How to remove the rear bumper on a Ford Focus 3
Hello dear visitors of ford-motors.ru, today I have the honor to present another photo report. This time about how to remove the rear bumper on a FordFocus 3 station wagon with your own hands. I’ll skip the preamble about what and why the rear or front bumper is removed as written in this article.
In the first photo, circled in red is my reason for having to remove the bumper. Well, okay, I suggest we get straight to the point...
In order to remove the rear bumper on a third generation Focus you will need:
- L-shaped wrench head “7”, “8”.
- Screwdriver type TORX 30, flat screwdriver.
- Pliers or round nose pliers.
How to remove the front and rear bumper of a Ford Focus 3 (from the year)
Gearboxes also do not give owners any trouble. The suspension adequately copes with road surface defects, making trips enjoyable. It is moderately soft, which allows you to maintain the necessary balance between replacing the Ford Focus 3 bumper and handling. However, serious uneven road surfaces should still be driven very carefully.
And not only to save the suspension.
Among the shortcomings of the model, in addition to the rather cramped interior, one can highlight the low ground clearance. European versions have millimeter-level ground clearance. According to the manufacturer, on cars for the Russian market, ground clearance has been increased to millimeters. However, not all owners are comfortable with this Ford Focus 3 bumper replacement. Even small holes and ruts have to be driven very carefully so as not to catch the bottom on the road, and also not to damage the front or rear bumper.
On a country road, and even in a city where they have forgotten about road repairs, among other things, there is a very high risk of denting the threshold.
Well, the bumper is located in close proximity to the ground and is often the first to suffer. The car was clearly created for good, smooth roads. However, in Russia they are far from everywhere.
Therefore, a trip to the outback can bring unpleasant surprises. And going on a picnic can be overshadowed. It is not difficult to damage the bumper in the city.
To do this, it is quite enough to park unsuccessfully next to the curb. It is usually higher than the lower edge of the front bumper, so driving close to curbs is very dangerous.
What to do if the bumper is damaged?
If the defect is small and the part is not cracked, then repair will be quite possible. If a serious crack occurs, replacement will become necessary. A specialist will help determine the need for one or another option. However, the work of removing the bumper is easy to do yourself, saving money when replacing the Ford Focus 3 bumper. After removing the part, you can send it for repair, or you can purchase a new one.
Screwdriver type TORX 30, flat screwdriver. Pliers or round nose pliers.
Removing the rear bumper of a Ford Focus 3 - step-by-step instructions 1. Similarly, remove the remaining pins securing the front bumper to the radiator mudguard.
Replacing the bumper on a Ford Focus 3
This is how the pistons attaching the front bumper to the radiator mudguard are located. Remove the two bolts securing the side bumper to the front fender. Use a screwdriver to pry the piston securing the bumper side fastening clamp to the front fender. Remove the piston.
Carefully replace the Ford Focus 3 bumper with a plastic part, first disconnecting the wires from the fog lights. Assembly occurs in reverse order. The entire job of removing the bumper on the Focus 3 will take no more than an hour. As you can see, nothing complicated.
All about bumpers, repair, installation and removal
Passenger car manufacturers have simplified as much as possible the process of replacing body elements, which are most often subject to deformation and breakage. Removal of numbers; Removing the fastening bolts from the engine compartment; Removing external fasteners; Removing the bumper, taking into account the integrity of the mounting clips; Important! The process of replacing the front bumper of a Ford Focus 3 requires dismantling the headlights, behind which there is a connector with wires that should be disconnected during work.
Removing the rear bumper of Ford Focus 3 - step-by-step instructions
1. Unscrew the two thumbscrews on each wing and release the rear lights:
2. Using a socket on “7”, unscrew the six screws on the mudguards (three for each mudguard). Remove one clothespin along with the mudguard.
3. Pull the edge of the bumper to the side; under it there is a self-tapping screw for a TORX 30 screwdriver, which needs to be unscrewed.
4. Take out two pistons from the bottom and back of the apron. First, we take out the cap of the piston, 15 millimeters wide, and then we take it out entirely.
