How to replace the air filter on a Ford Fusion with your own hands?

The purpose of a car air filter is to clean the air entering the working cylinders of the engine. Thanks to purified air, the quality of mixture formation is improved and the wear of contacting engine parts is reduced. For long-term engine operation, the Ford Fusion air filter must be replaced on time. The article contains information on how to carry out the replacement yourself and what you will need for this.

The air filter consists of a plastic housing and filter paper. For better placement of the filter material inside and a tight fit to the walls, it is sealed with special polymer rings. Passing through such a structure, the air flow is cleaned of dust and dirt particles, which prevents contaminants from entering the engine that could harm it.

Over time, the filter passes air worse as it becomes more and more dirty. Less air enters the engine to form air-fuel mixtures, and oxygen starvation occurs. This situation leads to the engine losing traction, the car becomes less dynamic, and it also affects the health of the driver and passengers. An error message may appear on the instrument panel. You can avoid such problems if you change the filter element on time.

Old and new air filters

Recommendations for replacement can be found in the vehicle manual, but you must take into account the conditions in which the car was operated. If the surrounding air is heavily polluted, then replacement is performed more often than the time recommended by the manufacturer. When operating under normal conditions, the filter is changed after 10 thousand kilometers, if conditions are severe - after 7-8 thousand kilometers.

It may be necessary to replace the air filter early, as it becomes unusable from accumulated condensation inside the housing, formed due to the constant temperature difference of the engine.

Air filter Ford Fusion

The air filter on a Ford Fusion car is designed to clean the flow of oxygen entering the combustion chambers.
Particles of heavy metals, salt vapors, dust, and dirt settle on the hygroscopic fiber of the cleaner. During the systematic operation of the vehicle, the amount of waste increases. It is more difficult for the engine to suck air into the combustion chambers, since obstacles to circulation are artificially created. The purifier needs to be replaced.

The fact that the time has come to replace the element will be indicated by such signs as: increased fuel consumption, passive acceleration dynamics, unstable engine operation.

Replacing the cleaning element on your own is not at all difficult, but be extremely careful not to violate the established regulations.

When and how often should you change the filter element?

Like any consumable item, the Ford Fusion air purifier must be changed at certain intervals. Untimely maintenance of the element creates negative aspects in the operation of the ventilation and air conditioning system. A heavily contaminated filter will be difficult to clean and pass air to the heater. The result is overheating of heating equipment in winter and failure.

In summer the situation is no better - the lack of a sufficient amount of air directly affects the level of workload of the air conditioning unit. The lack of cold air will increase the consumption of the combustible fuel mixture.

Ford Fusion manufacturers have established a schedule for replacing the cabin filter at 15,000 km.

Drivers know from experience that it is advisable to change an old part earlier than the recommended mark, at approximately 8–10 thousand mileage. What is this opinion based on? It all depends on the operating conditions of the vehicle and the environmental situation. The contamination of the filter material is affected by daily driving in city traffic, where the level of exhaust gases is greater than on country roads. Due to a dirty cleaning element, the cooling fan will work at the limit of its capabilities, causing rapid wear of parts and components.

Timely filter maintenance not only helps you save on expensive repairs, but also has a beneficial effect on the health of the driver and passengers inside the car. This is especially true for carbon multilayer cabin filters, which, by trapping harmful pollutants and volatile substances, protect the human body from exhaust gases and unpleasant odors.

How do you know when it’s time to change the cabin filter? There are several factors indicating this:

1. The air flow coming out of the dampers becomes less strong.
2. The deflectors show the appearance of remnants of vegetation and small debris outside the car.
3. When you turn on the air system, an unpleasant odor appears inside the machine.
4. The airflow cannot cope with fogged windows in damp, stormy weather.
5. As soon as you remove the dust on the plastic surface of the interior, it appears again.

When diagnosing a malfunction of the cabin filter, many drivers are guided by these well-known factors.

Where is the air filter located?

In the Ford Fusion, the device, which is supposed to filter the air entering the internal combustion engine cylinders, is located in a special plastic housing, which is located in the engine compartment. You will see this container next to the cylinder block. The filter element itself consists of a plastic base and paper that performs the cleaning function. The device is sealed with polymer rings, which ensures a tight fit to the walls. The air that passes through the filter device is cleaned of contaminants and dust particles. Thanks to this, dirt does not enter the power unit and does not interfere with its operation.

