KGB FX-5 2-WAY: Instructions and manual in Russian

Instructions for use and installation of the system...

Page 3

Image
Text

KGB FX-5 “Instructions for use and installation of the system”

ver. 2

© Saturn Marketing Ltd.

CONTENT:

SERVICE FUNCTIONS

Remote deactivation and activation of the shock sensor 21 Control of the central locking from the key fob when the ignition is on 21 Automatic control of the central locking from the ignition key 21 Car search mode

Driver call

Turbo timer operation

Monitoring vehicle condition and interior temperature 22 Selecting the duration of confirmation beeps and the type of alarm beeps 22 Valet service mode

Monitoring the health of limit switches 23 Control of additional channel No. 1 (remote unlocking of the trunk) 23 Control of additional channel No. 2 (programmable function) 23 Control of additional channel No. 3 (programmable function) 23 Two-step unlocking of door locks 24 Control of additional channel No. 4 24 LED status indication alarm

ENGINE STARTING

Rules for the safe use of the engine starting system 25 Preparing to start an engine with a manual transmission 26 Remote engine start 27 Remote engine runtime extension 27 Automatic engine start based on temperature 27 Daily automatic engine start 28 Preparing the vehicle for movement 28 Remote engine stop 28 RPM learning procedure idle speed 28
PROGRAMMING FUNCTIONS AND OPERATING PARAMETERS
Recording key fob codes

Programming operating modes using the service button 29 Programming system functions 30 Restoring factory settings of programmable system functions 30 Table of programmable functions 31 INSTALLATION INSTRUCTIONS

Safety regulations

Recommendations for placement and installation of components 33 Connecting the power 6-pin connector 35 Connecting the 18-pin connector 36 6-pin connector for connecting electric door locks 39 MAINTENANCE

STORAGE, TRANSPORTATION, RESOURCE, DISPOSAL

42
SUPPLIER GUARANTEES
42

MAIN UNIT CONNECTION DIAGRAM

Instructions for use and installation of the system...

Page 4

Image
Text

KGB FX-5 “Instructions for use and installation of the system”

ver. 2

© Saturn Marketing Ltd.

SYSTEM FUNCTIONS

Congratulations on purchasing a KGB class security system! This system is designed to last for many years without the need for repair or replacement. only be installed

an authorized dealer with the appropriate certificate.

Protective functions of car alarms

♦ Activation of sound and light alarms when sensors are triggered in security mode ♦ Providing alarm alerts on a key fob with an LCD display ♦ Remote activation of the “Panic” mode ♦ Immobilizer mode ♦ Anti-robbery mode, activated remotely by the key fob ♦ Anti-robbery mode, activated by a special button ♦ Engine blocking and its preservation when dismantling the alarm system

Car alarm service functions

♦ Silent security mode ♦ Security mode with the engine running ♦ Silent activation/deactivation of the security mode ♦ Activation of the security mode without a key fob ♦ Automatic re-arming ♦ Automatic (passive) arming ♦ Delayed activation of the security mode while the interior light goes out ♦ Self-diagnosis when turning on / off the security mode ♦ Remote shutdown / activation of the shock sensor by levels in security mode ♦ Remote control of the central locking ♦ Control of the central locking from the ignition switch ♦ Two-step unlocking of door locks ♦ Double-pulse unlocking of door locks ♦ Possibility of implementing the “Comfort” function ♦ Service mode “ Valet” ♦ Emergency disabling of the security mode with a personal code ♦ 4 additional channels for controlling vehicle devices ♦ Control of vehicle interior lighting ♦ Vehicle search mode ♦ Remote programming mode for new key fobs and erasing lost ones ♦ Possibility of resetting the values of programmable functions to factory settings ♦ Driver call mode ♦ Temperature indication inside the car ♦ Time display, timer, alarm clock ♦ Main key fob battery discharge control via LCD display

Engine starting functions

♦ Remote starting and warming up of the engine ♦ Automatic starting and warming up of the engine by temperature and timer ♦ Remote or automatic stopping of a running engine ♦ Selecting the engine type: gasoline / engine ♦ Selecting the transmission type: automatic / manual ♦ Selecting the starter cranking time when starting ♦ Control of engine operation based on signals from a tachometer or generator ♦ Indication of operating time of a running engine on the key fob display ♦ Remote extension of operating time of a running engine

Setting up KGB TFX 5 alarm

The instructions for use describe several programming options:

Control key fob buttons.
Protective and energy-saving functions.

