Replacing and selecting a battery for a Peugeot 308

The battery installed by the manufacturer for the Peugeot 308 is designed for 4 years of operation (indicated in the technical documentation). In the future, it must be replaced with a compatible one at a service center. You can also make the replacement yourself, but in this car this is done by partially disassembling the plastic engine compartment casing and removing the air filter.

How to remove the battery on a Peugeot 308

How to remove the battery on a Peugeot 308
The car battery requires some care and maintenance. This becomes especially important when cold weather sets in, since the device needs to be recharged. The same should be done if the car is left idle for a long time in a garage or in a parking lot. On many models you can remove the battery in a couple of minutes, but there are exceptions to the rule.

The Peugeot 308 is proof of this. Often, owners of this vehicle experience some difficulties, spending a lot of time, effort and nerves. Even the included instructions, in which everything is written rather vaguely and incomprehensibly, does not help to remove the battery on a Peugeot 308.

Indeed, access to the battery is blocked by all kinds of decorative, protective and technical elements. However, there is no need to despair. Let's try to figure out the sequence of actions on how to remove the battery on a Peugeot 308, and after several attempts this task will be solved without difficulty.

The first thing you need to do to remove the battery on a Peugeot 308 is to open the hood. Then you need to remove the decorative cover covering the engine and exhaust manifold.

The next obstacle is the air filter. We loosen the clamp, press the latch at the bottom right and carefully remove this part in the casing from the grooves.

It may not work the first time, but the main thing is not to make sudden movements, and eventually the air intake will be dismantled.

Now that access to the battery is free, you need to remove the cover from it. This will allow you to remove the positive terminal. Near the wire with the positive terminal there is a wire that needs to be unscrewed. For this we use a 13″ wrench.

Then we pull out the connector, which is located near the wire we just unscrewed. These manipulations allow you to easily remove the fuse box. You just need to pull it up.

We place the block in the right side of the inter-hood space.

Let's start removing the casing from the battery. To do this, carefully remove the latches that are on the right and left of the casing, then hook it by the lower part and pull it up.

The next step will be to remove the negative terminal, as well as unscrew the battery mounting bolts. To do this, we use a 12mm tubular wrench. We remove the battery for maintenance or replacement.

Assembly is carried out in reverse order. When installing the battery in place, you have to tinker with installing the cover. It must fit completely into the grooves of the fasteners, otherwise it will wobble.

How to light a Peugeot?

1. To light a Peugeot, open the hood and drive the donor car as close as possible to the recipient.
2. The engines of both cars must be turned off.
3. First, to light a cigarette, a cable from plus to plus is connected from the donor car.
4. The negative cable should be grounded on the Peugeot body.
5. Wait a few minutes, this will allow the recipient's car battery to partially charge.
6. Then the engine of the donor car starts, you need to wait about five more minutes. After this, the power unit is turned off, and you need to try to start the Peugeot. If you fail to start the engine, you should repeat the procedure again, just wait longer. As a result, the Peugeot engine should start.

Reasons for battery failure

Every owner of a Peugeot 308, sooner or later, a situation may arise when he needs to change the battery in his car.

A battery can fail for various reasons. Among them are:

• Service life has expired.
• Improper operation or storage, etc.

Before choosing a new unit, it is important to know how to do it correctly so that it lasts for a long time. It is also important to know how to properly remove the battery from the car itself.

Battery cost

If the battery fails, it must be replaced with a new one. Buying a native battery will cost 5,600 rubles. Experienced car owners advise that it is better to take a closer look at batteries from third-party brands.

They have an attractive price, long service life and excellent performance characteristics. The best battery options from third-party brands are presented in the table below.

Table - Estimated cost of batteries for Peugeot 308

Rules for removing the battery for a Peugeot 308

Location of the battery and negative terminal under the hood.

The following tools may be required to remove the battery:

The Peugeot 308 has the following battery:

• Size: 278x175x190 .
• Capacity: 77 Ah .
• Reverse polarity.

Reverse polarity only!

Removal stages

1. Remove the decorative cover under the hood.

The decorative cover is marked with an arrow.