5. Now you need to unscrew the four screws of the doorway, two on each side.
6. Carefully pry the latches located in the area of the flashlight, after which you can remove the bumper.
7. The plastic damper cannot be removed because it is riveted to the body “to death”.
If, in addition to the bumper, you also need to remove the bumper amplifier, then for this you will need a “13” socket, with which you need to unscrew six nuts.
As you can see, there is nothing complicated, the whole process took 20-30 minutes.
Source
Removing the rear light for Ford Focus 3 sedan, video instructions
On a Ford Focus III, optical devices may fail due to prolonged use and mechanical damage. Drivers can avoid visiting a car service center by completing the entire procedure themselves.
On a Ford Focus III, optical devices may fail due to prolonged use and mechanical damage. Drivers can avoid visiting a car service center by completing the entire procedure themselves.
Replacing optical devices does not involve complex steps, so if you use the instructions, car enthusiasts will be able to complete all procedures without errors.
Preparing for removal
On the car of the presented sedan model, the rear light is divided into two sections. The process of replacing lighting devices is different on a hatchback and station wagon. The driver needs to prepare spare parts for replacement. If the lamp is seriously damaged, the spare part will have to be replaced completely. If just the lamp fails, it can be replaced separately. First of all, drivers need to disconnect the wire from the negative terminal of the battery in order to remove the mechanism.
Motorists replacing the Ford Focus 3 taillight if they prepare a standard set of automotive tools.
Dismantling the device
The replacement process is performed as follows:
- the nut securing the lamp section to the car body is unscrewed;
- the canopy section is removed from the body;
- the wiring harness connectors are disconnected;
- the optics section mounted on the wing is removed;
- the trunk lid trim is removed;
- the nuts and clamps securing the sections are unscrewed;
- the optics section is removed from the body;
- the wiring harness connectors are disconnected;
- the lantern is removed;
- a new or repaired device is installed;
- The installation process is carried out in reverse order.
The replacement process is not complicated, but motorists need to be extremely careful to avoid damage to parts and body elements. Work must be carried out carefully, and high-quality components, preferably original ones, must be used for replacement.
Video instruction
Motorists are recommended to use video instructions that will help you quickly and error-free replace optical devices on a third-generation Ford Focus.
Expert advice will ensure quick disassembly and high-quality installation of new devices.
As a result, drivers will be able to use new lighting technology when operating their cars. It is responsible for visibility on the road and safety, so worn parts must be replaced immediately.
Installing the rear skirt of Ford Focus 3
Task: install a Zetec rear skirt a Ford Focus 3
I ordered everything from different places: first the rear skirt, then the sills and the front skirt.
The front and sills are primed, the rear skirt still needs to be primed.
front skirt (1759505) rear skirt (1759541) side skirts (1759881 and 1759887)
I tried on the back skirt from zetec. As I wrote earlier, the Skirt is not original. It’s better to try it on before painting, you never know. Since this is not the original, you can’t expect that everything will come together, we had to modify it. Everything is in order: to try on a skirt you need to take off the bumper, to take off the bumper you need to take off the wheels:
started trying it on, oh here it started. The middle came together perfectly, but the transitions where the reflectors and the edges do not meet, the mustaches that are attached to the bumper are some thick, others large. , and off we go until everything unnecessary was removed, everything was adjusted, the bumper was installed and removed probably 300 times. but fortunately everything was done, everything came together. as it should be.
We cut a hole for the exhaust pipe, it is easy to cut, since there are notches. I only cut on one side, Bye. Then the exhaust will be double. I left a piece of cut plastic as a template, so that later I could make a hole. We also installed reflectors, there were also minor problems with them, we again solved the problem by sanding, they will have to be attached with 2-sided tape.
How to remove the rear bumper on a Ford Focus 3
Hello dear visitors of ford-motors.ru, today I have the honor to present another photo report. This time about how to remove the rear bumper on a FordFocus 3 station wagon with your own hands. I’ll skip the preamble about what and why the rear or front bumper is removed as written in this article.
In the first photo, circled in red is my reason for having to remove the bumper. Well, okay, I suggest we get straight to the point...
