How to replace the ignition key of a Kia Rio
To change the battery in your Rio key, you don't need any tools other than perhaps a small flathead screwdriver, although you can do without it.
The first step is to press the metal button on the key fob to bring its blade into an extended state. Then, in order to open the Kia Rio key, you need to slide its back part as shown in the photo. Once the plastic cover is removed, the battery is accessible and can be removed with your fingers. To make it more convenient to remove it from its seat, you can use a small flat-head screwdriver here. You must try not to damage the metal contacts and microcircuit with its blade.
We put the new battery in place with the “+” sign up, and the “-” sign down towards the circuit board. After that, put the plastic cover back in place. You need to make sure that it is pressed tightly against the key fob body along each edge.
In order to check the functionality of the ignition key, you need to press the “Lock” and “Open” buttons several times. If the battery is installed correctly, the vehicle will respond by flashing the turn signals and opening or locking the doors.
Battery, Ignition key
More about Rio cars:
Important addition
But it also happens that there is nothing to replace the battery with, but you have to go. An LED light on the key fob that does not respond to key presses indicates that the old battery is completely discharged. In this case, we do not get upset, but act as follows. We approach the car, release the mechanical key from the device and carefully open the driver’s door. At this time, the switched on standard alarm is triggered. After it stops, you can start starting the engine. But this is not so easy to do: the “start-stop” button does not work, and the smart key is not detected by the on-board computer. But all is not lost, because... Korean engineers have come up with a clever system specifically for such cases. We lift the armrest between the driver and passenger seats, and a niche opens in front of us, at the bottom of which a secret is hidden in the form of a recess for a smart key. With the bottom side we insert it there until it stops and fix it.
After this we try to start the car again. This time everything should work out: the system will react and come to life, and the engine will start working. Now you have a chance to safely get to the place where you can buy a new battery. First, we remove the smart key from the slot into which we previously inserted it. While the central locking is not working, you can lock and unlock the interior with a mechanical key.
This surefire method has more than once rescued car owners in seemingly hopeless situations. It is good because its implementation does not require a lot of time and effort, and you also do not need to enter any codes, passwords, ciphers, otherwise this would greatly complicate the task, although it would increase the level of vehicle security.
This example teaches us how a harmless organizational nuance (if neglected) can develop into a rather serious technological problem. Therefore, always have a spare battery in the glove compartment (or better yet, more than one), just in case.
Flip key - what is it?
For the first time I had to deal with a flip ignition key when buying a new car (well, not new, unfortunately, but quite fresh). There was a so-called “test drive”.
Sitting in the passenger seat, the owner of the Mercedes handed me a black box. At my bewildered look, he smiled: “Pull the string and the door will open!” I pressed the button and - oh, miracle! — the tip of the key jumped out of the box! I immediately remembered the switchblade. which I was terribly proud of as a child. Well, I can’t say that these keys were the main reason for buying this particular car, but they were not the last place on the list of options I liked!
Switchblade key? It's stylish!
The fashion for car accessories is varied and unpredictable, as is the fashion for other signs of confirming a person’s status. She did not ignore this small and seemingly insignificant part of the car’s interior. Car keys have gone through an evolutionary path from a simple metal blank to a stylish sparkling electronic “haute couture” masterpiece.
Disassembling a flip key on a Hyundai
How to open a car if the battery is dead
There is a situation when the car alarm does not turn on and there is no reaction to a working key fob. This often happens if the battery is dead. Especially when it is not new or when the machine has been idle for a long time. In this case, in order to unlock the vehicle, you will need to supply power to the battery or starter.
If the battery is located in the rear of the car, you will not have to open the hood. It is enough to connect the red terminal for lighting to the upper positive part of the retractable generator, where a wide wire comes from, and fasten the black “crocodile” to the ground of the car. The main thing here is not to confuse the polarity, so as not to get the control unit repaired.