The battery protection cover is indicated by an arrow.

Unscrew the clamp and remove the latch from the filter grooves.

The fuse box is key 13. The terminal has already been removed.

Down with the negative terminal. The photo shows the bolt securing the battery to the body.

The arrows indicate the battery mounts.

At this point the work can be considered completed. If you have certain skills, you can deal with it in about 20 minutes. After this, the battery is charged or taken to a service station for diagnostics. Then assembly and installation is done in the reverse order.

Video about replacing the battery on a Peugeot 308 (carefully vertical)

Battery: what could it be?

Deciphering the inscriptions on the battery.

The most common currently are lead-acid batteries.

They work due to a chemical reaction that occurs inside. This type of battery can be maintained (topping up antifreeze and water), or it can be maintenance-free. There is no need to pay attention to maintenance for those batteries that come in a sealed case. The disadvantage of such devices is that they have a small capacity, as their design does not allow it.

Modern batteries run on electrolyte in the form of a gel. All of them are not serviceable.

Dry charged battery

When you need to buy a battery for the future, it is recommended to buy a dry charged one. This can be activated at the right time if you add electrolyte to it.

Those batteries that are filled at the factory can be used immediately after purchase. They are prepared by masters. Such units have an advantage, namely, that they are charged at the factory using special equipment while maintaining all parameters, which guarantees the durability of such a battery.

How to choose a battery?

If you don’t know which battery to install in your Peugeot, then you need to consider several criteria before purchasing. Let's look at them in more detail.

Options

When purchasing a product, you need to pay attention to the following points:

1. Device dimensions. This is a very important point, because if the device is larger, there is a chance that you will not be able to install it in the seat. Every car owner who has ever installed and removed a battery knows about this. Depending on the year of manufacture and engine type, battery dimensions may vary. Dimensions can be 19x24.2x17.5 cm, 19x20.7x17.5 cm, 19x24.3x17.5 cm, 19x27.8x17.5 cm
2. The main parameter that needs to be taken into account when purchasing is battery current . In Peugeot cars, again, depending on the engine type and year of manufacture, this parameter may differ. It can be 75-80 Ah, 70-75 Ah, 60 Ah, 52-62 Ah. This parameter can be clarified in more detail in the service book. If this information is not in the manual, then inspect the case of the battery installed in your car - the current strength should be indicated on it.
3. Another important criterion is the polarity of the device. Peugeot cars use direct polarity, but some cars are equipped with a battery with reverse polarity; when purchasing, it is important not to confuse it. The bottom line is that on reverse polarity devices, the plus and minus are swapped, and accordingly, difficulties may arise when connecting, since there may not be enough wire.
4. Starting current. It can also be different; you need to check exactly in the service manual or check the parameters of the installed battery.

Photo gallery “Battery malfunctions”

How to remove and replace the battery on a Peugeot 308 - step-by-step instructions

The battery must ensure reliable and quick engine starting in any weather and in any frost. Unfortunately, its service life is limited and depends on a lot of different factors, including the number of consumers on board the car. What kind of battery is installed on the Peugeot 308 from the factory and which one is better to choose for replacement, you will have to think after the first two or three years of operation of the car.

In today's article I will tell you how to independently remove and replace the battery on a Peugeot 308 in case it is discharged or fails.

What to do if the battery is dead?

First of all, when the battery dies, it can be impossible or very difficult to start the engine in the morning. Check the amount of charge inside the battery with a multimeter. It controls the voltage at the battery terminals. In addition, you can carry out this procedure without tools - using the indicator. It is built into almost all modern batteries. Green color indicates full charge, and red indicates no charge.

But it is more correct to identify a weak battery in a Peugeot 308 by elimination. For example, if after measuring the voltage at the battery terminals the tester shows low voltage, the culprit may not always be the battery. The same result is observed when there is a current leak or a generator malfunction. Therefore the following is done:

• start the engine using any of the following methods;
• the machine is operated all day, in between the engine stops should be short, no more than 1.5 hours;
• In the evening, readings from the terminals are taken again.