In order to remove the rear bumper on a third generation Focus you will need:
How to remove bumpers on a Ford Focus car in a garage
The second and third generations of Ford Focus are modern cars equipped with many devices and mechanisms that ensure the functionality and safety of the vehicle. One of the not the most difficult, but definitely the most important safety elements is the car bumper. The main purpose of this part is to soften the impact in an accident. Considering that bumpers take the main load under mechanical stress, manufacturers have provided the possibility of dismantling them for repair or replacement. Therefore, if your car has been in even a minor accident, it will probably be useful for you to know how to remove the front or rear bumper of a Ford Focus, so as not to spend extra money on visiting a car service center.
In this article we will tell you how to remove bumpers on Ford Focus 2 and 3 series cars
Removing the rear bumper of Ford Focus 3 - step-by-step instructions
1. Unscrew the two thumbscrews on each wing and release the rear lights:
2. Using a socket on “7”, unscrew the six screws on the mudguards (three for each mudguard). Remove one clothespin along with the mudguard.
3. Pull the edge of the bumper to the side; under it there is a self-tapping screw for a TORX 30 screwdriver, which needs to be unscrewed.
4. Take out two pistons from the bottom and back of the apron. First, we take out the cap of the piston, 15 millimeters wide, and then we take it out entirely.
5. Now you need to unscrew the four screws of the doorway, two on each side.
6. Carefully pry the latches located in the area of the flashlight, after which you can remove the bumper.
7. The plastic damper cannot be removed because it is riveted to the body “to death”.
If, in addition to the bumper, you also need to remove the bumper amplifier, then for this you will need a “13” socket, with which you need to unscrew six nuts.
As you can see, there is nothing complicated, the whole process took 20-30 minutes.
Ford Focus 2 Manual
We carry out work when repairing and replacing the front bumper. We carry out the work on an inspection ditch or overpass.
On a Ford Focus 2 with a hatchback body, we disconnect the wire blocks from the fog lights (see “Replacing the fog light bulb, removing the Ford Focus 2 fog light”).
Remove the mudguard of the radiator of the cooling system (see “Removing the radiator shield of Ford Focus 2”).
Using a Torx T-30 wrench, unscrew the lower...
...and the upper screws securing the right fender liner to the bumper.
Similarly, unscrew the screws securing the left fender liner to the bumper.
Using a Phillips screwdriver, unscrew the two screws for the upper bumper mounting to the upper cross member of the engine compartment.
From the bottom of the car, using a 10mm head, unscrew the two self-tapping screws securing the bumper to the right fender.
Similarly, unscrew the two bolts of the left fastening of the bumper to the fender.
We move the sides of the bumper away from the right and left wings, overcoming the resistance of the clamps.
Position of the lock on the right wing (for clarity, the headlight has been removed)
By prying up the right holder of the upper cross member of the engine compartment, we remove the bumper fixing tab from it.
Similarly, remove the left bumper tab from the holder.
By pressing the three bumper latches located in the center of the car, we remove them from the grooves in the upper cross member of the engine compartment...
...and remove the front bumper.
We install the front bumper of Ford Focus 2 in the reverse order.
Removing the front bumper Ford Focus 2
Site navigation
Primary source of content - WiKi of the Za Rulem magazine website
How to remove the rear bumper on a Ford Focus 3 (station wagon)? There's an answer!
Hello dear visitors of ford-master.ru, today I have the honor to present another photo report. This time about how to remove the rear bumper on a FordFocus 3 station wagon with your own hands. I’ll skip the preamble about what and why the rear or front bumper is removed as written in this article.
In the first photo, circled in red is my reason for having to remove the bumper. Well, okay, I suggest we get straight to the point.
In order to remove the rear bumper on a third generation Focus you will need:
Front bumper
Fastening the element is quite simple, and the part can be removed from the car with your own hands. The work is done by one person.
