Removal and installation of the rear bumper Lada Largus

Front and rear bumper Lada Largus

In 2008, the Russian AvtoVAZ acquired from the French Renault the entire list of rights to produce and sell models built using the common R90, F90 and B0 platforms.
An addition was the fact of a deal to equip cars with engines with 1.4 and 1.6-liter volumes. This approach allowed the universal version of the Lada Largus to appear in the automotive world. This car is a joint project of several corporations, although the Dacia Logan MCV model was used as a prototype. The exterior of the universal “Russian” Lada Largus is made in a simple style, where the components do not have intricate design delights. Manufacturers have used traditional rectilinear forms of body panels, small overhangs that help quickly overcome potholes, and wide moldings located on the side elements. Also, the sides of the car have an impressive glass area, which contributes to good visibility. The stern doors are hinged and have useful latches that allow you to hold the doors in any position, from perpendicular to the body to fully open. Sometimes the owners of the model install a cover on the rear bumper.

Rear bumper Lada Largus (removal and installation)

The rear bumper of the Lada Largus is removed in case of body work, or when replacing it. The peculiarity of removing the rear bumper is that with the bumper it is also necessary to remove the rear light from the car.

Tools necessary for removing the rear bumper of Lada Largus

You will need: a 10mm socket head, TORX T20 and TZO keys, a flat-blade screwdriver.

Operations when removing the rear bumper from a Lada Largus car

1. Remove two screws securing the fender liners to the rear bumper on both sides.

2. Unscrew the two plastic holders securing the fender liner to the wheel arch and remove the fender liner.

3. From the bottom of the car, remove one screw each (on the left and right sides) securing the corner of the bumper to the wheel arch.

4. Remove the rear lights “Replacing the rear light of Lada Largus”. 5. Remove two screws on the left and right sides securing the bumper sides to the rear pillars.

6. Remove the four screws securing the lower edge of the bumper to the amplifier.

7. Remove the four screws securing the upper edge of the bumper to the tailgate opening.

8. Lower the front corners of the bumper down a little to bring the stops A out of the holes in the lower edges of the rear fenders.

9. Press the plastic clips 1-6 (Fig. 1) of the holders 7 of the bumper sidewalls through the gaps formed between the bumper and the wings, and move the sidewalls slightly to the side.

10. Press the bumper stop latches on the left and right sides...

11. ...and moving it back, remove the bumper.

12. Install the rear bumper in the reverse order of removal.

Rice. 1 Fastening the side of the rear bumper of Lada Largus: 1-6 - plastic clips; 7 — bumper side holder

Why do you remove the bumper?

This action is prompted by a not so wide range of reasons. If there is a need for dismantling, then for this purpose it is not at all necessary to go to a service center. An ordinary Lada Largus driver is quite capable of handling this procedure on his own and, in addition, saving a considerable financial resource.

So, let's take a closer look at cases when it is necessary to dismantle an element.

1. Breaking. This can happen in an accident or during careless parking. The latter case in most cases assumes the integrity of the body element itself, and its paintwork is damaged.
2. Needs painting. This event involves removal, which will ensure better quality of painting work compared to a similar procedure without dismantling the element.
3. Body modernization. Some owners seek to update the exterior of their “horse” and are inclined to replace the standard product with a tuning element. Plus there is a cover on the rear bumper.
4. The need to install additional tools. Such accessories may include parking sensors, a camera, etc.
5. When installing overlays.

How to remove the stern bumper?

Many will find useful information on how to remove the bumper. To perform the indicated procedure, that is, remove the rear bumper, you will need a certain set of tools. Their composition is as follows:

• a head having a size of “10”;
• nozzles “T20” and “T30”;
• a screwdriver with a flat profile for removing clips.

Regarding the time costs, we note that the entire list of actions when you need to remove the rear bumper will take no more than one hour. Some craftsmen manage to carry out dismantling in less time, which is facilitated by accumulated experience.

After preparing the tools, you will need to provide access to the bottom of the car. We install our Lada Largus over a pit or hang it using jacks. Some experienced owners are able to complete the dismantling procedure without lifting the car, but this is guaranteed to entail additional time costs.

How to remove the rear bumper.