Opening an old Hyundai/KIA key
We open the key carefully, first of all we take care of our fingers. We use a knife to go around in a circle, then we pry the shell with something and the inner part with the blade easily comes out. The shell is flexible, as if slightly rubberized, so it does not break, but simply bends almost without losing its shape, you can push it apart with your fingers if you cut it well.
Flip key for Hyundai/KIA
In general, it was easy to find and buy a Hyundai/KIA flip key. We bought it on Aliexpress for 191 rubles with delivery. The quality of the key is at a high level, which is surprising. Someone says that the quality is even better than the original, let’s not argue, they didn’t hold the original in their hands, but you can believe it. Local sellers had the same keys for 1200 rubles, the same Chinese ones. Specifically for our 2012 KIA Rio III, a key blade with the Solaris inscription was suitable. And those with the KIA inscription had the wrong blades. The photo shows what we are talking about.
Everything else is simple. We get the key and go to the “key holder”. Prices for cutting blades are different, if we decide to save money, then we’ll go around and look for an acceptable one. As a result, the prices were 650 rubles, 500 rubles. and in one place where the cost was 500 rubles, they cut it for us for 300 rubles, perhaps they just realized that in front of them was a real good person).
Emergency opening
While using the car, a situation arises when the car has slammed the alarm and the key
stayed inside. How to open a Kia Rio without keys? There are several methods:
- Break the glass, open the door from the inside. To do this, choose the cheapest car glass.
- It is worth bringing with you an inflatable ball or a flat rubber bulb with a pump. Having tucked the deflated ball into the gap between the door and the opening, pump it up with air as hard as possible. With all this, the door will move away. Insert a thick wire bent with a hook into the created gap, hook it to the handle, and pull. The door will open.
- Using a bank plastic card and a piece of rope 1.5 meters long. The card is inserted from above into the doorway between the seals, partially of its own length. A loop is tied in the center of a narrow, strong rope. These are functional devices that will be used throughout the entire life of the car. The main and repair keys are included with the car. Additionally, a special key fob is issued, which indicates the number of certain keys, and in addition a hidden hidden code for a set of anti-theft accounting programs.
Only on the basis of these numbers are duplicates ordered at Toyota Motors service stations.
KIA Spectra 2008, 101 l. With. - funny
Doors on Rio 1 - 17, thousand. Doors on Rio 3, , , , - thousand.
Solaris doors go for about the same price. A new body part from the assembly line and a part from disassembly, of course, also differ in price.
How to open a car without a key - in 1 minute. Solaris
You can buy cheaper at a disassembly, but at the same time you are not insured against defects that may be present on the product you are purchasing and which you may not immediately notice.
How to open the doors of a Kia Rio without a key?
It happens that a situation occurs when the car doors are closed, the keys are left inside, and the spare set is lost. The most obvious and common solution in this case is to break the window.
But replacing glass is not cheap, so you don’t want to resort to such a drastic solution. So is there an alternative and is it possible to open the door on a Kia Rio without a key?
With the Marijuana Celebration Day quickly approaching, many in Winnipeg are asking what will happen to those who choose to partake in smoking marijuana right out open at a festival. That has led to a conflict of rules stemming from the city and the province in relation to the event.
Provincial officials believe that the protest should be converted to a celebration.
According to Winnipeg marijuana lawyer Marijuana is going to be legalized in Winnipeg in the summer of this year. Many marijuana advocates see as a way to introduce marijuana to the public and celebrate the fact that it has finally been legalized.
The situation is banal, my wife is in the store, buying more of what they forgot, I’m sitting in the car, waiting for Friday evening, before going to the dacha.
It turns out my beloved and I went out to open the trunk while lightly slamming the door. And-and-and oppa, neither the trunk nor the doors open.
I was looking for a thin stick, but somehow I couldn’t find thin ones that bent, thicker ones, I had to force the door, I tried the method of bending the top of the driver’s door. There was dancing with a tambourine for about an hour, the situation was heating up, everyone was nervous.
People of non-Slavic appearance came up, asked what had happened, explained the situation, they also suggested using a stick or wire, but if the trees grow, it was of no use, and they couldn’t find the wire.
