to take into account the following features of dismantling work:

In order to remove the product after unscrewing the fasteners, you must first disconnect the rubber cover from the door. It should be disconnected at the junction with the door, and not the body part (depending on which side you plan to pull the wire from).
Next you need to remove the door card. You can read how to do this.
If there is no need to dismantle the door card, then you should disconnect the power supply to the power window console and lock. It is located near the seat belt mechanism (B-pillar) under a plastic decorative trim.
There is no need to completely remove the cover. To do this, unscrew the fastening element, as shown in the photo.
And move the cover aside.
Disconnect the chip with the wire from the power window control console (if equipped) and insert it through the hole.
Similarly, disconnect the chip from the electric lock drive, and also insert the wire through the hole.
After this, unscrew the opening limiter mounting bolts using an 8/10 socket, depending on the modification.
Using a "13" key, unscrew the two bolts securing the hinges.
Have an assistant hold the door while unscrewing the bolts.

Installation of a new door is carried out in the reverse order of removal. This completes the expert description of the process of removing the rear door on a Priora, and with the help of these instructions you can implement the procedure yourself without the need to contact a car service center.

If there is a need to replace products on a Priora, then you should know that products from the VAZ-2110 are suitable for this car. They are completely identical except for some points, as you can learn from the video material below.

In addition to everything, it is important to note that if you install a door from a VAZ-2110 on a Priora, then you can save about half on the cost of the product. The replacement process does not take much time, and even a beginner can cope with its implementation

How to remove door trim

The door trims on the Lada Priora car are attached in the same places as on the tenth family, but the removal procedure will still be different. So, they generally have to be removed for various reasons:

to replace the casing itself due to damage, etc.
for replacing door cylinders, locks or glass
installation of acoustics (front speakers)
when soundproofing doors

If for any of these reasons you need to remove the front door card, then below is a list of the necessary tools:

Torx bit t20
Bit holder and adapter
Phillips screwdriver

The procedure for removing and installing casings on Priora

First of all, you need to open the car door, and then unscrew the three screws securing the trim from the bottom. This is clearly shown in the photo.

After this, again using a Phillips screwdriver, unscrew the screw from the recess of the door opening handle.

Now we unscrew the locking cap itself by hand, as shown in the photo below.

Now, using a T20 Torx bit, unscrew two screws in the recess of the door handle.

Having pryed this pocket open and freed it from the latches along the edges, we take it out. It is assembled with a control unit for power windows and mirrors. In order to remove it, you need to disconnect the block with the power wires. There is nothing complicated about this.

Next, we slightly pry up the corner of the skin, trying to carefully free it from the clips on at least one side.

Next, we slowly move up and, as if in a circle, we try to “tear” the casing from the fastenings.

When you have already released it from all sides, you can carefully disengage the opening handle and remove the upholstery completely, as is clearly shown.

I think that it is possible to show the result that is obtained in the end.

Now you can carry out all the necessary actions, for the sake of which this part was dismantled in the first place. After completing the necessary work, you can perform the installation in the reverse order.

If the clips securing the upholstery to the door were damaged during removal, the broken ones must be replaced with new ones. The cost of a set of plastic parts for the entire Priora car is no more than 250 rubles.

I think that to make the presented material more accessible, you can show a video review prepared specifically for this article.

priora-remont.ru