1. We disconnect the fender liners from the base.
2. Now, using a socket set to “10”, we unscrew a pair of fixing screws on each side of the car.
3. We move inside the fender liner and find the screws that secure the part itself to the body panel. We also unscrew them.
4. Next you will need to remove the lights. Alternatively, the bumper can be dismantled together with these devices.
5. We proceed to unscrewing the fasteners that connect the bumper to the amplifier.
6. On the top of the bumper, near the luggage compartment seal, there are 4 screws that will also need to be unscrewed.
7. We take a screwdriver and carefully remove the side sections of the bumper from the brackets (we work from both sides).
8. Now you can remove the Lada Largus Cross bumper itself by applying a pulling force first downwards and then towards yourself (backwards).

Removing and replacing the rear bumper on a Lada Largus: photos and videos

Dismantling the rear bumper of the Lada Largus is necessary for repair and restoration work on the part itself or the elements underneath it. So, removing this spare part with your own hands is not so difficult. It is clear to create the necessary conditions and have the tools that will be needed.

Required tool for replacement

As in all cases, to remove a car part you will need tools. To remove the rear bumper from a Lada Largus, you need a minimum kit, which many owners probably have. So, let's look at what is needed: the 10th head, T20 and T30 nozzles, and, as in the case of the front bumper, a flat-head screwdriver or a special tool for removing clips.

Rear bumper removal process

The process of dismantling the rear bumper is not complicated and will take from 30 minutes to 1 hour, depending on the abilities of the person who will carry out this operation.

But before you start work, you need to prepare your workplace. To remove the buffer, access from below is required. Of course, you can do without lifting the car, but it is better to perform operations on a pit or a lift.

So, let's look at the step-by-step process of removing the part:

1. First of all, you need to disconnect the fender liners from the bumper. To do this, using a 10mm socket, unscrew the screws securing the rear part of the fender liner on the right side and on the left (2 pieces each, 4 in total).

   The bolts in the diagram are indicated by a red arrow

2. There are screws under the fender liner that secure the bumper to the body. They need to be removed.

   Screws under the flap

3. The next difficult step is dismantling the lights. Without this, it becomes impossible to remove the bumper.
4. We unscrew the screws that secure the bumper to the amplifier.
5. Between the sealing rubber of the trunk and the bumper there are 4 screws that need to be removed; they secure the buffer to the rear panel.

6. Carefully, using a plastic screwdriver, remove the side parts of the bumper from the clamps.
7. Press the edges of the front part of the rear bumper away from the fender.

8. With a slight downward and backward movement, we dismantle the buffer.
9. Assembly, as always, is carried out in reverse order.

Now the bumper is removed, and you can carry out the remaining manipulations.

Possible reasons for withdrawal

There are not so many reasons for removing the front bumper on Largus, but they all contribute to learning how to dismantle such parts with your own hands. Let's consider what pushes the owner to perform this simple operation:

• Part damage . This can happen due to an accident or deformation when driving backwards.
• Another reason may be that the bumper itself was not damaged when damaged, but the rear panel was either deformed and requires restoration .
• Body painting , when carried out comprehensively, also requires removing the buffer.
• Tuning or upgrading the rear bumper will also require dismantling the part.
• Installation of accessories such as parking sensors will force the owner to remove the buffer.

• Partial removal to install bumper cover.

  Installing the rear bumper trim

• Other reasons.

There are not many reasons for removing the bumper; this is usually done after road accidents that caused damage to the part.

conclusions

Removing the rear bumper is easy and does not require special knowledge and skills. Installation can also be carried out easily without the use of special tools. Any car enthusiast can carry out this operation without going to a car service center.

Removing the front bumper

Let us remind you that the usual cases requiring the removal of this element, or rather the front bumper, are:

• need for repairs;
• the need to provide access to assemblies and components hidden under the bumper;
• for painting (renewing the coating) or replacing with an analogue;
• if you need to remove the radiator grille.

To remove the front bumper we use the following set of tools:

• mounting blade;
• flat head screwdriver;
• a “10” head or a wrench with a similar dimension;
• nozzle "T30".

Remove the front bumper.