Air filter for Ford Fusion: price, articles, original, quality analogues

Characteristics:

• Weight 835 grams;
• Dimensions: 276 x 161 x 33 mm;
• Filler: paper with hygroscopic fiber, carbon impregnation, depending on the type of filter element.

DIY filter replacement instructions

You can replace the old Ford Fusion air filter at a service center, but the procedure is quite simple, so any motorist can perform it. Many drivers, using the manual, make the replacement themselves. Sometimes it is necessary to remove the air filter to provide access to other engine components, so gaining experience will not hurt.

What will you need?

To carry out the procedure you will need the following materials and tools:

• a new air filter if the old one cannot be cleaned;
• crosshead screwdriver;
• screwdriver
• 8mm socket wrench;
• key to 10;
• pliers;
• clean rag;
• devices for blowing with compressed air.

First of all, to carry out the replacement procedure, you need to lift the hood.

First, two corrugated pipes through which air flows are removed. The clamp holding the hose coming from the pipe, which is located on the air filter housing, is disconnected.

Disconnecting the air pipes and crankcase gas hose

The disconnected hose is removed to the side. The mounting clamps should be checked for integrity; if damaged, they must be replaced.

The next step is to remove the crankcase ventilation hose.

Dismantling begins by unscrewing two 10mm bolts in the front part of the housing.

Two bolts are unscrewed

After this, you should take the body by the back part closer to the windshield and pull it up. The case has two ears into which pins go, thanks to which it is held, so you have to pull harder. You can remove the left side first, and then the right.

When the case is removed from its seat, you need to turn it over and unscrew the 10 bolts that hold the cover. To speed up the process, you can use a screwdriver.

Unscrew the 10 bolts on the cover

After removing the cover, remove the filter element. If it is not very dirty, then it can be blown out with compressed air using a special device. When blowing through paper cassettes, you must be careful not to damage them.

Replacing the air filter for Ford Fusion 1.6 and 1.4

Thanks to the air filter, the air from which the fuel-air mixture is prepared in the engine does not contain dust particles. Foreign particles entering the engine significantly increase the load on it, thereby bringing its overhaul closer.

We recommend: What to do if the air conditioner in your car does not turn on?

Signs that it's time to change the filter:

• the car doesn't pick up speed well
• The engine periodically begins to “chop”
• the volume of fuel used increases
• in particularly advanced cases, the “check” warning signal may light up.

Since the price of an air filter is not high. We recommend regularly replacing this “consumable”. This will definitely cost less than eliminating the consequences of your forgetfulness.

Tools required for replacement: 10 socket, 25 torx (wrench or socket).

Procedure:

1) The air filter in the Ford Fusion is located in the decorative cover covering the engine. And in order to be able to do this, you need to remove this cover. To do this, you need to unscrew the bolts holding it and loosen the clamps holding the pipes.

2) Disconnect the air pipes from the cover.

3) Disconnect the breather located under the cover.

4) Carefully remove the engine cover. Try to do this evenly, as there is a possibility of breaking the clips holding the lid.

5) Transfer the lid and then turn it over. Unscrew the fastening bolts. There are 10 of them in total. Use tools prepared in advance.

6) After removing the bottom cover. Remove the used filter. Thoroughly blow out the housing in which the filter is located with a compressor.

Attention There is a crater gas filter next to the air filter. The main task of which is to prevent oil drops, oil evaporation and other contaminants from entering the pan. The crater gas filter is a piece of special foam rubber; some “experts” recommend replacing it with an ordinary sponge, but this is not true! Since such a “homemade product” will clog very quickly, which in turn will affect the ride quality. The best option is to purchase an original filter or an analogue

7) Install a new filter. Reassemble the cover and then install it in the reverse order of these instructions.

Replacing the air filter is a rather responsible process. Many car enthusiasts are concerned about the question of whether it is possible to replace the air filter on a Ford Fusion 1.8 with their own hands. Having understood this topic and armed with a simple algorithm of actions, it is possible to carry out this procedure quite easily and simply.

Candles

We take out (not tear out, but take out!) the spark plug tips from the spark plug wells, shaking them and turning them a little from side to side. If you have pneumatics, I recommend blowing out the wells for prevention. Take the spark plug wrench and unscrew the spark plugs. We take new ones and screw them in (without foolishness and screws.) with maximum force of the hand (and not the mighty biceps). We put on the tips. The VF box is installed in place. CAREFULLY screw in by hand, getting two screws into the “old” thread. Otherwise (this is another reason why I would not remove the VF box again):

We dock THREE pipes into place. Close the hood, wash your hands and go! *

PS: Additions on the instrument and some photos are mine, but later.

