How to remove and install bumpers on a Chevrolet Lanos: instructions for replacing body kits

Chevrolet Lanos is on the world list of the most popular small cars and was originally assembled in Korea at local production facilities. This circumstance left its mark on the features of its design. Therefore, circumstances periodically arise that require knowledge of how to remove the rear bumper on a Chevrolet Lanos.

Tools needed to get the job done

Since the manufacturer has tried to make it as easy as possible for the car owner to carry out repairs and maintenance, the tool used to dismantle the above-mentioned car structural elements is as simple as possible. Its mandatory set includes:

Phillips-blade screwdriver;
socket head at “10” and “12”;
key to "10".

In addition, it is worth preparing in advance the instructions for the car or a printout of the step-by-step dismantling algorithm so that, if necessary, you can check the progress of the work and make the necessary adjustments to it. It is also worth taking care of safety in advance and turning off the power to the car. To do this, remove the terminals from its battery.

Removing Chevrolet Lanos bumpers is greatly facilitated by placing the car on a jack or inspection hole; this must be done in advance before removing them.

Removing, disassembling and installing the Lanos front bumper

1. Remove the mudguards and front wheel fenders on both sides of the car

2. Open the hood, place it on the stop and unscrew one nut at a time from the top fastening of the front bumper to the body on the left.

4. In the front wheel arches, unscrew two nuts for the front bumper-to-body mounting.

5. Remove one bolt of the lower fastening...

6. ...one side mounting screw each.

7. and remove the front bumper.

8. If necessary, remove the five screws securing the frame of the energy-absorbing element to the upper edge of the bumper, and four screws to the lower edge of the bumper.

Replacing the front bumper

In the event that you do not know how to remove the front bumper of a Chevrolet Lanos, it is best to take a more experienced partner with you to the garage. If you have at least a little experience in carrying out such operations, you can do all the work yourself. Its step-by-step algorithm is as follows:

We dismantle the mudguard by unscrewing the screws securing it using a Phillips screwdriver.
We dismantle the headlights and remove the fog lamp wire blocks.
On the left side of the car, unscrew the three screws intended for attaching the fender liners to the bumper. We perform similar operations on the other side.
Using a “10” key, unscrew the bolt that secures the bracket to the body.
We repeat the operation on the other side of the machine.
Using a socket set to “12”, unscrew the bolt, as well as the two nuts securing the bumper bracket to the body.
We take him aside.
We disconnect the fog lights from it.
In order to remove the energy-absorbing beam, using a Phillips-head screwdriver, unscrew the piston screw that secures its frame to the bumper.
We remove the piston.
The remaining eight pistons are removed in a similar order.
The energy-absorbing beam is dismantled.

Part selection

On a Chevrolet Lanos, the bumper has no analogues of the original part, of course, unless you take the tuning version. So, what are the front buffers:

Front bumper Lanos.

96226164 — original catalog number of the front bumper for Chevrolet Lanos. The cost of the product is 20,000 rubles.

List of analogues that can be used:

Manufacturer's name	Catalog number	Price
Fps	FP 1106 907-P	5000
Tempest	020 0139 900	5000
Blic	5510-00-1106900P	5000

How to remove and put back the rear bumper

Replacing the rear bumper on a Lanos is also carried out according to a certain algorithm, while the preparatory measures completely copy similar measures carried out in the process of preparing the front shock-absorbing element for dismantling. The step-by-step algorithm is as follows:

Remove the mudguards and rear wheel fenders on both sides of the car.
To do this, use a Phillips screwdriver to unscrew the self-tapping screws attaching the mud flaps to the corresponding parts of the rear wheel fender liners, as well as the self-tapping screws attaching them to the car body.
open the trunk lid and remove the panel trim and rear lights.
Unscrew the nuts and remove the bolts securing the ends of the bumper to the body.
Do the same procedure from the inside of both wheel arches.
Unscrew the four screws securing the central bumper mount and remove it.
in the case when the design of the element being dismantled requires this, unscrew the two nuts securing the damper to the body from inside the trunk.
remove the energy-absorbing beam.
The side energy-absorbing element is dismantled in a similar way.
The central part of the bumper is also removed by unscrewing the four fastening screws.