If the voltage when the internal combustion engine is running is approximately 14 V, and when the engine is stopped - 10-11 V, the generator can be excluded from the “suspect” link. He is OK. Then the current needs to be checked a third time the next day, in the morning. The same indicators with the engine stopped will eliminate current leakage in the network. This means the battery is definitely faulty.

Battery for Peugeot 308 – which one to choose

The battery powers the vehicle's on-board network when the engine is stopped, and also provides energy to start the power unit. During operation, the battery wears out and its capacity decreases. Therefore, after 3-7 years you may need to purchase a new battery.

Peugeot does not manufacture its own batteries. She makes purchases from manufacturers, which are presented in the table below. At the same time, power supplies from Fiamm are predominantly installed on cars going to the domestic market.

Tips for choosing

When choosing a battery, both native and third-party brands, you should first of all pay attention to what market the car is designed for. This is due to the fact that the batteries differ significantly in size and are not interchangeable.

An important criterion is the battery capacity. Slight differences from the original battery are allowed. A significant difference will lead to suboptimal battery operation and a decrease in its service life.

According to the manufacturer, when choosing a battery, the most important parameter is the starting current. Its recommended values ​​are shown in the table below.

Table - Approximate recommended starting current depending on the volume of the Peugeot 308 power plant

The main reasons for the failure of the Peugeot 308 battery

The following factors can be considered the main reasons for the failure of batteries on a Peugeot 308:

• Damage to the battery case and plates
• Closing the plates
• Open battery internal circuit
• Sulfation of plates

In most cases, if the battery fails, there is no need to run out and buy a new one. You can contact special services and find out if it is possible to repair the old battery

Replace Peugeot batteries at affordable prices in Moscow

The battery, which is equipped with all modern cars, is designed to ensure that the engine starts in any conditions. In addition, it supplies power to various systems responsible for safety, comfort and control of the units. The energy storage device is maintained in working condition by special components that guarantee the required parameters. The supply of electricity for further storage in the battery is carried out through wires from the generator, and a special electronic unit regulates the voltage and charging current. The health of the charging system is monitored using a light on the dashboard.

How to replace the battery on a Peugeot 308 – step-by-step instructions + photos

In order to remove and replace the battery on a Ford Focus, we need to perform the following procedure:

1. Open the hood and remove this cover.
2. We take out the air filter by clicking the latch on the bottom right of the filter.
3. Remove the battery cover.
4. Disconnect the positive terminal of the battery upwards.
5. Near the positive terminal wire, unscrew the other wire with a wrench.
6. Next, disconnect the white terminal.
7. We take out the fuse block by pressing the latches on the top and bottom of the block
8. We remove the wires and the block next to the right side of the engine. Let's leave it there for now.
9. Completely remove the battery protective casing.
10. If necessary, unscrew the negative terminal.
11. Unscrew all battery fasteners.
12. And we take out the battery. We replace it with a new one if necessary or send it for charging and install it in the reverse order.

Battery replacement algorithm

Before removing the Peugeot 308 battery for subsequent replacement, you must wait until the engine has completely cooled down (40 minutes after turning off the ignition). You should also check whether the battery is charging when the engine is running. If the indicator of no current from the generator lights up on the dashboard, then the first step is to check the fuses.

To remove the battery and then replace it with a Peugeot 308, you will need the following tools:

• wrench with heads 10 and 13;
• turnkey extension cord.

Under no circumstances should the procedure be performed at sub-zero ambient temperatures. As practice has shown, the plastic parts of the engine compartment casing in the cold burst from the slightest pressure on them. At temperatures above +5℃ such problems do not arise.