1. The first step is to unscrew the 3 screws that secure the plastic protective panel of the engine compartment to the bumper.
2. On the rear sections of the element, pull out the clip cores, then remove the clips themselves from the mounting sockets.
3. We remove one piston from the mudguard attachment points.
4. After disconnecting the upper part of the mudguard from its lower segment, remove it.
5. We dismantle the fender liner, and then the lower part of the mudguard.
6. The work on the left side of the car is different from the right in that here you will need to disconnect the cable harness connecting the front fog lights with the on-board electrical network.
7. We proceed to unscrewing the lower edge of the component to the subframe.
8. We disconnect the side sections of the Lada Largus Cross bumper, located in both arches near the wheels, from the wings by unscrewing one screw at a time.
9. We move under the hood and unscrew the 4 bolts that hold the edge of the bumper to the radiator frame.
10. We first pull the back corners of the product down, holding the stops in the form of holes.
11. Now we move the side sections of the element forward and the bumper moves from its seat. If the specified cable harness interferes with the process, it can be safely removed.
12. We unscrew the 4 screws holding the headlight units and dismantle both devices.
13. 13. Finally, pull out the plastic clips located on the inside of the body and remove the front grille along with the air ducts. Now the Lada Largus Cross bumper has been completely dismantled.

The installation procedure is the reverse of removal.

Rear and front bumpers of the Lada Largus car

Quite often, after a minor accident, some Lada Largus bumper needs to be replaced. To make repair work easier, it is advisable to raise the car to a small height. Replacement of the rear bumper is carried out as follows. In order to remove it, you must first release the fender liner, which is held on by four bolts. After this, the Lada Largus bumper is disconnected from the arches. Here you need to unscrew one bolt on each side of the arch. Next, the rear lighting devices are removed.

Repair of damaged surface

After this, you need to release the amplifier. Unscrew four screws from the bottom and top. In the wheel arches, the bumper-to-body attachment is also removed. To dismantle the bumper on a Largus car, you need to snap off the latches and release the fangs. To do this, lower it down and pull it towards you. If the dismantled part has minor damage, for example, a small crack, then almost any driver can repair the bumper of a Largus car.

This requires the following tools and materials:

• sandpaper;
• mechanic's knife;
• soft spatula;
• grinding bar;
• automotive putty;
• primer;
• paint to match the color of the car.

The surface around the crack formed is cleaned of dirt and grease. Next, the edges of the split part are melted with a gas burner. Then all existing irregularities are smoothed out with sandpaper. The surface to be treated is thoroughly cleaned and leveled. After this, a shallow groove is cut between the edges with a fitter's knife, into which putty is applied in the required quantity. The putty material is applied to the Largus car bumper with a soft spatula. The layer should be smooth and uniform.

After the protective layer has completely hardened, all existing bumps are finally smoothed out with a sanding block, and the excess putty is removed. When sanding the Largus rear or front bumper, it is advisable to moisten the surface to be treated with water. This will significantly reduce the amount of dust emitted, which contains components harmful to health.

Once the sanded area has dried thoroughly, you can begin painting the rear buffer.

To do this, carefully seal the areas around the painting area with paper. After this, a thin layer of automotive primer is applied. When the primer is completely dry, the area is painted over with specially selected paint. You can select the desired paint tone that completely matches the color of the car at a specialized service center. There they do this using a computer using the appropriate program.

Vehicle safety

Today, the front integrated bumper on Largus is most often made of plastic. The part is a solid-cast volumetric structure mounted on supporting brackets. Thanks to the good elasticity of the plastic, the Largus bumper serves as a shock absorber when the car collides with an obstacle. This property of plastic has saved a considerable number of human lives during road accidents.

The height of the buffer is usually in accordance with international standards. These standards are aimed at ensuring that in the event of a small impact, the car body receives minimal damage. In addition, the height of the front buffer is influenced by the calculation of causing minimal harm to a pedestrian who could be hit by a moving car. That is why most technical innovations relating to this body part are primarily aimed at improving safety standards.

To protect the rear of the car from any damage during parking, a special reinforcement made of stainless pipe is installed. Typically, such a pipe is mounted on brackets located on both sides of the car. If there is a towbar at the rear, then the Largus bumper receives a separate side reinforcement on each side.

To ensure that the front or rear bumper on a Largus car always has a neat appearance, a special decorative trim is most often installed. In addition to improving the visual perception of the car, as well as increasing the level of its external aesthetics, such an overlay well protects the paintwork from various cracks or chips.

Dismantling for body repair

Often, the front bumper on a Largus car is dismantled to carry out body repairs or replace the radiator grille. To remove it, you need to have a universal screwdriver and a 10mm open-end wrench.