In the same way, you can open any of the doors or the hood, for example, if you need to charge the battery. The envelope can be replaced with a screwdriver wrapped in electrical tape, the main thing is not to damage the seal, then the same mechanism for hooking the door latch with a curved wire is activated.
It is important that in the process of opening the doors in this way, the alarm installed on the car will go off, so you must be prepared to explain your actions.
The ease of opening the door should prevent the driver from forgetfulness. Keys left in the car can easily make your car a target for thieves. How to start a Kia Rio without a key Is it possible to start a car without having a key with you?
Knowing how to open a Kia Rio and get into the interior, you can use two standard options to start the car. The most difficult thing will be to remove the steering wheel, take out the lock and go to a specialized workshop where they will make a new key.
How to disassemble a Kia key
In this article I will tell you how to disassemble the Kia Cerato key. The key was accidentally washed, after which the locking and unlocking buttons on the remote control stopped working. In addition, the battery began to run out very quickly, CR2032 in 3 days. The key itself does not have a collapsible design, it is glued together. Having received carte blanche from the owner, he got down to business. The chip in this key is not on the board, it is located separately and it functioned properly. Pressing any button lit up the key's LED, the key emitted certain frequencies, but only the trunk release button worked.
How to disassemble a KIA Cerato flip key
I started disassembling the key from the side where the blade is placed when folded. We heat a thin screwdriver and carefully, slowly move it. I did the same thing at the bottom of the key (with the battery cover removed). These places are hidden during operation, so I started working from them. The task was to remove the board and preserve the appearance of the case, since there was no replacement.
Step-by-step replacement process
Replacing the Kia Rio flip key battery
- First of all, meet the “culprit” of our conversation today. You will need its analogue.
- It is necessary to throw out the “sting”.
- Rotate the body into a comfortable position and pull the plug upward with great force with your fingers. Do not be afraid, since the lid is installed very tightly, and you need to use force to open it.
- OK it's all over Now. All that remains is to replace the battery and put the cover back in place.
Replacing the Kia Rio Premium key battery
This type of key fob is slightly different from its predecessor, therefore, the process is also slightly different.
- To begin, disconnect the “tip” from the body by pressing a special button and remove it.
- Now, using an object with a thin blade or edge (a knife, a flat-head screwdriver, even a coin), pry the side slot from all sides so that a visible gap appears.
- All that remains is to separate the halves of the case, replace the key battery and reassemble it in the reverse order.
Don’t be lazy and timely replace the battery every 1.5-2 years, depending on the manufacturer and operating conditions, and you will never experience difficulties with the operation of the Kia central locking system.
How to open a Kia Rio without a key: how to change the battery and disassemble the key
Minor key repairs - replacing KIA buttons
Then I picked up a 2mm bolt from some old radio equipment, there are little ones like that in the board mount and took a couple of twins. The main Kia key to disassemble fits all the car locks without exception: This is how I began to mock my key, by inserting two sushi chopsticks.
How to completely disassemble a flip key without breaking it Kia and Hyundai Flip Key HOW TO…
It is necessary to open the plastic cover of the key fob with a fingernail, knife or thin screwdriver. There is not a single video or photo report on this topic. Such sets of keys are supplied at the factory with special devices with electronic memory.
Good luck to everyone and I look forward to your comments or questions and will help in any way I can.
Here is the inner world of one half.
Half Here is the inner world of the other half. The view from the outside - halves with buttons, I was glad that I didn’t click. A button and a spring from the switch mechanism of the key itself.
Quite small things, you can become an Agronomist - you almost sowed, be on your guard when extracting! This is a board with micro buttons on one side, and this is the same board on the other side.
How to open a Kia Rio without keys? Break the glass, open the door from the inside.
For this purpose, choose the cheapest car glass. It is worth having an inflatable ball or a flat rubber bulb with a pump. Having tucked the deflated ball into the gap between the door and the opening, inflate it with air as much as possible.