Removing the battery is carried out as follows:

1. Turn off the engine, turn off the ignition and all other electrical appliances, and open the hood.
2. Remove the decorative cover. It is held on by 3 latches and is located slightly to the left of the battery.
3. Pull out the air filter housing by pulling up the latch at the bottom.
4. Remove the battery protection cover, under which the positive terminal is hidden. It is not held in place by anything; it is pressed against the previously removed decorative covers.
5. Using a 13 socket, disconnect the wire next to the positive terminal (goes to the fuse block). It will also be possible to remove it with a regular open-end wrench, but it will be inconvenient and there is a possibility of damaging the protective plastic insert of the fuse block.
6. Loosen the terminal on the positive wire and remove it.
7. Remove the fuse box. It is secured with two latches. There is no need to pull it out by force: if you break the plastic latches, it will not be easy to get a new case; they are also quite expensive.
8. Remove the second terminal, next to which there is a minus sign.
9. Completely remove the battery protective housing.
10. Unscrew the battery fasteners. There are a total of 3 nuts at the bottom of the compartment; you will need an extension cord, since without it your hand cannot reach it (although an open-end wrench fits).
11. Remove the battery.

This instruction is relevant for the Peugeot 308 2010 model. In 2011 the only difference is that it has its own housing for the fuse box, it comes with 3 brackets. Then all that remains is to replace the ABK with a new one; installation is performed in the reverse order. The battery must first be charged.

So, replacing the battery in a Peugeot 308 is not as easy as in a VAZ. Access to the battery is prohibited here; partial disassembly is indispensable. The most difficult thing in all this is not to break the plastic fastenings of all the casings and decorative inserts. The entire procedure will take 20–30 minutes.

Reasons for battery failure

Every owner of a Peugeot 308, sooner or later, a situation may arise when he needs to change the battery in his car.

A battery can fail for various reasons. Among them are:

• Service life has expired.
• Improper operation or storage, etc.

Before choosing a new unit, it is important to know how to do it correctly so that it lasts for a long time. It is also important to know how to properly remove the battery from the car itself.

Malfunction in the power system

The internal combustion engine power supply system is carried out by supplying fuel to the cylinders from the gas tank using a fuel pump. Depending on the type of power plant (gasoline or diesel), there are slight differences, but the principle of operation and malfunctions are almost the same. In a conventional fuel system - with a fuel pump, pipelines, throttle valve, etc., you can try to figure it out at home.

• Fuel pump malfunction. If the pump does not pump fuel from the gas tank, then you can try to blow out the tube going from the tank to the gas pump.
• Loose connections in the fuel line fittings lead to fuel leakage and air leaks. After tightening the fittings, the fuel leak should stop.
• Poor quality fuel.

Rules for removing the battery for a Peugeot 308

Location of the battery and negative terminal under the hood.

The following tools may be required to remove the battery:

The Peugeot 308 has the following battery:

• Size: 278x175x190 .
• Capacity: 77 Ah .
• Reverse polarity.

Reverse polarity only!

Removal stages

1. Remove the decorative cover under the hood.

The decorative cover is marked with an arrow.

The battery protection cover is indicated by an arrow.

Unscrew the clamp and remove the latch from the filter grooves.

The fuse box is key 13. The terminal has already been removed.

Down with the negative terminal. The photo shows the bolt securing the battery to the body.

The arrows indicate the battery mounts.

At this point the work can be considered completed. If you have certain skills, you can deal with it in about 20 minutes. After this, the battery is charged or taken to a service station for diagnostics. Then assembly and installation is done in the reverse order.

Video about replacing the battery on a Peugeot 308 (carefully vertical)

Battery: what could it be?

Deciphering the inscriptions on the battery.

The most common currently are lead-acid batteries.

They work due to a chemical reaction that occurs inside. This type of battery can be maintained (topping up antifreeze and water), or it can be maintenance-free. There is no need to pay attention to maintenance for those batteries that come in a sealed case. The disadvantage of such devices is that they have a small capacity, as their design does not allow it.

Modern batteries run on electrolyte in the form of a gel. All of them are not serviceable.

Dry charged battery

When you need to buy a battery for the future, it is recommended to buy a dry charged one. This can be activated at the right time if you add electrolyte to it.

Those batteries that are filled at the factory can be used immediately after purchase. They are prepared by masters. Such units have an advantage, namely, that they are charged at the factory using special equipment while maintaining all parameters, which guarantees the durability of such a battery.