Control key fob

Writing a sequence of commands to the system memory is done as follows:

the key is inserted into the ignition;
press the service mode button until 4 beeps sound;
to bind the key fob, you need to hold down the first 2 buttons until the siren sounds;
After these manipulations, the key can be removed from the ignition.

To program the first button on the key fob, do the following:

Press the key with the image of the sun several times - this will move the cursor around the screen.
Place the cursor next to the required command.
Press the button with the image of the sun for 6 seconds until 2 siren signals sound, and then after a while 3 more.

Other keys are configured in the same way. The system can be given settings using the service mode button, for this:

You need to insert the key into the ignition, after which you need to press the Valet button (service mode) 6 times.
The machine will beep 6 times.
With help. Valet keys select function.
Use the buttons on the key fob to set the desired value.
After setting, the ignition can be turned off.

This is interesting: How to choose durable winter tires for your car? 3 main selection criteria

The energy saving function is activated as follows:

by pressing the sun button and holding it until a signal sounds;
after which the cursor on the screen points to the word Save;
The mode is started using the first button of the key fob, and turned off - the second;
In order to exit the setting mode, you must hold down the sun button until a sound signal appears. After which a battery icon will appear on the screen.

To configure protective mode:

Start the car engine.
Press and hold the right button on the remote control until the side lights flash (3 times), an exhaust gas icon and an engine operation timer will appear on the key fob.
After setting, you need to remove the key from the ignition. If everything was done correctly, the motor will not turn off.

To restore factory settings, you need to:

Turn on the car ignition.
Press the service mode button 10 times.
Turn off the ignition and wait until the siren sounds 10 times. This means the system is ready to reset.
Press the emergency button once, a beep should sound.
Click the right button on the key fob, after which the system settings will be reset to factory settings.
To exit the mode, you must turn on the ignition.

Programming the protection function

To enable the protection mode when the engine is running, you need to:

put the car on the handbrake;
Press and hold the right button on the key fob until the remote control emits a signal. After which the exhaust gas icon and engine operating time will appear on the display;
after which the ignition can be turned off, and if everything was done correctly, the power unit will continue to operate;
within 30 seconds you need to leave the car and lock all the locks. Press the right key fob button and wait for the siren to sound. A lock icon will appear on the remote control screen.

When this mode is activated, the ignition control function will be disabled.

To emergency enable the protective mode (without a key fob) you need:

Turn on the ignition.
Press the service mode key seven times.
The system should beep.
Remove the key and leave the cabin within 20 seconds, the door locks must be closed.

To emergency turn off the protective mode (without a key fob):

Open the door with the key, and the alarm will work.
Start the car engine.
Press the service mode button 4 times within 20 seconds.
Turn off the ignition, the siren will stop working and the turn lights will blink twice.

Instructions for use and installation of the system...

Page 6

Image
Text

KGB FX-5 “Instructions for use and installation of the system”

ver. 2

© Saturn Marketing Ltd.

