How to remove the original radio on a Ford Focus (Mondeo) 3

Step-by-step instruction

To remove the radio from a Ford Focus 3, released in 2012, you must perform the following steps:

1. First, disconnect the terminal from the negative pole of the battery, de-energizing the on-board network.
2. Use a spatula to remove the plastic cover located between the climate control unit and the lower part of the decorative trim of the head unit. The panel is attached to plastic latches; first, the fastener is removed from the right side of the part, and then it is removed from the left mounting socket.
3. After the owner has removed the plug, it is necessary to unscrew 2 screws. The operation is performed with a screwdriver or electric screwdriver.
4. Pull the frame that contains the control buttons and air ducts towards you. After the clamps are released, the assembly should be moved a short distance from the plane of the dashboard. Disconnect the wiring harness plug going to the head unit control buttons.
5. Remove the head unit of the audio device, secured with 2 screws. After removing the screws, carefully pull the product out of the guide grooves, and then disconnect the wiring and antenna plugs.
6. To replace or repair the LCD information display, you will need to unscrew 4 screws and disconnect the connection connector.

When installing additional elements, such as an AUX connector, you should remember that the electronic modules of the Ford Focus 3 are connected via a digital CAN bus.

To ensure functionality, it is necessary to make adjustments to the software using a computer connected via an ELS27 cable.

Some Focus cars were produced without a standard connector, but activation of the device is not required.

After the restyling, a radio tape recorder unified with the Ford Mondeo began to be used, the removal algorithm changed. Need to:

1. Remove the plastic cover located under the speaker unit.
2. Remove the plug located next to the glove compartment lid. The element is installed tightly; use a plastic card to remove it.
3. Disconnect the element located around the gear shift lever. Initially, you need to remove the clip located in the center, then the right fastening is released, and lastly the left fastener is unfastened.
4. Remove the overall central panel together with the gearshift lever and the climate control unit. The unit is fastened with latches; dismantling is carried out carefully, since there is a risk of losing fasteners.
5. Remove the front panel with control buttons and central air ducts, which is secured with 2 rigid latches.
6. Proceed with dismantling the housing of the standard Ford Focus 3 radio, which is secured in the instrument panel with 2 screws.
7. Then the power plugs and antennas, which are equipped with plastic latches, are disconnected.

Assembly is carried out in reverse order. If the owner does not have experience, it is recommended to contact a service center.

Ford Focus Hatchback III Black Cat › Logbook › Change the radio? There are options!

Even before buying the car, I regretted that cars with a radio a la MyFord
(with
a large display
and many
multimedia capabilities
) were not supplied to the Russian market.

The offered radios come with a 1 year warranty.

(installation, for those who don’t want to dig - too).

I corresponded with an official dealer in St. Petersburg, here is its content: Author: I would like to ask whether the MyFord Touch system will ever appear on the Russian market in the near future to replace the standard radio of the Ford Focus 3? If it appears, I would like to know when and at what price

.
And if it doesn’t appear, can you recommend a device that is similar in function
, but is not yet offered in the dealer network?

Dealer response: At the moment, MyFord navigation is only expected on cars in Russia, there is no exact information yet. Other manufacturers of navigation systems are still developing a suitable system for the Focus 3 model. In particular, the popular DVM8500 system (DVM8530 - author's note) from the Phantom manufacturer was expected in May, but now the deadlines have moved to June. We are waiting for information from the manufacturer in the near future; among our clients there are many Focus 3 owners who want to install this system.

Author: You mentioned the DVM8500 system from Phantom. This is a rather interesting system in terms of functionality. In this regard, the question is: from the point of view of the official service, do you impose any restrictions on the installation of this system in a warranty Ford Focus 3 vehicle?

?
For example, can I install it myself or at one of the many service centers that install audio/video equipment in cars? Or, say, only at the service center of a Phantom representative in St. Petersburg? Or, for example, only in the service of your dealer network? This issue is of interest from the point of view of maintaining the warranty on the electrical equipment of the car
. And an additional question: when these systems come to market, will they be offered as an accessory in your dealer network or only through third-party sellers?

