Torpedo for pulling and setting nets under ice
At all times, there have been fishing enthusiasts who don’t care about heat or frost. They catch fish with a spoon in the summer with a fishing rod, and in the winter they will not refuse to set nets. And if earlier they had to make holes and pull a cord through them using a long stick, today a torpedo has come to the aid of fishermen for pulling nets under the ice. This convenient and compact device has captivated many winter fishing enthusiasts.
Appearance of the device
The material for making a fishing torpedo is metal or plastic. The device is made in the form of a cylinder with a cone attached to the front. It has a hole on the top that is responsible for draining water that gets into the device. At the back of the torpedo there is a lever, thanks to which the device is turned on and off. made of non-freezing material is attached to it . Two lights are attached to the top of the torpedo, allowing you to see the device even through a meter of ice.
Inside the under-ice networking torpedo there is a motor that runs on eight large batteries. On the sides of the device there are wheels with a jagged edge. It is thanks to them that the torpedo moves.
The device has the following external data:
Due to the fact that the device is quite light and compact, it is convenient to take it with you on winter fishing. Which the fishermen support in every possible way.
Replacing the instrument panel with a new one
As we previously recalled, in addition to the suggested methods, there is also the most expensive, but also the highest quality option, which is a complete replacement of the instrument panel.
Nowadays, instrument panels that are based on a large display instead of analog instruments are in fashion. Even on domestic cars you can install such a miracle and the panel will take on a modern look. When choosing, it is worth remembering all the parameters of your car, since even different engines can play a role in the choice. Such a panel allows you to completely customize the devices to your taste, their location, lighting and other parameters. In a word, do everything to the driver’s taste. Below we have provided a video example of the operation of such an instrument panel on a VAZ 2114 car.
This technology is based on a large display covering the entire instrument panel, a minicomputer based on Android and a set of devices, Wi-Fi, Bluetooth.
Such a replacement is usually short-lived, but expensive, so first you should think about whether you need it or just for beauty.
Method of using the device
In order to use the torpedo to install nets under the ice, you need to unscrew the back cover of the device. Then place large batteries into the opened cavity. After which you need to check that the device is ready for operation, which can be easily done by lightly pulling the rope:
After making sure that the torpedo is in working order, you can go out onto the ice. Directly on the spot, the fisherman cuts a hole into which the device will be lowered. Then a cord is tied to the twine, with the help of which the net will be stretched. The torpedo is lowered under the ice, into a hole, and directed in the desired direction. A slight tug on the rope sets it in motion. Due to the fact that the device rubs against the ice with its wheels, the fisherman hears this grinding sound and also sees a glowing light bulb.
After the device floats as long as necessary, the cord is lightly tugged again and the engine is turned off. Having retreated a little from this place, the fisherman cuts a second hole, removes the apparatus from the water and secures the cord. All that remains is to stretch the network along it and install it in the right place.
Some fishermen will improve the device with their own hands in every possible way. For example, you can attach a metal clamp in the area of the wheels, touching it will make more noise. This can be useful if the ice becomes thicker and the light from the bulb is not visible. Others make homemade bright lamps by soldering additional LEDs into them, after which the resulting cavity is filled with autosealant, and the plus LED is fixed to the central contact.
There are also craftsmen who attach a piece of foam plastic to the bottom of the torpedo. This is done so that the device fits more tightly to the ice. In general, each fisherman modifies the device in his own way, making the device even more convenient and efficient.
Film instead of LEDs
A simpler way is to use film instead of LEDs or LED strip. The advantage of this method is its simplicity and lower costs. Getting started is the same as in the previous case. It is worth unscrewing and removing the instrument panel, then disassembling it to the base where the backlight is located. Now the procedure begins to differ. Typically, the factory backlight is white (in domestic cars), and the color changes thanks to the film on the back of the devices.
The more transparent the film, the brighter the instrument illumination will be; depending on the color of the film, the instrument illumination will be. The principle is designed in such a way that light from a standard backlight passes through the film, thereby changing color and illuminating the devices.
Here, as they say, the colors will be limited by your imagination; you can make numbers of one color, arrows of another, and lines of a third. Some amateurs use sandpaper and a scratch pad to clean the base of the instruments on the back side (from the backlight side) so that the numbers and indicators appear brighter. The film can be used as a special film, also sold in car dealerships, or you can find it yourself from scrap materials. A big plus is that no changes will be made to the electronics, which means there can be no short circuit.