Key fob, how to take it apart?
The door will then open. Insert a thick wire bent with a hook into the created gap, hook it to the handle, and pull.
Using a bank plastic card and a piece of rope 1.5 meters long. The card is inserted from above into the doorway between the seals up to half its length.
Third method: use a flexible wire.
This method has been repeatedly tested in practice. All you need is a wire about two meters long and some kind of wedge. We will need to push the wire inside the cabin. To do this, you will need to slightly press the upper corner of the driver's door, the one that is closer to the pillar. This can be done using a wooden wedge or an old plastic card. You can also use a screwdriver, knife, stick and other improvised items.
So, we move the door and the seal and begin pushing the wire inside with movements back and forth. We brought it inside and lowered it to the level of the bottom edge of the glass. Now we need to pull the right end of the wire to pull it out to such an extent that we can tie a loop on it. We knit a noose-type loop - which tightens if you pull the ends. If anyone doesn’t know, first we make one loop, next to another. We insert one loop into the second, insert a finger into the inserted loop and tighten. It turns out to be a noose - a noose. Now you need to carefully, so that it does not tighten prematurely, push it into the interior again. We put the loop on the clip that is located on the door. We'll have to try. Now we tighten the loop. All that remains is to pull it up. To prevent the loop from flying off the clip and not having to re-tie it and put it on the latch, leave one end of the rope, the one in your right hand, in place, and gradually move the other end, the one in your left hand, to a vertical position to the level when it is right above the clip. Now that the wires are at right angles, all you have to do is pull them at the same time, the latch should rise up.
You can do the same steps with a thin rope or fishing line.
How to disassemble a KIA, HYUNDAI flip key with your own hands, photo, buy new buttons | "Legnum INFO"
By drilling holes in the key blade and the turning mechanism.
For this, I used a 2.3mm drill. I finished all the edges with a needle file.
Then I picked up a 2mm bolt from some old radio equipment, there are little ones like that in the board mount and took a couple of twins. The first is for cutting threads in the fist, the second is for finishing fastening the tip.
The bolt should fit freely into the tip. Next, I degreased all the fastened parts and applied cold welding Poxypol and immediately tightened them with a bolt.
The bolt was previously sharpened inside the fist so that it would not cling and the excess glue was removed from the inside.
Sometimes it expires earlier, which is why the central locking begins to respond worse to pressing buttons, and after a while the car stops opening and closing. To prevent this from happening at the wrong time, the battery must be changed in a timely manner.
How to disassemble a KIA flip key
In Kia flip keys, the most common type of battery is CR 3V. They can be found from different companies such as: When purchasing an element, it is better to pay attention to its expiration date in order to exclude a situation where it stops working after a couple of months. How to replace a Kia Rio ignition key In order to replace the battery in a Rio key, you do not need any tools other than perhaps a small flathead screwdriver, although you can do without it.
Recommended Posts
If there is still a reinforcing bar left, unscrew it too. We reach for the lock cover, press the latches, and remove it.
How to open a Kia Rio without a key
We pull it down, the trunk lock is open. This method has been repeatedly tested in practice. We will need to push the wire inside the cabin. How to open the trunk of a Kia Rio without a key Sometimes a situation arises when you urgently need to open the trunk, but you don’t have the key with you or the trunk lock does not work.
Sometimes it will be enough to open the driver or passenger door, get into the cabin and open the trunk from the inside. The second option would be to use a screwdriver using wooden wedges and wire.
In this case, the alarm will notify everyone around you about illegal entry. How to open a Kia Rio key fob Often, car doors do not open because the battery in the key fob has stopped working, while the central locking does not work, the car does not open or start. A signal about the need to change the battery will be a reduction in the distance at which the key fob is activated.
Create an account or sign in to comment
When replacing, a CR tablet type battery is installed at 3V. The shift itself will require no more than 5 minutes of time.