After this, on each side the lower part of the mudguard is disengaged. The fog light wires are disconnected in the left wheel arch. Then the lower edge of the bumper is released from the front suspension subframe. Next, unscrew the four upper screws located under the hood. After this, the fangs are released and the part is removed.

To remove the fog lights, you need to pull out the wiring harness from the special plastic holders. Next, three fastening screws are unscrewed on each headlight.

Source: https://expertvaz.ru/lada-largus/zadnij-bamper.html

How to remove and install the front and rear bumpers on a Lada Largus

AvtoVAZ bought in 2008 from the automobile manufacturer Renault the right to assemble and distribute cars built on the basis of the R90, F90 and B0. A deal was also made on the possibility of using engines (1.4 and 1.6 liters). This is how the Lada Largus car was born. This is a joint project of several companies at once. In fact, the model is an exact copy of the Renault Logan, except for some changes in appearance and a different logo.

In general, the appearance of the Lada can be said in a few words - simply and without unnecessary details. Rectangular shapes, clean lines, small overhangs and wide side moldings. From the side the body is straight with a large glass part. The rear doors are hinged. They are equipped with comfortable position locks when opening (from fully open to perpendicular to the car).

Step-by-step instructions for removing the rear bumper

Replacing the rear bumper with your own hands after dismantling the front guard (cross dismantling) begins with its removal, for which you need to go through the following algorithm of actions:

1. Disconnect the rear wheel arch liners using a 10 mm socket wrench. In total, at the first stage you will have to unscrew five screws.

2. Open the luggage compartment doors on the right and left sides of the vehicle one by one. Look under the removed fender liners for a few more screws securing the bumper to the car body. They should also be carefully unscrewed and pulled out. 3. The third step is to remove the headlights. 4. Next, unscrew the screws that attach the rear bumper to the amplifier. 5. Inspect the space between the rubber seal located on the trunk and the bumper itself, you will find 4 screws and unscrew them. 6. Using a flat (preferably plastic) screwdriver, carefully separate the left and right parts of the car bumper from the clips and press the edges that attach the part to be removed to the car fender. 7. After disconnecting the bumper from all holders, separate it from the Largus body by performing a “down and back” movement.

Why dismantle

There may not be many reasons for a driver to remove the bumper on his car. It is not at all necessary to contact a service center for this, where you will have to pay a considerable amount for repairs. Everything can be done with your own hands. Why the driver may need to remove the bumper:

• Breakdown – this happens as a result of a traffic accident or improper parking. It happens that the part itself is intact, but the back panel requires repair.
• Painting – requires dismantling for better painting of the body.
• Body improvements - installation of a new bumper, etc.
• Installation of additional accessories, for example, parking sensors, etc.
• Installation of overlays, etc.

Largus rear bumper removal video

Place the car on a two-post lift and brake it with the parking brake (electro-hydraulic lift type P-3.2 G).

Open the hood and disconnect the earth wire terminal from the battery.

Raise the car to a height convenient for doing the work.

Unscrew two self-tapping screws 2, Figure 3-1, from the right and left sides of the car, securing the casing to the bumper.

Move the wheel arch protective casing aside and unscrew bolts 1 of the side bumper fastening on the right and left sides of the car (replaceable Torx T30 head, extension, wrench).

1 – bolt of the side fastening of the bumper; 2 – self-tapping screw securing the casing to the bumper; 3 – protective casing of the rear wheel arch

Unscrew five screws 1, Figure 3-2, of the lower bumper mounting (replaceable Torx T30 head, wrench).

1 – screw for lower bumper mounting

1- side bracket for rear bumper

Remove the sidewalls of the bumper from engagement with the side brackets 1, Figure 3-3.

Unscrew the eight bolts 1 securing the bumper, Figure 3-4 (replaceable Torx T30 head, wrench).

Remove the rear bumper.

1 – bolt of the upper bumper fastening

Installation is carried out in the reverse order of removal.

The insurance company paid 10,154 rubles... Not enough, of course! But quickly enough and in cash, and not in a direction for repairs. I didn’t turn to an independent expert, I decided to fix it with the money I had. Moreover, the case is not complicated.

I was looking for a bumper in Exist. I found it for 8 thousand, I think... Original Lada, not painted. I didn’t buy it, of course!

I personally am not a fan of restoring broken bumpers. Unless it's some very rare car that doesn't have cheap new bumpers. Old American, for example