Step-by-step removal instructions
Before starting work, the vehicle must be placed on a horizontal base with a hard surface. Removing the front bumper on a Ford Focus 2 (restyling) should begin from the attachment points on either side of the car. After removing one corner, you need to move to the other side. The sequence of steps is as follows:
Installation
Installation of the repaired part is carried out in the reverse order. The order of work is as follows:
Removing the front bumper on a Ford Focus 3
Unlike Focus II, third-generation cars are equipped with a front bumper of a composite design, which includes two elements - an amplifier and a decorative trim. As a result of minor collisions, as a rule, only the pad is damaged, but in the case of more serious accidents, the amplifier also has to be replaced. If you find yourself in exactly this situation, then it would be useful to find out how to remove the front bumper of a Ford Focus 3, using only the tool that every car enthusiast has on hand.
You can do the dismantling yourself, but everything will be more efficient and convenient if you enlist the help of another person. Removal work is performed as follows:
- First, the car should be prepared, for which we remove the headlights, disconnect the end of the hood lift cable from the handle and subsequently remove it from the holder.
- Next, use a TORX T30 wrench to unscrew the bumper mounting screws and remove the holder, after which you can disconnect one side of the bumper. The same steps must be performed on the other side.
- The same wrench is used to unscrew the mounting screws located on the left and right.
- Now, having removed the clamps, we take out the four holders and unhook the brackets that secure the bumper.
- The final step is to pull out the bumper trim and remove it.
The removal process for the third model is similar to the previous version.
Before carrying out dismantling work, it is recommended to buy a set of holders, since they often break during the process and must be replaced.
Rear bumper
The plastic casing of the element on sedan cars is attached to two screws located under the lower edge of the trunk lid, two plastic clips on the lower edge of the bumper, two self-tapping screws under the decorative rubber trim and two nuts. The mounting pattern of the part is no different from that on cars with a hatchback body. The rear bumpers of the Focus 2 before and after restyling are identical in terms of attachment points and surface curvature, so it does not matter which rear bumper is installed on the car.
Removal
To dismantle the rear bumper on the Focus 2 hatchback, follow these steps:
Removing a similar part from a Focus 2 with a station wagon body does not have any fundamental differences.
Installation in place
The rear bumper on a Ford Focus 2 is installed in the reverse order. Damaged fasteners should be replaced. When installing parts, it is necessary to ensure uniform gaps between surfaces.
Removing the rear bumper on a Ford Focus II with your own hands
Was the rear of your car damaged due to a collision? Don’t rush to go to a car service center - just read the instructions on how to remove the rear bumper of a Ford Focus 2. This way you can quickly replace this body part, while saving a lot.
The dismantling process consists of the following step-by-step actions:
- First you need to remove the rear mudguards and fender liners on the right and left sides.
- Next, using a screwdriver, disconnect the power supply for the lights from the rear right.
- Using a screwdriver, disconnect the holder from the spar, then unscrew and pull out the pistons.
- Now you need to unscrew the screws located inside the wheel arches, and then open the rear door and also unscrew the fastening screws.
- By pulling the end holders, you can remove the rear bumper of your car.
This, in fact, is where the dismantling ends. In order to remove the rear bumper of a Ford Focus, you will need nothing more than a set of necessary tools, a few hours of free time and an assistant (which is optional). Further, all necessary operations to repair or replace this body part can be carried out.
Driving a car without bumpers is unacceptable, since this body part, in addition to its decorative function, ensures the safety of both the car itself and the driver and passengers in it.
Features of dismantling and installing third-generation Focus bumpers
To remove the front bumper of a Ford Focus 3, you will need two sockets (10 and 13 mm), a flat-head screwdriver and a Torx T30 socket. The procedure for dismantling parts is the same for machines of any configuration and is carried out as follows:
To remove the rear bumper on a Ford Focus 3, you will additionally need a 7 mm socket. The procedure itself looks like this:
Installing the part in its original place is done in the reverse order.
Source
Ford Focus 2 - removing and replacing bumpers
Replacing a bumper is a common procedure on any car, including the Ford Focus II. It is these parts that get chipped and scratched as a result of the car owner’s carelessness, and sometimes require more serious repairs. Local puttying and painting is possible, but removing cracks without removing the front bumper is hardly possible. In this material we will talk about how to remove the bumper on a Ford Focus 2.