Selecting a filter

To replace the air filter in a Ford Fusion, the manufacturer recommends using only original devices, part numbers: 1729857, 1338536.

According to the technical regulations, the installation of similar devices is allowed:

• Blue Print AMD, item 52247;
• Alco MD-8020;
• Bosch, article number 1457433593;
• Mann S.

Our compatriots trust the last two analogues, since the products of these brands have proven themselves to be positive. When purchasing, you may be offered an Alco MS 6259 filter. It is not recommended to buy such a product, since it is thicker and will not fit into the seat.

DIY filter replacement instructions

You can replace the old Ford Fusion air filter at a service center, but the procedure is quite simple, so any motorist can perform it. Many drivers, using the manual, make the replacement themselves. Sometimes it is necessary to remove the air filter to provide access to other engine components, so gaining experience will not hurt.

What will you need?

To carry out the procedure you will need the following materials and tools:

• a new air filter if the old one cannot be cleaned;
• crosshead screwdriver;
• screwdriver
• 8mm socket wrench;
• key to 10;
• pliers;
• clean rag;
• devices for blowing with compressed air.

First of all, to carry out the replacement procedure, you need to lift the hood.

First, two corrugated pipes through which air flows are removed. The clamp holding the hose coming from the pipe, which is located on the air filter housing, is disconnected.

Disconnecting the air pipes and crankcase gas hose

The disconnected hose is removed to the side. The mounting clamps should be checked for integrity; if damaged, they must be replaced.

The next step is to remove the crankcase ventilation hose.

Dismantling begins by unscrewing two 10mm bolts in the front part of the housing.

Visual instructions for replacing the filter on a Ford Fusion + photo

Types of filters. The filter is usually changed a couple of times a year. For example, in spring and autumn. Different filters can be installed, in general they differ only in cost and manufacturer, but in terms of basic characteristics they are almost the same.

The procedure for changing the filter on a Ford Fusion is easy, containing some steps that we will explore in detail. To do this, you do not need to have any special skills or a lot of time. It only takes us half an hour to replace the filter.

1. Take a key for 10 and an asterisk for 20. picture:

Replacing the Ford Fusion air filter

2. First, remove a pair of air pipes and a hose from the filter housing, using light movements, without removing the clamp.

3. Unscrew the two upper bolts with a wrench.

4. Lift the filter up with both hands, grasping it by the body.

5. Unscrew the 10 screws using an asterisk, you can take a screwdriver or an electric screwdriver.

6. We take out the old filter by opening the housing.

7. Let's look at the two filters and conclude that it is difficult for air to flow through the old one.

8. Install a new filter, cleaning the housing from dust and dirt. We also change the crankcase gas filter.

9. You can use a dish sponge and use it as a filter.

10. Trim the sponge and install it so that it fits snugly against the walls of the hole.

Consequences of untimely replacement

If we consider the consequences of saving on an air filter, we can note the following:

• Reduced vehicle power.
• Contamination of the car engine, including further corrosion of the metal in the engine protection system.
• Deformation of parts inside the tank.
• Increased fuel consumption, which leads to increased cash costs.

Replacing the air filter on Ford Fusion 1.4 is available to every user. Also, do not forget about replacing the cabin filter element and checking the operation of the car engine in order to avoid possible malfunctions in the operation of the vehicle.

We fasten two bolts and put on two air pipes and a crankcase gas hose.

That's how easy it is to change the air filter on a Ford Fusion yourself. Thanks for the article to Pavel from

Eagle Car: Ford Fusion of the Year Other repairs on the topic: Now you need to remove the plastic trim, pull it towards you upwards, keep in mind that it is held on by rubber clips, so you will have to pull quite hard. When you replace the air filter on the Ford Fusion, turn it over, take TORX “25” and start unscrewing the bolts, all the bolts - When everything is unscrewed, the following picture will open in front of you - the air filter, as well as the crankcase gas filter.

Need for replacement

Signs of the need for replacement are visible to the driver with the naked eye. First of all this:

• Increased vehicle fuel consumption.
• Increased CO 2 level in the engine system.
• Visible contamination of the filter upon direct inspection.
• Reduced vehicle power.