Dealer response: There are no restrictions on the installation of this system.

in terms of warranty.
Yes, you can install this system not only at an official Ford dealer, but also at any other service center
.
When this system appears, it will be sold from us and installed accordingly
.

Here is such an interesting correspondence (this is to answer the questions of many that supposedly “will be removed from the guarantee”).

And here is another letter from the officials: Unfortunately, at the moment, the original MyFord Touch multimedia system is not available for order! As an analogue, we can offer you a non-original one, called MyDean 7191, with basically the same functionality. The cost of such a multimedia system is 36,000 rubles.

Relevant topics on the FF3 forums: 1. FFClub.ru 2. Focus3.ru 3. Ford Touch. This thread doesn't really like the MyFord system. It seems to me that analogues are better: worse quality, but better functionality! There are maps, traffic jams, videos, and much more!

Several drivers have already installed similar devices: 1. PSH. His article. 1. SANDER35. His article.

Here are a couple of videos from Youtube. Chinese radios (ordered from there, or rather). First video:

Source: www.drive2.ru

How to remove the original Ford 6000cd radio

I believe that you have heard the question more than once about how to remove a 6000cd radio on a Ford Focus 2. Also, a 6000cd radio was installed on Ford Fusion, Ford Fiesta and some Ford Mondeos after 2005. The 6000cd radio is also in my 2006 Ford S-max.

Sony 6000cd radio in Ford S-max interior

This radio is called Sony 6000cd because the manufacturer is Sony, but it is also called Ford 6000cd because it is installed mainly in Ford cars.

So, how to remove a 6000cd radio. The fact is that this device, unlike others, has special latches so that it would not be easy for robbers to remove it. These locks can only be unlocked with special 4 keys. The keys have a certain shape, but you can easily make them yourself, even from a plastic card.

Marking a card for creating keys for a Ford 6000cd radio

Key blanks made from a plastic card for removing a Ford 6000cd radio

Keys from a plastic card for removing the Ford 6000cd radio

Steel and plastic key for removing Ford 6000cd radio

I want to say that the card should be plastic, not laminated paper. Because once I got good keys from the card, and I left them with the new owners of the Ford Fiesta. And in the last case, from a new card, after trying to insert them into the locks, my keys simply delaminated and I had to make good iron ones from a hacksaw blade.

Keys for removing radio Ford 6000cd

Removing the Ford 6000cd radio with a key

Removing the Ford 6000cd radio with a key

Removing the Ford 6000cd radio with a key

Removing the Ford 6000cd radio with a key

Well, we are in the salon and ready to remove. We insert 4 keys into the slots on the front panel of the radio. They should go all the way in and bend the latches inside (See photo).

Removing the Ford 6000cd radio with a key

Removing the Ford 6000cd radio with a key

Then we carefully try to pry it from the end and push it towards us. You can remove the plastic cover of the volume control (the large knob in the middle) and gently pull the rod towards you. If everything is done correctly, the radio will move forward without much effort.

Radio removal tools

If you decide to change the original radio in the Ford Focus 2 to another, you need to stock up on the following tools.

1. A screwdriver with a star or hex shaped tip, since different models have different fastenings.
2. A plastic card such as a credit card.
3. Stationery knife.
4. Manufacturers have a special key to remove the tape recorder. It is called FORCE F-910C1 490.00. In shape it resembles one half of scissors with holes. With its help, removing the radio from the socket takes two to three minutes. But it costs between $10-20. In addition, it is not so easy to find and purchase. And you also need four of them at once. But there is no need to despair. Our person will find a replacement for any thing, not just a simple key. There is an alternative for them. You can make them yourself, and they are very easy.

First way

To do this, you need to find two pairs of scissors and simply divide them into two parts to make four keys.