DIY making
Some specialists can make a torpedo tackle themselves. To do this, make a wooden float about 15 cm long and weighing about 100 g . A lead plate is attached to the bottom, the weight of which should lower the product to a depth of 10 cm. A leash is made from a monofilament line with a diameter of 0.2 mm. It is tied to the main line, but just below the float. A fly 30 cm long and 0.2 mm in diameter must be attached to the leash. Then the side floats are fixed (length 9 cm, width 0.2 mm) at a distance of 30 cm from each other.
This device also quite effectively helps fishermen in their work. But, of course, to make it, you need to have certain skills and abilities.
Fragmented noise reduction option
When it is not possible to completely disassemble the dashboard, there is only one option left - to do it partially. The result of the procedure, of course, will not be as impressive as with major work, but it will still be noticeable. In this situation, it is necessary to remove the maximum possible elements that are subject to vibration, and therefore the formation of “noisy” play. You need to work with them as was suggested in stages 1 and 3 when completely dismantling the dashboard.
Everything that is written above also applies to the lining of the central tunnel. Often this is an element consisting of 2 parts, or a one-piece structure, which also needs to be processed using the presented technology.
Many motorists are concerned about the answer to the question of why the engine stalls after starting, and what to do about it. We know how to deal with this problem
If you liked it, please share with your friends!
Assembly kit
The torpedo, produced by the Air Toy brand, is a small kit for self-assembling a floating craft.
The main part of the elements, such as the body, “tail” and elements of the control system, are made of plastic using high pressure molding.
That is, these are quite accurate and high-quality parts. Judging by the photos and reviews - without unnecessary flash and technology flaws.
The propeller, assembled from 3 parts, is made of soft rubber-like plastic and requires not only assembly, but also separation from the sprue.
Like in bench modeling. However, this model is for real swimming.
Putting a sticker on the dashboard
In addition to the above mentioned methods for changing the color of the backlight, you can also change the appearance, that is, the image of the instruments as the driver will see them.
For this purpose, special stickers are most often used. To do this, you should disassemble the instrument panel and get to the instrument backing, on which the values and numbers are printed.
It is worth remembering that stickers are sold for each model, make and year of manufacture of the car separately. As an example, it may be the same car, make and model, even year of manufacture, but the instrument panel is different. One will have a tachometer, the other will not. Therefore, stickers should be selected very carefully.
Before gluing, try it superficially on the factory panel to see if it fits the fasteners, or if there is anything that interferes with the smooth application of the sticker. If the old coating can be removed, then it is better to do so; the new sticker will look much prettier. Now that everything is fine, the surface on which you will glue it should be wiped with a degreaser. Glue one side and, while pressing the sticker, slowly pull off the protective layer. It’s important to smooth it out so that there is no air under the sticker, otherwise the temperature will cause it to peel away from the surface in a few months.
After completing the procedures, you can put everything back together and mounted it to see how well the instrument panel has improved. Next, we assemble everything in reverse order, installing the panel in its proper place.
How to save a model from water?
Therefore, the kit includes a set of gaskets. They are necessary when assembling a housing from several elements. Otherwise, sealing will fail and the motor will be flooded with water.
Since the torpedo is powered by a conventional electric motor and a pair of batteries, the result will be disastrous.
Ideally, all joints will need to be sealed with sealant or moisture-resistant glue. But after the complete assembly of the unit.
Unfortunately, access to the engine compartment and the batteries located in it is only possible when disassembling the device.
Therefore, it is not worth gluing the torpedo tightly, and it is better to use standard waterproofing products.
The set also includes a nice-looking stand. It will come in handy - after applying the inscriptions, it turns out to be a very nice interior decoration.
Which can be removed from the base at any time and sent on a real voyage.
How to make proper soundproofing of the dashboard with your own hands
The main source of all squeaks in a car is the dashboard, and it doesn’t matter whether it’s a foreign car or a domestic car. In general, there are several reasons why the silence in the cabin can be disturbed.
The primary reason lies in the integrity of the entire structure. The dashboard is a whole set of plastic elements that are connected to each other using various fasteners - screws, clips, etc. Over time, constant vibration in the car makes itself felt - these fasteners become loose, weaken, and sometimes even fall off. All this results in the appearance of backlash and squeaks.
Another reason for the appearance of such a nuisance is the abundance of numerous elements hidden under the dashboard. This includes various electrical, heating elements, numerous wiring harnesses, etc. All of them are not fastened in place, which causes them to “knock” on the dashboard.
It would be wrong not to mention the third reason, which also exists - the low quality of the plastic from which the dashboard is made.
You can not only get rid of such noise, but also use the dashboard as an auxiliary barrier in noise reduction. Something like an acoustic shield that can significantly reduce the audibility of the engine in the cabin.