Installing the Lanos rear bumper backwards is done in the reverse order. Before starting this procedure, you will need to thoroughly wipe the fastening areas in order to remove dirt and rust from them. In addition, it is advisable to use the services of an assistant who will support the part during installation.

How to Remove the Front Bumper on a Chevrolet Lanos ~ AUTOTEXNIKA.RU

Repair and maintenance of cars, engines and automatic transmissions

Chevrolet Lanos body repair

Chevrolet Lanos bearing. perceives all loads and forces exerted on the car while driving. It has greater rigidity than a frame-mounted body. This provides a high level of safety and comfort for the driver and passengers.

Rice. 44. Replacing body parts on a Chevrolet Lanos

1. front bumper; 2. hood with radiator; 3. front wing; 4. External rear view mirror; 5. entrance door; 6. rear doors; 7. trunk lid; 8. Chevrolet Lanos rear bumper

Passive safety elements. When a Chevrolet Lanos collides with an obstacle during an accident, the body structure is deformed to dissipate the impact energy, while the interior of the vehicle must not be deformed to preserve the living space of the driver and passengers.

Most of the side impact energy should be absorbed by the central supports of the Chevrolet Lanos. In addition, the door has protective grilles. These items also include head restraints, seat belts and air bags.

Three-layer glass (triplex). made of two glasses, which are connected to each other by an intermediate plastic film. When the glass breaks, it breaks into many fragments that hold the film and do not fly around the cabin.

Inertia coils. Make sure the seat belts fit snugly against the driver and passenger. No need to adjust the belt length. In the event of a vehicle collision, the inertia reel locks the seat belt.

Chevrolet Lanos, which removes dirt and wheel arches

Rice. 45. Types of pistons “A” and “B” Chevrolet Lanos console lock cover

Oil seals and mudguards were removed to replace the anti-corrosion body of the Chevrolet Lanos. The operations are shown on the wheel arch lining and on the left wheel cover. The fender and medlar of the right front wheel are removed in the same way.

For convenience, remove the wheels. Using a Phillips screwdriver, unscrew the two spray bar nozzles and the bottom bracket to the sill. We remove dirt.

Using a Phillips screwdriver, loosen the three front bumper screws on the Chevrolet Lanos front fender. The reel is equipped with four type A pistons and one type B piston.

To remove the "A" type piston, you need to move the retainer using a screwdriver or a round rod, and to remove the "B" type, it must be disconnected from the pin. We remove the pistons and remove the fender liner. Reinstall the wheel arch trim.

READ How to Remove the Instrument Cluster on a Hover

Unlocking Chevrolet Lanos hood

Work is underway to replace or adjust the Chevrolet Lanos lock body; replace the locking cable. Remove the left front front wheel arch. Mark the position of the lock relative to the radiator frame.

Summary

Despite the fact that the Chevrolet Lanos is a reliable, strong car with a bumper of appropriate quality, it periodically breaks down. This part of the machine’s design has to be changed periodically. This is quite simple to do, since the designers took care of this, but some precautions must be taken. So, for example, if you do not unscrew all the fastening elements in the area of the wheels and use force during dismantling, the product will simply break and you will have to buy a new one at a fairly high price. In the same case, when all precautions are followed, the repair will be easy and without any special incidents.

Reasons for dismantling

When you have dealt directly with the process of disassembly and dismantling, it is worth deciding why it is still necessary to remove this unit:

A sufficient number of motorists, when operating a vehicle, do not maintain distance and intervals, thereby damaging the bumpers. Thus, dismantling an element may be necessary for repair and restoration operations or painting.

The second factor where it may be necessary to dismantle the front bumper is the repair of components under the part. Thus, many engine operations require additional access, which can be provided by a removed buffer.

Also, in addition to repair and restoration operations on the bumper, it may require replacement when it cannot be repaired.