Second way

It is not difficult to make such keys yourself. The process of making keys for removing the radio from a Ford Focus 2 is as follows.

1. Take an unnecessary plastic card.
2. Cut into 4 slices approximately 2cm wide.
3. At one end, cut a corner at 45 degrees.
4. The keys are ready. We saved at least $40.

The content of the article:

How to remove the original radio in a Ford Mondeo

In order to remove the standard GU in a Ford Mondeo

we will need:

How to remove the radio on a Ford Focus 3

Some cars come complete with standard multimedia devices ✔. Drivers often have a question about how to remove the radio on a Ford Focus 3. Dismantling may be required if it is necessary to replace or repair the device. You also have to remove the radio when installing auxiliary components, for example, the AUX connector.

Standard devices

Now we present a list of car radios that are considered standard for the Ford Focus 3. They are able to fully satisfy the needs of the average car audio lover, as they are equipped with almost everything necessary.

Note. Do not forget that the sound quality depends little on one car radio. If a music lover wants to get the highest quality sound, he will have to modify everything: speakers, noise insulation, cables and wires, and much more.

Parrot Asteroid Smart and its review

Ford Focus 3 car radio

This is a complete complex device with excellent head control, designed for installation in Ford. The Android operating system (see 2 din car radio for Android: which is the best) and some features of this car radio distinguish it from its analogues. The main thing is that this device is designed in accordance with the interior design of this car. It integrates perfectly with the standard equipment of the Ford Focus 3 and its interior design.

Differences

The radio is equipped with good navigation, including licenses for PROGOROD, Yandex.Navigator and other well-known maps. Navigation Parrot Asteroid Smart is compatible with Navitel, Android applications, etc.;

Technical capabilities

Step-by-step removal process

The process of removing the radio from a Ford Focus 3, produced before 2012, includes the following steps:

• removing the negative terminal of the battery (the part is first loosened with a wrench or pliers);
• removing the decorative trim located between the climate control unit and the lower part of the lining of the electronic control device (plastic elements are pryed off with a spatula, removing the clamps on the right side and removing the trim from the mounting holes);
• removing 2 screws located under the removed cover (this action is performed using a screwdriver or a screwdriver with a Phillips head);
• removing the frame holding the air ducts and controls (it is necessary to disconnect the latches and pull the part towards you; after removal, the frame is moved to a distance of 10-15 cm from the dashboard);
• disconnecting the cables connected to the control elements of the head electronic unit;
• dismantling the car radio casing, secured with several screws (screws are unscrewed with a screwdriver or screwdriver);
• removing the audio device from the guide channels, disconnecting the cables and antenna;
• LCD screen repair (to disconnect the display, you need to unscrew 4 bolts and disconnect the connector).

In Ford Focus and Mondeo cars produced after 2012, the car radio is removed as follows:

• the plastic panel located under the speaker system module is dismantled;
• remove the plug located near the glove compartment lid (the element is installed firmly, so you will need a plastic spatula to remove it);
• the cover that hides the base of the speed selector is detached (first, open the clip located in the middle part, then disconnect the right fastener, the last step is to remove the left fastener);
• the central panel is removed along with the gear knob and the air conditioning control device (the unit is held on by clamps, it must be removed carefully, trying not to damage the fasteners);
• the front panel with control keys and air flow distribution devices is removed (the parts are held on by 2 latches);
• The radio casing is removed from the seat (the audio device is held in the dashboard with 2 screws that need to be removed);
• the power cables and antenna, the connectors of which are equipped with plastic clips, are disconnected.

Search

Take off radio Ford Focus 2: there are two options

Ford Focus cars came with Sony 6000 CD. Remove the headlight on the Octavia A5. Since the Skoda is not equipped with the ability to remove the shelf above the climate control. Before the restyling, 4 slots were used for installation, after which a “transition frame” was installed. Taking off this can be done without a special tool, but it just gets damaged. How to replace a plate in a Ford Escort station wagon? It comes out of the oven, how to remove the door. Before take off radio

, on “Generation 1” focus 2 you need to record and adjust the volume. And you can make a special tool yourself.