Torpedo for winter fishing - description and operating instructions
Every year the number of people who want to fish on their own does not decrease. Even in the age of high technological development, there are still citizens who sometimes want to be alone with nature. Today, a huge list of various devices for fishermen has been invented. This text will focus on a torpedo.
With this interesting device you can place ordinary fishing nets directly under the ice. Moreover, this can be done at any depth and it will take no more than half an hour. In the cold season, when reservoirs are covered with ice, such a device will be simply indispensable for people who catch fish for sale in large quantities.
Characteristics of a torpedo for fishing
Size and weight
The length is 55 cm, and its diameter is approximately 9 cm. The weight is only 1 kg. Such characteristics allow the device to float perfectly under ice and perform its functions. In addition, such lightness and comparative compactness will allow the fisherman not to experience inconvenience when carrying.
User manual
Advantages of using a torpedo
There are several positive aspects to using such a device:
The cost of such a magical device may depend on the material from which it is made. An important role is played by the engine power and its brand. Thus, the price can range from 1500 to 2000 rubles.
A fishing torpedo is a fairly common device and can be purchased at many fishing stores.
You can also easily order it online, select the material from which it will be made and the power of the electric motor, and order spare gears.
How to catch more fish?
Making torpedo tackle at home is quite simple. You don’t need any special skills other than the ability to handle a fishing net, as well as attentiveness and strict adherence to technology.
Materials
Manufacturing process
Reviews about using a torpedo for fishing
The torpedo is quite common and there will be no problems with the search. The price is basically affordable. Light weight and acceptable dimensions make it one of the most convenient fishing tools to use.
Now only mine bites!
I caught this carp using a bite activator. Now I never return home without fish! The time has come for you to guarantee your catch. The best bite activator of the year! Made in Italy.
Now only mine bites!
I caught this carp using a bite activator. Now I never return home without fish! The time has come for you to guarantee your catch. The best bite activator of the year! Made in Italy.
Full Noise Canceling Option
In this material we will not talk about how to dismantle the dashboard - the instructions supplied with the car, as well as special formulas, will help in this matter.
Let's just say three key points:
• Take your time and be very careful. • To avoid losing the fastener, screw it in immediately. • Label electrical terminals.
So, the panel has been removed, now it should be disassembled into parts so that only the cast elements remain intact. Wipe them thoroughly to remove dust and dirt.
Fishing with a popper, glider, torpedo: tactics, technique, video
Today there are a lot of different artificial baits for spinning rods. These are different types of spinners, wobblers and other baits. Today we will talk about such an interesting product as a popper. A popper is a surface bait that uses the sounds and splashes it makes to attract a variety of predators. The popper is great for catching: pike, chub, pike perch, pike perch, asp and many other predators. Therefore, popper fishing is very popular.
What are surface baits?
Already by the name you can tell that these baits work on the surface.
If many other spinning baits are visually inaccessible for control, then these analogues can be seen on the surface. Why use poppers? Everything is very simple! Suffice it to remember the warm summer days, when a predator fights on the surface in various places. It’s not so easy to catch fish with ordinary spinners and wobblers. it is on the surface. It is for these cases that surface analogues are used. It is advisable to use surface analogues from early summer until late autumn. If we talk about the southern regions, then it can be used from the end of spring. Be sure to take poppers if you are going to fish in overgrown reservoirs or swamp-type reservoirs where using conventional spoons is problematic. Try to use them in calm conditions, when there are no waves on the water, otherwise the predator will not see the game.
Rod and line
A lightweight and at the same time rigid carbon fiber rod is the best option for a popper.
Build – fast or ultra-fast. A rigid spinning rod is necessary for accurate casting, since when fishing in places with a lot of grass, you need to be able to hit the “windows”. Regarding the length, it depends on the fishing conditions. For fishing from the shore, purchase models with a significant length; from a boat, you can use short analogues. Generally speaking, short spinning rods for such baits are preferable (2-2.4 meters). The short rod allows you to use different retrieves. When using long rods, purchase models with small dough (about 20 grams). A certain margin of safety for the spinning rod is necessary, since you will often have to wade through water thickets.
Thus, for popper fishing, use a short, light and durable spinning rod.
Regarding fishing line, you can use braided or monofilament analogue. The stiffer the spinning rod, the more elastic the fishing line should be, and vice versa. Each angler knows that monofilament flies further than braided line. To increase the casting distance of the braid, it can be impregnated with silicone.
Accession
To attach the bait to the fishing line, you can use a miniature fastener, which is sold in any fishing store. This is suitable for fishing without leads as there is a clasp on the leads. When catching a toothy predator, it is necessary to use steel leashes. It turns out that when fishing for asp, chub, perch, use special fasteners to attach the popper to the main line. When catching toothy predators, it is enough to use a leash.