How often should you change your air filter? Experienced specialists recommend carefully approaching not only the selection of the required filter element, but also the frequency of its replacement. First of all, it is worth remembering that every 10 - 15 thousand kilometers lead to contamination of the air filter system. This negatively affects, first of all, the overall performance of the car in city driving conditions. If the car is operated in extreme and difficult driving conditions, the air filter must be changed twice as often.

We recommend: How to properly flush a carburetor to restore its functionality: methods and means

Rules for choosing a new cabin filter

The original Ford Fusion car cleaner has its catalog number 1353269. This is a multi-layer carbon filter. Its cost is considerable, which is due to the originality of production. Therefore, the owners of this car are faced with a choice: take the original or look for its analogue.

There are a large number of substitutes from well-known manufacturers on the car market, which work well and are not inferior to the original part. Here are some of them:

• Mann;
• Bosch;
• Valeo;
• Knecht.

A feature of Ford is that on various modifications of the Fusion model, the dimensions of the cabin filter are not the same and they have to be selected. Useful information is provided in the vehicle owner's manual. The data can be found on the Internet on the automobile websites of Ford dealers.

A timely changed dirty filter element eliminates the formation and accumulation of bacteria in the car's air system.

Filter selection

The types of filters available for the Ford Fusion vehicle are quite varied. How to choose the right air filter? In order to carry out this procedure, you must focus on:

• The quality of the air element.
• Strength of the filter element gasket.
• Originality of the manufacturer.

You should not choose a filter based on the price category of the product. First of all, you should give preference to the original consumables from the manufacturer, which has a logo and all the necessary license marks.

Fuel filter

For FORD Fusion / Fusion Plus 1.4, MANN recommends the following filters: C 2244, W 7008, WK 511/2. You can see the detailed characteristics of these filters in our catalog.

Replacement intervals

On FORD Fusion / Fusion Plus 1.4 it is recommended to change the fuel filter every 100 thousand km.

If you are wondering which fuel filter to install on FORD Fusion / Fusion Plus 1.4, then MANN has taken care of you and has created a selection of filters from its catalogs specifically for your fuel system. Below is a list of fuel filters that you can install on FORD Fusion / Fusion Plus 1.4. The fuel filter is one of the most important filters; it has a high degree of purification and prevents small and large particles from getting into the engine along with gasoline or diesel.

Useful tips

• The clamp designed to secure the hose to the fitting on the air filter housing is disposable and must be replaced each time it is removed.
• When removing the air filter housing, remember that its rear part is installed on guides.
• The replacement air filter element has a rectangular shape, and it completely matches the shape of the air filter housing. Therefore, it is not possible to install the filter element into the housing incorrectly.

HYUNDAI repair in St. Petersburg

We carry out HYUNDAI repairs of any complexity. Call us now

• Maintenance
• Engine overhaul
• Changing the engine oil
• Camber toe

HYUNDAI Maintenance

Timely maintenance not only allows you to maintain the car in good condition, ensuring the normal operation of all vehicle systems, and extends its trouble-free service life, but is also often one of the conditions for maintaining the manufacturer’s warranty. Detecting and correcting faults at an early stage allows you to avoid more serious breakdowns. Professional diagnostics and vehicle maintenance at our auto repair shop allows you to save not only time, but also your money.

You can find out the cost of servicing your car and make an appointment with us for a car service by calling +7 (921) 638-45-45

HYUNDAI engine overhaul

Engine overhaul is one of the most complex repair operations associated with the operation and repair of foreign and domestic cars. Requires high professional skills of specialists performing this procedure.

HYUNDAI engine repair can be divided into several stages:

• Diagnosis and identification of the cause that led to the malfunction
• Disassembling the engine and compiling a list of spare parts that need to be replaced
• Checking the condition of the cylinder head for geometric parameters and microcracks
• Coordination with the client of estimates of spare parts and repair operations
• Ordering spare parts necessary for repairs
• Repair and installation of the engine on a car, including changing the engine oil
• Final settings and tests of engine parameters

The cost of engine overhaul depends on many parameters and is determined for each specific case.

Changing the engine oil

Periodic Maintenance

Periodic maintenance is a mandatory and necessary condition for the long-term proper operation of each car. Timely replacement of engine and transmission oil, fluids, filters, wearing parts (drive belts, brake pads, etc.), diagnostics of the condition of units and components, and other activities included in the list of works depending on the mileage and age of the vehicle, help to insure from troubles on the road, serious breakdowns, and ultimately reduce the costs of the car owner.