Where to look for slots? The answer is in the video.

Extraction wizard enabled Ford Focus 2 2008 edition

First, 4 fasteners are fastened: the plates are placed in the grooves “on the face”. Cutouts on plates to look inside.

Top left slot

Installation order: 2 lower, then 2 upper. The headlight is secured with 3 bolts and is clearly visible when looking at the latch on the bumper. The first 2 bots too. The third inner side is on the side (if you forgot to secure it, you can remove the headlight without additional ones. Press each plate until it clicks.

Radio pull the cymbals to your ears. And if they are not there, then the regulator shaft. To do this, remove the volume knob - secure it with screwdrivers and the like.

Usually the focus 2 radio was removed to install something else. Surprise: the antenna connector is not quite standard.

Remove the original radio for Ford Focus 3 2012

Breeding radio

for Ford Focus 3 Ford Focus—
3
1317.

To remove the radio Ford Focus 3 Remove the disk and secure the cable Ford Focus 3

Good video on how to remove the radio

on
Ford Focus 3
and remove the disc from the drive and fix the loop in the magnet.

There are ready-made adapters.

The antenna connector is first disconnected from the housing, then from the main one. How to remove UAZ Patriot radio | The assembly continues in reverse.

Set of tools

The branded kit is called FORCE F-910C1 490.00. The Ford ignition is stuck, I repeat the question! How to remove the larva if focus 2 too. The price is the highest. How to remove a radiator without removing the Ford Escort panel. But pullers can be made by drawing.

4 pullers are required at once.

articles

• 1387728 — black radio frame;
• 1509717 — Black frame for climate control;
• EEC GV3301 is equivalent to this: F-910C1 490.00.090417.

Extraction wizard enabled Ford Focus 2 after 2008

Insert 4 plastic cards under the outer frame as shown.

The part is pulled towards itself and removed. Then unscrew the 4 screws - this is the radio installation. A T25 wrench can come in handy, but for many it's just a cross.

Radio

unplug, unplug antenna cable and more.

The main thing is not to lose the screws when loosening.

articles

• 1539347 — air conditioner frame (silver);
• 1547160 is the same as climate control.

What problems may arise

When dismantling and reinstalling the device, it becomes necessary to enter a code located in the car radio's memory. Disconnecting the audio system from the power source for more than 15 minutes will result in a lockout. The next time you turn on the device, you will be prompted for a password, without which it will not be able to operate.

Dismantling the radio for subsequent replacement does not cause any problems. In other cases, the work must be completed as quickly as possible. If there is no card with a code, you need to contact the dealership, visit a special company, or try to find the password using programs.

Auto parts for foreign cars, auto repair

Initially, you need to remove the clip located in the center, then the Ford Mondeo 3 removal of the radio mount is unclenched, and last of all, the left clamp is unfastened.

Remove the overall central panel together with the gearshift lever and the climate control unit. The unit is fastened with latches; dismantling is carried out carefully, since there is a risk of losing fasteners. Remove the front panel with control buttons and central air ducts, which is secured with 2 rigid latches.

Ford Mondeo 3 radio removal to dismantle the body of the standard Ford Focus 3 radio, which is secured in the instrument panel with 2 screws. Then the power plugs and antennas, which are equipped with plastic latches, are disconnected. Assembly is carried out in reverse order. If the owner does not have experience, it is recommended to contact a service center.

Instructions for removing the door trim on a Ford Focus 3

17.10.2019

Ford Focus has been produced by Ford Motor Company since 1998. The model immediately entered the market in three body styles. Remaining for many years one of the best-selling brands in Russia and the CIS, drivers are faced with a large number of problems, among which repair of door speakers takes 3rd place.

How to remove the door trim of a Ford Focus 3 in order to repair internal electrical systems or replace old plastic? Detailed instructions are provided below.