Torpedoes and poppers
In fishing stores you can find a huge assortment of surface baits.
Popper is the main and most popular bait for fishing on the surface of the water. For perch, I recommend using Rapala bait. Such a bait makes high-quality plopping sounds during a short retrieve, thereby attracting fish. Choose a popper based on the principle: the less effort it takes to get a popping sound, the better. Torpedoes are less popular than the above analogue. This is a cylindrical bait with a propeller.
Torpedo for pulling and setting nets under ice
At all times, there have been fishing enthusiasts who don’t care about heat or frost. They catch fish with a spoon in the summer with a fishing rod, and in the winter they will not refuse to set nets. And if earlier they had to make holes and pull a cord through them using a long stick, today a torpedo has come to the aid of fishermen for pulling nets under the ice. This convenient and compact device has captivated many winter fishing enthusiasts.
Appearance of the device
The material for making a fishing torpedo is metal or plastic. The device is made in the form of a cylinder with a cone attached to the front. It has a hole on the top that is responsible for draining water that gets into the device. At the back of the torpedo there is a lever, thanks to which the device is turned on and off. made of non-freezing material is attached to it . Two lights are attached to the top of the torpedo, allowing you to see the device even through a meter of ice.
Inside the under-ice networking torpedo there is a motor that runs on eight large batteries. On the sides of the device there are wheels with a jagged edge. It is thanks to them that the torpedo moves.
The device has the following external data:
Due to the fact that the device is quite light and compact, it is convenient to take it with you on winter fishing. Which the fishermen support in every possible way.
Method of using the device
In order to use the torpedo to install nets under the ice, you need to unscrew the back cover of the device. Then place large batteries into the opened cavity. After which you need to check that the device is ready for operation, which can be easily done by lightly pulling the rope:
After making sure that the torpedo is in working order, you can go out onto the ice. Directly on the spot, the fisherman cuts a hole into which the device will be lowered. Then a cord is tied to the twine, with the help of which the net will be stretched. The torpedo is lowered under the ice, into a hole, and directed in the desired direction. A slight tug on the rope sets it in motion. Due to the fact that the device rubs against the ice with its wheels, the fisherman hears this grinding sound and also sees a glowing light bulb.
After the device floats as long as necessary, the cord is lightly tugged again and the engine is turned off. Having retreated a little from this place, the fisherman cuts a second hole, removes the apparatus from the water and secures the cord. All that remains is to stretch the network along it and install it in the right place.
Some fishermen will improve the device with their own hands in every possible way. For example, you can attach a metal clamp in the area of the wheels, touching it will make more noise. This can be useful if the ice becomes thicker and the light from the bulb is not visible. Others make homemade bright lamps by soldering additional LEDs into them, after which the resulting cavity is filled with autosealant, and the plus LED is fixed to the central contact.
There are also craftsmen who attach a piece of foam plastic to the bottom of the torpedo. This is done so that the device fits more tightly to the ice. In general, each fisherman modifies the device in his own way, making the device even more convenient and efficient.
DIY making
Some specialists can make a torpedo tackle themselves. To do this, make a wooden float about 15 cm long and weighing about 100 g . A lead plate is attached to the bottom, the weight of which should lower the product to a depth of 10 cm. A leash is made from a monofilament line with a diameter of 0.2 mm. It is tied to the main line, but just below the float. A fly 30 cm long and 0.2 mm in diameter must be attached to the leash. Then the side floats are fixed (length 9 cm, width 0.2 mm) at a distance of 30 cm from each other.
This device also quite effectively helps fishermen in their work. But, of course, to make it, you need to have certain skills and abilities.
The main advantages of a torpedo
Using a torpedo for winter fishing, the angler makes his work much easier. Thanks to this device:
Thus, a torpedo is a very effective assistant in the difficult work of a fisherman. It is especially difficult for a fisherman in winter due to weather conditions, and the device facilitates and speeds up the work process, helping to obtain a larger catch.
LED-based instrument lighting
It often happens that the dim factory backlight of the instrument panel confuses the instrument indicators or is not visible at all.
Also, due to such illumination, the driver’s eyes get tired, which can lead to an accident. The most modern method is LED lighting based on strips. Firstly, they are easy to buy at any auto store, and secondly, they are quick and easy to install. The first thing we need is to remove the instrument panel, depending on the make and model of the car, the panel is removed in different ways, so we will not describe the process of unscrewing and removing the panel.