Characteristics that you should pay attention to when replacing the battery

A battery with optimal parameters under the hood for a Peugeot 308.

These include:

1. Starting current . This refers to the current that the battery can supply to the starter. On most modern batteries this indicator is designated DIN. It is closest to GOST, and therefore it is worth choosing batteries with this marking. You also need to remember that the larger the battery has this value, the faster and stronger it will crank the starter. It is also worth knowing that increased current can simply burn the starter or wiring.
2. Capacity . It is measured in Ampere hours. The higher this indicator, the longer the battery will be able to expend its energy and turn the starter. The car manufacturer recommends installing only those batteries on the Peugeot 308, the models of which can be found in the vehicle's Owner's Manual. If you do not take this parameter into account and buy a cheaper battery, then such a battery may not function well in the cold season. It is also not recommended to buy a battery with a high rating, since it will also not last long because it will not be fully charged.

Is there air conditioning?

It is important to pay attention to the additional consumers that are in the car. If, for example, an air conditioner is installed there, then it is worth buying a battery that has more Ampere hours than stated by the car manufacturer.

Riding style

You must also remember about your driving style. If the car drives a short distance after starting and then remains at rest for a long time, then the battery will not have time to charge and will soon fail. This is important, especially in winter.

Battery polarity and features

Peugeot 308 has reverse polarity!

You also need to pay attention to the polarity. It may be changed in some battery models. In this case, the terminal wires on the car may not be enough for connection.

need to look at the plugs , since gases may be released from the battery during operation. The plugs must have holes for this. More expensive battery models have special valves, while inexpensive ones have simple holes that can become dirty during operation.

Weather

It is also worth paying attention to the weather conditions in which the car will be constantly operated.

This also affects the service life of the battery. You also need to pay attention to road conditions. Although this indicator is not particularly important, it is worth remembering that if there is strong shaking in the battery, the plates may short out.

Quality and manufacturer

Varta battery and original. Varta from below.

The quality of the battery is one of the important parameters.

It is known that now there can be many fakes on the automobile market that are not distinguished by their durability. There are several points that will help distinguish the original from the fake. This:

1. Manufacturer country . This should be indicated on the battery case. But the manufacturer’s address must also be there.
2. Date of manufacture .
3. Data sheet for the battery.
4. A good case without flaws or dents (high-quality plugs, beautiful and smooth terminals with caps and other points).

Replacing the battery on a Peugeot 308 and caring for it

The battery should be replaced in the following cases:

• Doesn't hold a charge.
• Doesn't charge at all.
• Mechanical damage to the housing.

Before winter, it is recommended to check the density of the electrolyte and recharge the battery.

In order for the battery to serve properly for a long time, its charge should be periodically checked. If the car is driven frequently and for a long time, then such a battery does not need additional recharging. When the car is idle for a long time, you will need to disconnect the battery terminals and check the charge (once every 20–30 days).

You should avoid completely discharging the battery. This may negatively affect its performance. In this case, the service life will also be significantly reduced.

Peugeot: 4007, 408, 307

Selecting and replacing a Peugeot 4007 battery is a very responsible and serious issue. A large amount of electronics, with which a car is literally crammed, places special demands not only on the make and model of the battery, but also on the operating conditions and frequency of use of the “filling”. The Peugeot 307 is the undisputed leader in its class in terms of interior volume, trunk volume, and amount of equipment. The best choice, if you need to replace a Peugeot 307 battery, would be a Bosch battery or one from the Varta Silver series.

The innovative development of the Anglo-Russian enterprise Giver 60 ampere/hour can withstand a large number of charging and discharging cycles, and practically does not lose energy even during long-term storage. Increasing the charge retention time by 4 times and preserving the battery's performance after being in a state of deep discharge, after a long time, is the undoubted advantage of Giver. It is recommended to replace the Peugeot 408 battery with an Ecostart 6 CT-60 NR, which in terms of price belongs to the “economy” series. Reliable design, optimal performance characteristics and high power parameters have a positive impact on improving the serviceability of the Peugeot 408 of previous years.