Signs of wear and contamination of the filtration system
The driver needs to focus on the main signs indicating the exhaustion of the resource:
- excessively frequent fogging of windows - occurs in the process of taking in cold air flows;
- interruptions in the operation of the heating system and climate control equipment of the Ford Focus - a sharp weakening of flows at maximum power indicates the need to replace the cabin filter;
- the appearance of sharp unpleasant odors emanating from the Ford Focus engine compartment.
Choosing a cabin filter
The original filter, which is installed on the conveyor (and is also supplied to official dealers as a spare part for maintenance), has article number 1709013. For a carbon filter, the original is not so expensive (its price is about 700 rubles), but it has excellent quality: its elasticity makes it easy to twist it is without damage so that it can be conveniently inserted into the compartment.
However, many owners, especially those who drive a lot (and, accordingly, often service the car), prefer more common and affordable analogues.
A classic example is the domestic TSN 9.7.876 and Filtron K1350, Fram CFA11642, MANN CU 25007yu are distinguished by decent quality. A number of filters from well-known brands (Bosch, Mahle) in the retail network are even more expensive than the original - it’s hardly worth recommending them, the overpayment will not be recouped by the resource .
Operating procedure
The cabin filter is located under the hatch located on the right side of the Ford Focus dashboard. You will need to pry off the cover with a screwdriver and remove the plastic clip, subsequently detaching the trim that hides the center console. It is necessary to unfasten the locking latches located on the right and remove the cover that prevents access to the part to be replaced.
The exhausted Ford Focus cabin filter is removed from its seat. The internal surfaces are thoroughly wiped with a rag to remove any dirt and dust that has accumulated during operation. The FordFocus 3 cleaning component is replaced, followed by fixing the latches and installing the removed parts in the reverse order.
Which oil filter is better?
How to replace the cabin filter on a Renault Duster
For FORD Focus III 2.0, MANN recommends the following filters: C 16 134/1,W 7015. Detailed characteristics of these filters can be found in our catalog.
Replacement intervals
from 7 to 15 thousand km, but not more than 12 months. The oil filter on FORD Focus III 2.0 is replaced along with the oil.
Which oil filter to install on FORD Focus III 2.0, let's answer this question together. To begin with, we note that on the FORD Focus III 2.0, as in general on any other car, the oil filter performs a very important task - cleaning the oil. Oil filters are changed along with the engine oil, which means its service life is very short, only about 10,000 km. The oil filter evens out the composition of the oil and prevents foreign particles from being in the oil of your FORD Focus III 2.0. The most effective and best filters are those from MANN, which have already proven themselves on the market. Below is a list of oil filters that are suitable for FORD Focus III 2.0. There are a huge number of offers on the market from different companies, so it is logical that car owners have a question about which filter to install and which one will be better for FORD Focus III 2.0. We chose MANN, since this company offers the largest range and makes its filters from high-quality materials.
Brief characteristics of MANN W 7015
- Applications:
Passenger cars - Price:
395 - Item price:
952168 - Filter type:
Lube oil - Barcode (EAN):
4011558044220 - Delivery Status:
Delivered - Filter wrench:
LS 7 - UGV 1:
1.40
Replacement process
So, with our own hands we change an element of the interior cleaning system:
First you need to open the hood. Now take a flathead screwdriver and use it to carefully remove the fasteners on the plastic cover
This must be done carefully, as the latches are too fragile (especially if you replace them in cold weather).. Filter location in Ford Focus 1
Filter location in Ford Focus 1
Disconnect the fasteners, remove the gasket and look at the old cleaning system element. Then pull the front side of the element housing towards you and remove it. Let's take a new component, the arrows on its body indicate the direction of air flow, install it so that the arrow shows the downward direction. It is necessary to check the correct installation. The component must be installed accurately in the housing, there should not be large gaps on the sides. Close the front wall of the component.
New filter in Ford Focus 1
Replacement process
Replacing the air cleaning component in the restyled Ford Focus 2 itself is not a labor-intensive task, so even the most inexperienced driver can cope with it. The main thing is to follow the instructions provided and carry out all the steps exactly.
If you replace the cleaning element in a timely manner, you will get the following results:
- the engine's operating life increases;
- the vehicle's power increases while driving;
- normal operation of the exhaust system;
- saving gasoline.
Tools
The manufacturer recommends replacing the air component together with a crankcase gas cleaner. Therefore, we will consider the process together with the change of this part. Before you begin the actual replacement, prepare everything you might need:
- a wrench or a socket wrench with an extension to “7”;
- the air filter itself (the brand of the original element is Mahle LX 1780);
- rags;
- new crankcase gas filter;
- liquid VD-40;
- Phillips screwdriver.