Buying a new bumper

Be sure to take into account that a painted Chevrolet Lanos bumper will cost almost twice as much as the black blank itself. As mentioned above, it is possible to restore the bumper, but this is not always advisable. If you want a new front bumper for Chevrolet Lanos, look for part number 96226164. It can be either original or a copy. By the way, the front bumper of the Chevrolet Lanos is catalog number 96226147.

Chevrolet Lanos brakes: hand brake

Replacing the cylinder head gasket on a Chevrolet Lanos

Chevrolet Lanos steering rack

The video could have been shot better! can not understand anything…

The article helped, the video was shot quite clearly, don’t listen to the commentator above. The main thing is straight hands.

Source

Why is the front panel of a car called a dashboard?

Car owners often hear the word torpedo, which does not mean a combat projectile at all, but the front instrument panel of a vehicle. Why did the torpedo become synonymous with the front panel of the car? Today, if you ask a modern driver why he calls the panel a torpedo, you probably won’t hear another answer other than a shrug.

To understand what a car panel and a dashboard have in common, you need to plunge into the past. The word dashboard was first used in a car in 1947, when a car with an unusually shaped front panel was released. All controls were located around the steering wheel. This arrangement of instruments got its name due to the fact that the company that produced the panel was called “Torpedo”. It was due to this company that the name of the front panel was established.

The Torpedo company was engaged in the production of front panels for cars, and was located in Germany. Since the emergence of the company, most car brands began to be equipped with front panels from this particular manufacturer. Since then, the name torpedo has stuck. This is how modern copying machines are called copiers, which comes from the name of the company Xerox.

Removing the rear bumper of Daewoo/Chevrolet Lanos: video

You can dismantle the rear bumper of a Daewoo/Chevrolet Lanos with your own hands and without any problems. So, in order to dismantle the protective part, it is worth knowing the design features of the car, as well as where the product is attached to the car body.

Video

The videos will tell you how to quickly remove the front bumper from a car, and also tell you about the nuances and tricks of the process.

Chevrolet Lanos front bumper: what is it and how to replace it

It makes sense to repair the front bumper of a Chevrolet Lanos only if the damage is not severe (a small crack). Otherwise, it would be more advisable to purchase a new one. Since the model is almost the most common on our market, finding bumpers, both new and used, but in good condition is not a problem at all. Often, replacing the front bumper of a Chevrolet Lanos is carried out at a service station, but in fact, you can do it yourself. The process is simple, there is nothing complicated about it.

Dismantling process

To begin with, you should understand that removing the bumper can be quite easy and simple, and does not require much effort. There is also no need to look for special-purpose equipment, such as in engine-related operations. Also, to dismantle the bumper, you don’t need a hole or a lift, you only need a flat surface.

It is worth understanding that in order to remove the front bumper you will need to remove the accompanying parts, so you will need a jack and a set of tools, which must include Torx sprockets and other attachments.

Let's get started with the work:

Remove the bumper mudguard. We remove the headlights and disconnect the wiring harness connectors from the fog lights. On each side of the car, unscrew three screws securing the front wheel arch liners to the bumper. Using a Phillips screwdriver, unscrew the self-tapping screw securing the bumper to the front fender bracket.

Using a 10mm spanner, unscrew the bolt securing the bumper to the body bracket.

Use a 12mm socket to unscrew the bolt...

... and two nuts securing the bumper bracket to the body. We perform similar operations on the other side of the car.

We remove the bumper. Disconnect the fog lights from the bumper

To remove the energy-absorbing beam of the front bumper, use a Phillips screwdriver to unscrew the screw of the piston securing the frame of the energy-absorbing beam to the bumper...

... and remove the piston.

Similarly, we remove the remaining 8 pistons securing the frame of the energy-absorbing beam to the bumper.

We disconnect the frame from the bumper.

We remove the energy-absorbing beam. We assemble and install the front bumper in the reverse order.

Assembly is carried out in reverse order.

Conclusion

You can replace the front bumper of a Chevrolet Lanos with your own hands. So, you will need a set of tools and time, as well as some knowledge in the design and fastening of automotive parts.

source