Now, having removed the panel, unscrew it to the base, so that you can easily get to the standard lighting. As a rule, in passenger cars the power supply is 12V, the same power supply is used for the LED strip.
Next, you should be good with a soldering iron; you will need to remove the standard light bulbs and solder an LED strip in their place. As a soldering fastener, you can use two small wires, but not very thin ones; they can burn out due to the load. It is advisable to place the LED strip evenly over the entire surface. As practice shows, it is better to solder several short strips than one long one, and the likelihood of combustion is less, and there will be no load on one power supply.
If you are not comfortable with a soldering iron, then it is better to turn to experienced ones, since here you need to be careful and careful, the slightest short circuit can burn the entire instrument panel.
Once all the strips have been soldered, it’s worth checking, connecting the instrument panel with a surface-mounted installation and turning on the backlight; if everything is done correctly, all the strips will glow. The strips themselves can be attached using double-sided tape, so the backlight will be distributed evenly across all devices. All that remains is to put everything back together in reverse order, tighten the instrument panel and enjoy.
Fishing torpedo under ice - the best tackle in winter
Even in summer you often have to struggle with installing a network, let alone in winter. Punching several dozen holes, stretching a cord with a stick, and getting ice on all sides is very little pleasure. But progress does not stand still, and enterprising inventors came up with a very useful thing - a self-propelled fishing torpedo for pulling a line.
Description of the gear
An ice torpedo is a cylinder with a cone on one side. On the sides there are two gears with a diameter slightly larger than itself. Thanks to them, she moves underwater in the right direction. The teeth cling perfectly to the ice and prevent even a fairly strong current from blowing the device away from the course. There are two light bulbs on the top .
They are necessary for tracking during work and simplifying its search . One of them works while driving, the second lights up when stopping.
At the back there is a fastener for the cable and for the control. R20 type D batteries are used as a power source. 8 of these batteries provide about 2000 meters of travel under water.
Naturally, this distance may be shorter, since there will be obstacles underwater, which will require more energy to overcome.
Principle of operation
The unusual appearance may scare off a conservative fisherman, but in fact it is very convenient to work with it. According to reviews from experienced fishermen, it is convenient and practical to use. The entire network installation process is as follows:
When the entire measured torpedo cord goes under the ice , you need to pull it and thus stop it. The second light will light up. By moving in the direction of movement of the device along the light spot on the ice, you can quite easily determine its location. Due to the current or uneven ice, it may stray slightly from its original course, so it is advisable to monitor it from the very beginning.
If it has gone too far to the side or for some reason it is not possible to drill a hole above it, the torpedo can simply be pulled out using a cord and launched again. The design allows this, the main thing is to do it carefully and not break the wire cord. When a torpedo is located, a second hole is drilled slightly behind or above it. Through it you get the torpedo, and with it the cord. To do this as accurately as possible, you need to pour a bucket of water onto the ice, so it will become more transparent and the light source will be better visible.
As you can see, the process of pulling the cord is reduced significantly, labor costs are minimal, and efficiency is higher. What previously took several hours can now be done alone in an hour.
Self-tuning of the VAZ dashboard (33 photos)
Owners of VAZ cars often experiment with some parts of their cars, and the owner of this car, who decided to add exclusivity to the dashboard, was no exception. Since the guy considered the usual trim to be banal, he decided to make a new instrument panel himself.
PS We left the author's style unchanged.
the filling was made for the Kalina/Priora/21104 tidy that many are familiar with.
Using an iron, we “transfer” the toner from the sheet, which will cover the tracks from being etched by the evil ferric chloride. removing photographic paper ironed to perfectly smooth copper is a fascinating procedure; it’s better to fill yourself up with a sedative beforehand and turn on Enigma in the background.
We etch it, take it out, wash off the toner with acetone and are glad that we have a board. Having cunningly scratched the egg, the thought creeps in - well, all that remains is to solder it, and almost everything is ready! yeah.
have you ever cross stitched? I don’t, but I think it’s almost as exciting and exciting as drilling
200 holes with a drill, the size of a cockchafer's dick.
We solder the power supplies first, because if it’s anything - so here you go, a microcircuit with 64 legs and a price of 5 rubles per leg will have to be sent to the rats in the garbage chute to investigate the reason why it “broke in half” from 12V instead of 3.3V which I decided to give out the power supply. one of the blocks runs on the LM2596HV-ADJ chip. I once bought almost half a kilogram of them from the Chinese, I was glad that they were not expensive. So this miracle of Chinese industry with a loud sound decided to share with me the beauties of its inner world a second after turning it on. What is most surprising is that, having looked around the entire structure with a magnifying glass, I did not find a single reason for its proud Chinese hara-kiri.