RULES FOR THE SAFE USE OF CAR ALARMS

This security system (car alarm) is a complex electronic device. Installation, connection and configuration of the car alarm are described in detail in the “Installation Instructions” and can be carried out by the consumer in full independently. However, the manufacturer strongly recommends that you entrust this set of works to a service center certified according to GOST R 51709-2001 (OKUN 017613), which specializes in installing alarms and/or additional electronic equipment in cars (hereinafter referred to as the certified service center ). The car alarm is designed for stationary installation on a vehicle, powered by its on-board network with a voltage of 12 V DC, the negative pole of the battery is connected to the vehicle ground. Before installing a car alarm on a car, first connect all the wires to it in test mode, make sure that all connections are made correctly, connect power from the battery and make sure that the car alarm is working properly. If installing a car alarm requires drilling holes or any other changes to factory parts of the car, be sure to first consult with your nearest dealer about the correctness of such intervention in the design. Never install the car alarm central unit where it will become very hot, for example from direct sunlight or hot air from the car's heating system. Also avoid places where the central unit of the car alarm and its components will be subject to strong vibration, or where they will be exposed to dust or dirt. Use only the fasteners included with the car alarm installation kit. In this case, the installation will be reliable and safe. The use of parts not included in the car alarm installation kit may lead to disruption of its normal operation. When washing a car, it is unacceptable for water and detergents to get on the surface or inside the central unit of the car alarm, on its components (siren, sensors, antenna module, limit switches), as this can lead to damage to the car alarm. To ensure moisture protection, it is advisable to initially install car alarm components in places inaccessible to the flow of liquids and splashes, and if necessary, take precautions during washing or cover (wrap) the components with available household waterproof material, for example, plastic film, etc. Never insert any objects into the central unit of the car alarm or its components to avoid damage to the electronic units and systems. In the event of a suspected breakdown, do not try to open the car alarm housing (its components) yourself, and please avoid entrusting diagnostics and/or repairs to incompetent persons. If the car alarm is faulty, contact a certified service center. Cleaning. Do not attempt to clean the key fob or other car alarm components with any harsh liquids, solvents or chemicals, as this may deteriorate its appearance. To clean, use a clean, dry cotton cloth (soft brush). Due to the constant work to improve car alarms, increasing its reliability and improving performance characteristics, minor changes may be made to the design that are not reflected in these Instructions.

Specifications

Temperature conditions of normal operation: for the pager - 0... +400°C, siren - -30... 850°C, the system itself - -40... +850°C.

The alarm works with no more than 4 transceivers.
Using the system, you can organize 6 security zones.
Operating currents in active mode are minimal - up to 25 mA.
Supply voltage - 12 V, from the on-board network.
1200 m - radius of operation of the receiver in open areas.
600 m - two-way communication range between the key fob and the car.
The KGB TFX 5 alarm system with auto-start operates at a frequency of 433.5 MHz.

Instructions for use and installation of the system...

Page 9

Image
Text

KGB FX-5 “Instructions for use and installation of the system”

ver. 2

© Saturn Marketing Ltd.

FUNCTIONS OF SYSTEM TRANSMITTER FOBS

Buttons 3 + 1

♦ Selecting the key fob alert mode (press and release the buttons simultaneously

And

)

Buttons 3 + 2

♦ Quickly set the key fob timer (press and release the buttons simultaneously

And

)

PURPOSE OF THE BUTTONS OF THE ADDITIONAL (SINGLE-SIDED) KEY FOB

Button 1

♦ Arm/disarm (press and release) ♦ Channel 3 control (press and hold for 3 seconds)

Button 2

♦ Starting and stopping the engine (press and release) ♦ Extending engine run time (press and hold for

3 seconds)

♦ Activating the security mode while the engine is running (press and

hold for 3 seconds)

Button 3

♦ Search mode (press and release) ♦ Trunk release – channel 1 (press and hold for 3

seconds)

Button 4

♦ Silent arming/disarming (press and release) ♦ Channel 2 control (press and hold for 3 seconds)

Buttons 1+2

♦ Panic mode (press and release the buttons simultaneously

And

)

Buttons 1+3

♦ Disabling the sensor (press and release the buttons simultaneously

And

)

Buttons 1+4

♦ Enabling the Valet service mode (press and release the buttons simultaneously

And

)

Buttons 2+3

♦ Enabling the temperature trigger mode (press and release or hold the buttons simultaneously for 3 seconds

And

)

Buttons 3+4

♦ Anti-robbery mode (with
on
, simultaneously press and release or hold down

within 3 seconds of the button

And

)

♦ Recording a key fob in programming mode (press and hold simultaneously for 3 seconds

buttons

And

)