What is door trim and its purpose?

The door panels on the Ford Focus sedan station wagon and hatchback of the first generation were made of durable but thin plastic. The material had good resistance to mechanical damage and did not crack from frost. The owners noted a characteristic creaking of the trim in the armrest area.

The interior of the third Focus uses higher quality materials - high-strength plastic and eco-leather. The doors are lined with color-matched plastic panels. Purpose:

• ensuring sound insulation of the cabin;
• protection of electrical cables from mechanical damage and rapid operational wear;
• technical review when checking electrical cables;
• decorative function, soft plastic is not only reliable, but aesthetically pleasing and beautiful.

The layout principle of the door pockets on Focus 3 is identical to the first generation. Removal and installation of new front door panels remains the same for any body type. The only difference in the third generation is the new clips or trim fasteners, which are reshaped and made of a hard polymer.

Dismantling

It is quite possible to dismantle the casing yourself. Many drivers encounter difficulties due to incorrect work procedures. Removing the door trim on a Ford Focus 3 is necessary in cases where:

• rear or front door glass needs to be replaced;
• The power window does not work;
• the door lock does not close well or is faulty;
• The driver's speaker stopped working;
• It is necessary to improve the sound insulation of the cabin.

Source: https://infokuzov.ru/tuning/obshivka-na-ford-fokus-3

How to remove/pull out the standard radio.

For owners of passenger cars, this security system, in addition to the troubles associated with restoring the functionality of the device after each more or less long disconnection from the battery power supply system, does not bring. And although it is easy to recover the Ford Mondeo radio code, repeating the code entry is quite irritating.

How to find out the Ford radio code? There are several options: Read the device's operating instructions. Restore using the serial number of the radio, which is indicated on the back panel of the device. How to remove the standard radio. Then contact the dealership with a request.

Call for help from specialists who deal with similar problems with burglars. It should be noted that this specialty has practically become obsolete due to massive thefts of audio equipment from car interiors.

Why is the radio blocked?

When creating the Focus model, Ford developers used many both successful and questionable decisions. One of them was protection against theft of the radio - blocking all functions if it stops feeling power.

Car radio code entry operation: first attempt

For the United States, this idea was quite successful, but in Russian realities such security measures turned out to be unnecessary. The code must be entered after each preventive maintenance of the vehicle.

How to Remove the Original Radio for Ford Mondeo 3

What tuners for Ford Mondeo?

Since the development of the Ford Mondeo project, the American company has been considered a universal (global) car. That is, a car is for sale all over the world, regardless of the regional characteristics of the sites. Thus, two generations of the Ford Mondeo were put on the road. But, unfortunately, as often happens, the developers' expectations were not met. Oh, and that would be stupid. Unfortunately, it is very difficult to name the brand of a car factory (regularly) assembled, which is very difficult for the local conditions of the region in which it will be sold. If at all possible. And who, if not the residents of Russia, should know about this.

Cassette player

in a Ford Mondeo

Model features

Abandoning a tempting but unattainable goal (which, incidentally, had contributed to poor Mondeo sales worldwide and particularly in the US), Ford commissioned the development of new changes in the company's local divisions. In Europe, this task was assigned to Ford Germany. In the Ford Mondeo 3 and 4, to be precise, all changes and improvements were made almost entirely thanks to the appearance of German engineers.

Ford Mondeo 3 and 4 models are currently not available. But thanks to the reliability, level of comfort and relatively low price of a car in this class, they are still in demand in the secondary automobile market. And we will meet on the track Mondeo 3, 4 and even earlier versions. often.

Radio pin

The coding system for tape recorders, created in the 1990s to counteract the mass theft of car audio equipment, has long lost its relevance. But it is still constantly installed by OEMs. This security system, with the exception of problems associated with restoring the functionality of the device after each more or less long disconnection from the power system (battery), does not provide it to car owners. And although it is very simple to recover the Ford Mondeo audio system code, repeating the encryption is quite annoying.