Replacing the battery in the Kia Sportage key fob
That is why, if your KIA chip key is working at the software level, but is broken at the physical level, we will help you fix it for minimal expenses. Namely, to repair a KIA of this level, we suggest replacing the car key body.
That is, we will machine a tip for the car’s ignition switch, and then we will replace the chip from your original broken key into the key blank. Car keys Repairing a chip key of this level at the Hephaestus car service does not take much time.
Kia Sportage Club. Kia sportage ignition key
We will replace the key body with an identical one, ideally machine a tip for the keyhole of the car's ignition system, and then we will assemble everything correctly and fully check it.
We have many blank keys in stock. These are classic-looking car keys, flip keys, as well as fish chip keys, smart keys and others.
The only thing is, if you want to order a replacement case for how to disassemble the key of a cue sportage ignition key, then call in advance and check the availability of a blank key. Phone number for inquiries and orders at the Hephaestus car service: Programming chip keys Moreover, dear KIA owners. In our car service center, you can order physical repair of a chip key if the case has fallen apart, the tip of the key has broken, or the button on the flip key is stuck, as well as software repair of chip keys.
That is, if the car key chip appears to be working fine, but it no longer opens the door locks at the press of a button and does not start the car, then it is damaged at the software level.
A number of car repair shops will tell you to buy a new key or even a new immobilizer, but we can repair your existing car electronics and help you save money on this car repair. Hephaestus car service offers the most complete chip key repair, immobilizer repair and car electronic control units.
Topic: Central lock + key fob
Central locking + key fob
Such a disaster happened.
Today I just took the key fob and stopped working - the car wouldn’t lock or unlock from it. Only with the key.
I started to blame the battery (because I saw the red light blinking on the key fob), tried to disassemble the key fob (according to the manual), but this turned out to be an impossible task and upon returning home I decided to change the key fobs and park the car. But it turned out that the second key fob did not work either. and then I suspected something was wrong, I locked the car with the KEY and found that ALL the doors, except the driver's, were OPEN. This means the lock did not work, nor did the key fob.
But, having sat inside, I checked the operation of the central locking button and it worked, properly closing the doors. Realizing that I didn’t understand anything, I decided to remove the terminal and give the BC a rest. After reconnecting, nothing changed.
Since I didn’t want to sleep in an open car, I closed the car, deceiving the system. I taped the door switch with tape and slammed the door by pressing the central locking button.
Well, it’s understandable to go to PN to OD, but suddenly someone has encountered this. Any advice?
How to open a Kia Rio without a key: how to change the battery and disassemble the key
Minor key repairs - replacing KIA buttons
Then I picked up a 2mm bolt from some old radio equipment, there are little ones like that in the board mount and took a couple of twins. The main Kia key to disassemble fits all the car locks without exception: This is how I began to mock my key, by inserting two sushi chopsticks.
How to completely disassemble a flip key without breaking it Kia and Hyundai Flip Key HOW TO…
It is necessary to open the plastic cover of the key fob with a fingernail, knife or thin screwdriver. There is not a single video or photo report on this topic. Such sets of keys are supplied at the factory with special devices with electronic memory.
Good luck to everyone and I look forward to your comments or questions and will help in any way I can.
Here is the inner world of one half.
Half Here is the inner world of the other half. The view from the outside - halves with buttons, I was glad that I didn’t click. A button and a spring from the switch mechanism of the key itself.
Quite small things, you can become an Agronomist - you almost sowed, be on your guard when extracting! This is a board with micro buttons on one side, and this is the same board on the other side.
How to open a Kia Rio without keys? Break the glass, open the door from the inside.
For this purpose, choose the cheapest car glass. It is worth having an inflatable ball or a flat rubber bulb with a pump. Having tucked the deflated ball into the gap between the door and the opening, inflate it with air as much as possible.
Key fob, how to take it apart?
The door will then open. Insert a thick wire bent with a hook into the created gap, hook it to the handle, and pull.
Using a bank plastic card and a piece of rope 1.5 meters long. The card is inserted from above into the doorway between the seals up to half its length.