Tools for replacing VF on Ford Focus 2 restyling
Self-replacement of the element
- First you need to open the hood and find the air cleaning component housing cover.
- Then you need to unscrew the 4 bolts to remove this cover.
- Take a socket wrench with an extension to “7” and unscrew this bolt. You can try to do this with a regular key, but using a head will be much more convenient.
- Now you need to unscrew the two mounting bolts of the air duct and move the pipe. This is done for greater convenience so that the pipe does not interfere with the removal of the old and installation of a new filter element.
- We will immediately change the crankcase gas cleaning and ventilation component. You just need to pry it off with a screwdriver and pull it out, installing a new one in its place.
Crankcase gas filter for FF2 restyling
- Next, pull the cover up and remove it. It can be installed firmly, so you will need to apply a little force to dismantle it.
VF Focus 2 after a run of 15 thousand km
- This is what the VF looks like after 15 thousand kilometers. You, as the driver of the vehicle, must make a visual assessment of the condition of the element. If, after a mileage of 15 thousand km, the element looks deplorable, then the replacement interval must be reduced. Then you yourself will know how often you need to change the VF.
- Now you need to dismantle the cleaning component and wipe its body from settled dust.
- We take a new VF and install it in the connector. Before doing this, take VD-40 fluid and lubricate the inner ring of the filter. In order for the rear part to fit neatly into the guides, it will need to be compressed a little.
New VF at installation site
- Now you can put the cover back in place and tighten the bolts back. Be sure to check that the back of the element fits correctly into the housing.
- Screw the pipe into place.
Important! Don't think that you can save money by blowing out the filter with a compressor. It is advisable to blow out the element if the vehicle is temporarily used in difficult conditions and the component itself has not yet exhausted its service life
A little trick: at the installation site, mark with a marker or on a piece of paper the date and mileage when the VF was changed.
Features of cabin filters
Replacing the cabin filter yourself is easy. But before you “climb” into it, you need to buy a new element.
Naturally, it is better to purchase an original cleaning element, although it is more expensive.
But the auto parts market is quite extensive, so you can find a cheaper and non-original filter.
It is only important that the item being purchased is suitable in size and intended for this car. Now a little about the filters themselves
They are available in two types - dust and coal.
Now a little about the filters themselves. They are available in two types - dust and coal.
The first of them is made from cellulose; it provides good air purification from foreign impurities.
The carbon filter is also made of cellulose, but it is impregnated with activated carbon.
The presence of carbon particles allows such a filter not only to purify the air, but also to neutralize harmful chemical compounds. Therefore, for drivers with allergies it is better to use just such a filter.
But the carbon element has its own peculiarity. Neutralization of harmful substances is carried out by retaining them with coal particles. But over time, these particles become so saturated with these substances that they no longer retain them and they begin to actively enter the cabin.
Therefore, the service life of a carbon element is shorter than that of a conventional dust element.
Having purchased a new consumable, you can begin to replace it. In addition to this, you will also need two things:
- A screwdriver with interchangeable bits (you will need either a Phillips bit or a T15 Torx);
- Rags.
Selection of air filter for Ford Focus 3
The original Ford filter 1708877 , it can also be found under the number 1848220. The cost of the original air filter is from 650 rubles and more, depending on the region. If you are not ready to pay that kind of money for a filter, you can take a closer look at analogues.
Analogues of Ford 1708877
- AWM EA0106 (USA)
- BIG Filter GB9320 (Russia)
- Filtron AK3721 (Poland)
- Fortech FA027 (Korea)
- Goodwill AG251 (UK)
- Mann C161341 (Germany)
- Sakura EA19710 (Indonesia)
- SCT Germany SB2188 (Germany)
- Nevsky filter NF4022 (Russia)
As you can see, there is a huge selection of analogue filters on the market. The above list is far from complete. When choosing an air filter, we advise you not to purchase filters that are too cheap, as they are often of poor quality and clog much faster.
How often should I replace it?
The FF3 cabin filter operates in poor environmental conditions. This is an item that needs to be replaced every 6 months. This need arose for several reasons.
Firstly, after the period of use has expired, the throughput speed of the part decreases, thereby aggravating the microcirculation of cabin air. This creates humidity and makes the windows sweat.
Secondly, the cabin filter (particularly carbon) absorbs many toxic chemical components and after six months of use begins to release them back into the air. Therefore, failure to comply with the deadlines for replacing the cabin filter can have negative consequences.
Experts recommend reducing this figure by half and replacing it every 12 thousand km. It is better to follow the average of these two standards and make a replacement in accordance with the road conditions in which the car is driven, the frequency of its use, and the time of year. If you live in a village and drive on a dirt road in the summer, then the cabin filter should be replaced after 8 thousand km.
